Fuel Supply Pump Installation

Install a new O-ring to the fuel supply pump.

Install the supply pump drive coupling.

ПРИМЕЧАНИЕ:

When reusing the coupling, it must be installed in the same orientation (top/bottom, front/back) as when it was removed.

УКАЗАНИЕ:

Line up the coupling with the groove in the camshaft end.

Install the supply pump with the 2 bolts.

Момент затяжки:

21 Н*м{209 кгс*см, 15 фунт-сила-футов}

ПРИМЕЧАНИЕ:

Apply engine oil on the O-ring of the supply pump.

УКАЗАНИЕ:

Line up the end of the supply pump drive shaft with the supply pump drive coupling.

Connect the suction control valve connector.

Connect the fuel temperature sensor connector.

Temporarily install the fuel inlet pipe with the 2 clamps and nut.

Using SST, first tighten the nut at the common rail end of the fuel inlet pipe.

Специальный инструмент (SST):

09023-38401

Момент затяжки:

27 Н*м{275 кгс*см, 20 фунт-сила-футов}for use with SST

30 Н*м{306 кгс*см, 25 фунт-сила-футов}for use without SST

УКАЗАНИЕ:

1. Use of the proper SST is required to ensure that the correct torque is applied to the injection pipe nut.
   
2. Use a torque wrench with a fulcrum length of 30 cm (11.81 in.).
   
3. Make sure that the pipe is not deformed or twisted during installation.
   If the pipe is deformed or twisted, or if it cannot be installed properly, replace the pipe with a new pipe.
   

Using SST, tighten the nut at the supply pump end of the fuel inlet pipe.

Специальный инструмент (SST):

09023-38401

Момент затяжки:

27 Н*м{275 кгс*см, 20 фунт-сила-футов}for use with SST

30 Н*м{306 кгс*см, 25 фунт-сила-футов}for use without SST

УКАЗАНИЕ:

1. Use of the proper SST is required to ensure that the correct torque is applied to the injection pipe nut.
   
2. Use a torque wrench with a fulcrum length of 30 cm (11.81 in.).
   
3. Make sure that the pipe is not deformed or twisted during installation.
   If the pipe is deformed or twisted, or if it cannot be installed properly, replace the pipe with a new pipe.
   

Tighten the fuel inlet pipe clamp nut.

Момент затяжки:

5.0 Н*м{51 кгс*см, 44 фунт-сила-дюймов}

Using pliers, grip the claws of the 2 clips and slide the 2 clips to install the No. 1 fuel hose.

Using pliers, grip the claws of the 2 clips and slide the 2 clips to install the No. 3 fuel hose.

Install the cleaner case with the 3 bolts and connect the wire harness clamp.

Момент затяжки:

5.0 Н*м{51 кгс*см, 44 фунт-сила-дюймов}

Install the air filter element.

Insert the hinge parts of the air cleaner cap into the air cleaner case, and then hang the 3 hook clamps.

Connect the mass air flow meter connector.

Engage the wire harness clamp.

PERFORM ACTIVE TEST

1. Connect the intelligent tester to the DLC3.
   

2. Start the engine.
   

3. Turn the intelligent tester ON.
   

4. Enter the following menus: Powertrain / Engine / Active Test.
   

5. Perform the Active Test.
   
   

   Intelligent Tester Display	Test Details	Control Range	Diagnostic Notes
   Test the Fuel Leak	Pressurizing common rail internal fuel pressure, and checking for fuel leaks	Stop/Start	Fuel pressure inside common rail pressurized to specified value and engine speed increased to 2,000 rpm when start is selected Above conditions to be maintained while test is started

Using the hand pump, bleed air from the fuel system until pumping becomes difficult.

Attach the 4 clips to install the engine cover.