INSTALL REAR DRIVE SHAFT ASSEMBLY

INSTALL NO. 2 REAR UPPER CONTROL ARM ASSEMBLY

TEMPORARILY TIGHTEN NO. 1 REAR UPPER CONTROL ARM ASSEMBLY

TEMPORARILY TIGHTEN NO. 1 REAR SUSPENSION ARM ASSEMBLY

TEMPORARILY TIGHTEN NO. 2 REAR SUSPENSION ARM ASSEMBLY

INSTALL REAR DISC

INSTALL REAR DISC BRAKE CALIPER ASSEMBLY

INSTALL REAR SPEED SENSOR

INSTALL REAR AXLE SHAFT NUT

INSTALL NO. 3 PARKING BRAKE CABLE ASSEMBLY

INSTALL REAR STABILIZER LINK ASSEMBLY

STABILIZE SUSPENSION

FULLY TIGHTEN NO. 1 REAR UPPER CONTROL ARM ASSEMBLY

FULLY TIGHTEN NO. 1 REAR SUSPENSION ARM ASSEMBLY

FULLY TIGHTEN NO. 2 REAR SUSPENSION ARM ASSEMBLY

INSTALL NO. 2 DIFFERENTIAL SUPPORT PROTECTOR

INSTALL REAR WHEEL

INSPECT AND ADJUST REAR WHEEL ALIGNMENT

CHECK ABS SPEED SENSOR SIGNAL

Coat the spline of the inboard joint shaft assembly with gear oil.

Set the shaft snap ring with the opening side facing down.

Align the shaft splines and install the drive shaft assembly with a brass bar and hammer.

• NOTICE:

• HINT:

• It is possible to determine if the inboard joint shaft is properly engaged (the shaft is in contact with the pinion shaft, and the snap ring is engaged in the pinion gear) based on the sound or feeling when the shaft is driven in.

Install the rear drive shaft assembly to the rear axle carrier.

• NOTICE:

• Be careful not to damage the drive shaft boot.

Install the No. 2 rear upper control arm assembly to the rear axle carrier sub-assembly with a new nut.

• Torque:
• 70 N*m{ 714 kgf*cm, 52 ft.*lbf}

Temporarily tighten the No. 1 rear upper control arm assembly to the rear axle carrier sub-assembly with the bolt, washer and nut.

• HINT:

• Install the bolt from the rear side of the vehicle and lightly tighten the bolt.

Temporarily tighten the No. 1 rear suspension arm assembly to the rear axle carrier sub-assembly with the bolt and nut.

• HINT:

• Install the bolt from the rear side of the vehicle and lightly tighten the bolt.

Temporarily tighten the No. 2 rear suspension arm assembly to the rear axle carrier sub-assembly with the bolt and nut.

• HINT:

• Install the bolt from the rear side of the vehicle and lightly tighten the bolt.

Aligning the matchmarks, install the rear disc.

• HINT:

• When replacing the rear disc with a new one, select the installation position where the rear disc has the minimum runout.

Install the rear disc brake caliper assembly and No. 1 caliper plates with the 2 bolts.

• Torque:
• 54 N*m{ 551 kgf*cm, 40 ft.*lbf}

• NOTICE:

Install the speed sensor to the rear axle carrier with the 2 bolts.

• Torque:
• Bolt (A):
• 8.5 N*m{ 87 kgf*cm, 75 in.*lbf}
• Bolt (B):
• 6.0 N*m{ 61 kgf*cm, 53 in.*lbf}

• NOTICE:

Install a new axle shaft nut.

• Torque:
• 290 N*m{ 2,957 kgf*cm, 214 ft.*lbf}

Using a chisel and a hammer, stake the axle shaft nut.

Install the No. 3 parking brake cable assembly with the 2 bolts.

• Torque:
• 19 N*m{ 194 kgf*cm, 14 ft.*lbf}

Install the stabilizer link assembly and the load sensing valve sensor bracket to the No. 2 rear suspension arm assembly with the bolt and nut.

• Torque:
• 27 N*m{ 275 kgf*cm, 20 ft.*lbf}

Install the rear wheels.

Lower the vehicle to the ground. Bounce the vehicle up and down at the corners to stabilize the rear suspension.

Remove the rear wheels.

Jack up the axle carrier, with a wooden block placed between the jack and axle carrier, to apply a load to the suspension so that the rear drive shaft assembly becomes level.

Fully tighten the No. 1 rear upper control arm assembly with the nut.

• Torque:
• 161 N*m{ 1,642 kgf*cm, 119 ft.*lbf}

Temporarily tighten the No. 1 rear suspension arm assembly to the rear axle carrier sub-assembly with the bolt and nut.

• HINT:

• Install the bolt from the rear side of the vehicle and lightly tighten the bolt.

Fully tighten the No. 2 rear suspension arm assembly with the bolt and nut.

• Torque:
• 161 N*m{ 1,642 kgf*cm, 119 ft.*lbf}

• NOTICE:

• Turn the bolt while holding the nut.

Install the No. 2 differential support protector to the rear suspension member brace with the 2 nuts.

• Torque:
• 5.4 N*m{ 55 kgf*cm, 48 in.*lbf}