Lexus IS250 IS220d GSE20 ALE20 - SEAT BELT
REAR SEAT OUTER BELT ASSEMBLY - REMOVAL
| 1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL |
- CAUTION:
- Wait for 90 seconds after disconnecting the cable to prevent airbag deployment.
| 2. REMOVE BENCH TYPE REAR SEAT CUSHION ASSEMBLY |
Detach the 2 front hooks of the seat cushion from the vehicle body.
- NOTICE:
- Follow the instructions below carefully as the cushion frame deforms easily.
Choose a hook to detach first. Place your hands near the hook as shown in the illustration. Then lift the seat cushion to detach the hook.
Repeat for the other hook.
Detach the 2 rear hooks of the seat cushion from the seatback.
Remove the seat cushion.
| 3. REMOVE REAR SEAT HEADREST ASSEMBLY |
| 4. REMOVE REAR SEAT CENTER HEADREST ASSEMBLY |
| 5. REMOVE BENCH TYPE REAR SEATBACK ASSEMBLY |
Using a screwdriver, detach the claws to open the cap of the 3 rear seat shoulder belt guides.
Using a screwdriver, detach the claw to open the cap of the 3 rear seat shoulder belt guides.
Remove the 4 bolts and rear seatback assembly.
| 6. REMOVE REAR DOOR SCUFF PLATE LH |
Put protective tape around the rear door scuff plate.
Using a moulding remover, disengage the 2 clips.
Disengage the 5 claws and remove the the rear door scuff plate LH.
| 7. REMOVE REAR DOOR SCUFF PLATE RH |
| 8. REMOVE REAR SEAT SIDE GARNISH LH |
Disengage the 5 claws and remove the rear seat side garnish LH.
| 9. REMOVE REAR SEAT SIDE GARNISH RH |
| 10. REMOVE ROOF SIDE INNER GARNISH LH |
Disengage the 4 clips and claw, and remove the roof side inner garnish LH.
| 11. REMOVE ROOF SIDE INNER GARNISH RH |
| 12. REMOVE PACKAGE TRAY TRIM PANEL ASSEMBLY (w/o Rear Sunshade) |
Remove the bolt and disconnect the floor end of the rear seat 3 point type belt assembly LH.
- HINT:
- Use the same procedures for the RH side and the LH side.
Remove the bolt and disconnect the floor end of the rear seat inner with center belt assembly RH.
Using a moulding remover, disengage the 4 claws and remove the rear seat shoulder belt cover LH.
- HINT:
- Use the same procedures for the RH side and LH side.
Using a moulding remover, disengage the 4 claws and remove the rear seat shoulder belt cover center.
Disengage the 3 clips and raise the front portion of the package tray trim panel assembly.
Pass the 3 rear seat belt floor anchors through the package tray trim panel assembly.
Disconnect the connector from the center stop light assembly.
Disengage the 5 claws and remove the package tray trim panel assembly and the center stop light assembly as a unit.
| 13. REMOVE PACKAGE TRAY TRIM PANEL ASSEMBLY (w/ Rear Sunshade) |
Remove the bolt and disconnect the floor end of the rear seat 3 point type belt assembly LH.
- HINT:
- Use the same procedures for the RH side and the LH side.
Remove the bolt and disconnect the floor end of the rear seat inner with center belt assembly RH.
Using a moulding remover, disengage the 4 claws and remove the rear seat shoulder belt cover LH.
- HINT:
- Use the same procedures for the RH side and LH side.
Using a moulding remover, disengage the 4 claws and remove the rear seat shoulder belt cover center.
Disengage the 3 clips.
Pass the 3 rear seat belt floor anchors through the package tray trim panel assembly.
Remove the package tray trim panel assembly.
| 14. REMOVE REAR SEAT 3 POINT TYPE BELT ASSEMBLY |
Using a screwdriver, pull out the locking button in the direction shown by the arrow to release the lock, and disconnect the pretensioner connector as shown in the illustration.
Remove the 2 bolts and the rear seat 3 point type belt assembly.