INSTALL SEAT POSITION SENSOR (for Power Seat)

INSTALL SEAT POSITION SENSOR (for Manual Seat)

INSTALL FRONT SEAT ASSEMBLY (for Power Seat)

INSTALL FRONT REAR INNER SEAT TRACK COVER LH (for Power Seat)

INSTALL FRONT REAR OUTER SEAT TRACK COVER LH (for Power Seat)

INSTALL FRONT INNER SEAT TRACK COVER LH (for Power Seat)

INSTALL FRONT OUTER SEAT TRACK COVER LH (for Power Seat)

INSTALL FRONT SEAT CUSHION SHIELD (for Manual Seat)

INSTALL RECLINING ADJUSTER RELEASE HANDLE (for Manual Seat)

INSTALL VERTICAL ADJUSTING HANDLE (for Manual Seat)

INSTALL VERTICAL SEAT ADJUSTER KNOB CAP (for Manual Seat)

INSTALL VERTICAL SEAT ADJUSTER KNOB (for Manual Seat)

INSTALL FRONT SEAT ASSEMBLY (for Manual Seat)

INSTALL REAR INNER SEAT TRACK BRACKET COVER (for Manual Seat)

INSTALL REAR OUTER SEAT TRACK BRACKET COVER (for Manual Seat)

INSTALL FRONT INNER SEAT TRACK BRACKET COVER (for Manual Seat)

INSTALL FRONT OUTER SEAT TRACK BRACKET COVER (for Manual Seat)

INSTALL FRONT SEAT HEADREST ASSEMBLY

CONNECT BATTERY NEGATIVE TERMINAL (for Manual Seat)

PERFORM INITIALIZATION

INSPECT FRONT SEAT ASSEMBLY (for Power Seat)

INSPECT FRONT SEAT ADJUSTER ASSEMBLY (for Manual Seat)

INSPECT SRS WARNING LIGHT

Check that the engine switch is off.

Check that the negative battery (-) terminal is disconnected.

• CAUTION:

• After disconnecting the negative battery terminal, wait for at least 90 seconds before starting the operation.

Using a feeler gauge 1 mm (0.039 in.), install the seat position sensor.

• NOTICE:

• HINT:

• Be sure that a clearance between the seat position sensor and the seat rail is within 0.6 mm (0.023 in.) to 1.4 mm (0.055 in.).

Using a "torx" socket wrench (T30), tighten the "torx" screw to install the seat position sensor.

• Torque:
• 8.0 N*m{ 82 kgf*cm, 71 in.*lbf}

Make sure that a clearance between the seat position sensor and the seat rail is within 0.6 mm (0.023 in.) to1.4 mm (0.055 in.).

Check that there is no looseness in the installation parts of the seat position sensor.

Connect the connector.

Install the seat slide position sensor protector to the seat position sensor.

Check that the engine switch is off.

Check that the negative battery (-) terminal is disconnected.

• NOTICE:

• After disconnecting the negative battery terminal, wait for at least 90 seconds before starting the operation.

Using a feeler gauge 1 mm (0.039 in.), install the seat position sensor.

• NOTICE:

• HINT:

• Be sure that a clearance between the seat position sensor and the seat rail is within 0.6 mm (0.023 in.) to 1.4 mm (0.055 in.).

Using a "torx" socket wrench (T30), tighten the "torx" screw to install the seat position sensor.

• Torque:
• 8.0 N*m{ 82 kgf*cm, 71 in.*lbf}

Make sure that a clearance between the seat position sensor and the seat rail is within 0.6 mm (0.023 in.) to1.4 mm (0.055 in.).

Check that there is no looseness in the installation parts of the seat position sensor.

Connect the connector.

Install the seat slide position sensor protector to the seat position sensor.

Place the seat in the cabin.

Connect the connectors under the seat.

Connect the cable to the negative (-) battery terminal.

Operate the power seat switch knob and move the seat to the position farthest forward.

Tighten the 2 bolts on the rear seat track bracket.

• Torque:
• 37 N*m{ 377 kgf*cm, 27 ft.*lbf}

• HINT:

• Tighten the 2 bolts in the order indicated in the illustration.

Operate the power seat switch knob and move the seat to the rearmost position.

Tighten the 2 bolts on the rear seat track bracket.

• Torque:
• 37 N*m{ 377 kgf*cm, 27 ft.*lbf}

Engage the claw and install the seat cushion shield lower LH.

Engage the claw and install the reclining adjuster release handle.

Install the vertical adjusting handle with the 2 screws.

Engage the 3 claws and install the vertical seat adjuster knob cap.

Place the front seat assembly in the vehicle and align the adjuster pin with the hole on the vehicle side.

• NOTICE:

• When installing the passenger side front seat assembly, be careful not to step on the yaw rate sensor mounted on the floor under the seat.

Connect the connector.

Move the front seat assembly to the rearmost position by operating the slide handle.

• NOTICE:

• Check that the seat is locked.

Temporarily install the front seat track bracket with the 2 bolts.

Move the front seat assembly fully forward by operating the slide handle.

• NOTICE:

• Check that the seat is locked.

Temporarily install the rear seat track bracket with the 2 bolts.

Move the front seat assembly to the rearmost position by operating the slide handle.

• NOTICE:

• Check that the seat is locked.

Fully tighten the 2 bolts on the front seat track bracket in the order of the inner side bolt and then the outer side bolt.

• Torque:
• 37 N*m{ 377 kgf*cm, 27 ft.*lbf}

Move the front seat assembly fully forward by operating the slide handle.

• NOTICE:

• Check that the seat is locked.

Fully tighten the 2 bolts on the rear seat track bracket in the order of the inner side bolt and then the outer side bolt.

• Torque:
• 37 N*m{ 377 kgf*cm, 27 ft.*lbf}

Engage the 2 claws and install the rear inner seat track bracket cover.

Engage the 2 claws and install the rear outer seat track bracket cover.

Engage the 2 claws and install the front inner seat track bracket cover.

Engage the 2 claws and install the front outer seat track bracket cover.

Perform initialization .

• HINT:

• Some systems need initialization when disconnecting the cable from the negative battery terminal.

Check the power seat operation.

Check the seat heater operation (with seat heater system).

Inspect the SRS warning light .