Dtc 32 (1) Injection Pump System Malfunction

Двигатель Гибридная Система Land Cruiser Prado.
Система Управления Двигателем 5L-E.

DESCRIPTION

WIRING DIAGRAM

INSPECTION PROCEDURE

CHECK HARNESS AND CONNECTOR (ECM - INJECTION PUMP CORRECTION UNIT)

REPLACE INJECTION PUMP ASSEMBLY

CHECK DTC OUTPUT (CHECK IF DTC 32 (1) IS OUTPUT AGAIN)

DTC 32 (1) Injection Pump System Malfunction


DESCRIPTION

To compensate for the change in injection volume and injection timing caused by the variance in the injection pump itself, a correction is made by using the data that is stored in the ROM in the fuel pump correction unit.

DTC No.
DTC Detection Condition
Trouble Area
32 (1)
  1. When the ignition switch is turned to ON, or when the ECM determines if there is an error in the RAM of the ECM, the ECM conducts single communication. If one of the following conditions occurs in single communication, the ECM conducts another communication. While the ECM is conducting communication, the ECM stores DTC 32 (1) if (a) occurs 20 times continuously, (b) occurs 20 times continuously, or (c) occurs 2 times continuously.
  2. (a) There was a communication error when receiving data.
  3. (b) Data sent from the injection pump correction unit does not match the data received in the ECM.
  4. (c) Data received from the pump ROM is not input for 1024 msec.
    УКАЗАНИЕ:
    Even when determining if the process is completed normally, if an undefined code is found while checking the identification code of data received, the ECM conducts communication again. If an undefined code occurs 20 times continuously, the ECM stores DTC 32 (1).
  1. Open or short in injection pump correction unit circuit
  2. Injection pump correction unit
  3. ECM

WIRING DIAGRAM


.Система Управления Двигателем 5L-E.Система Ecd. Dtc 32 (1) Injection Pump System Malfunction


INSPECTION PROCEDURE

1.CHECK HARNESS AND CONNECTOR (ECM - INJECTION PUMP CORRECTION UNIT)

  1. Disconnect the injection pump correction unit connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    		Condition
    		Specified Condition
    C107-1 (DATA) - C102-6 (DATA)
    		Always
    		Below 1 Ω
    C107-4 (CLK) - C102-14 (CLK)
    		Always
    		Below 1 Ω
    Standard Resistance (Check for Short):
    Tester Connection
    		Condition
    		Specified Condition
    C107-1 (DATA) or C102-6 (DATA) - Body ground
    		Always
    		10 kΩ or higher
    C107-4 (CLK) or C102-14 (CLK) - Body ground
    		Always
    		10 kΩ or higher

  1. Reconnect the injection pump correction unit connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2.REPLACE INJECTION PUMP ASSEMBLY

  1. Replace the injection pump assembly (See page Нажмите здесь).


NEXT


3.CHECK DTC OUTPUT (CHECK IF DTC 32 (1) IS OUTPUT AGAIN)

  1. Connect the intelligent tester to the DLC3.

  1. Clear the DTC (See page Нажмите здесь).

  1. Turn the ignition switch to ON and turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read the DTCs (See page Нажмите здесь).

    Result
    Result
    		Proceed to
    DTC 32 (1) output again
    		A
    No DTC output
    		B


B
SYSTEM OK
A

REPLACE ECM (Нажмите здесь)