INSPECT RUNOUT OF DIFFERENTIAL RING GEAR

INSPECT DIFFERENTIAL RING GEAR BACKLASH

INSPECT TOOTH CONTACT BETWEEN RING GEAR AND DRIVE PINION

INSPECT DIFFERENTIAL SIDE GEAR BACKLASH

INSPECT DIFFERENTIAL SIDE GEAR BACKLASH

INSPECT RUNOUT OF DIFFERENTIAL DRIVE PINION

INSPECT DIFFERENTIAL DRIVE PINION PRELOAD

INSPECT TOTAL PRELOAD

INSPECT RUNOUT OF REAR DIFFERENTIAL CASE SUB-ASSEMBLY

Set the dial indicator perpendicular to the end of the ring gear face.

Rotate the ring gear and measure the backlash.

• Maximum runout:
• 0.05 mm (0.0020 in.)

If the runout exceeds the specified maximum value, remove the ring gear and check the runout of the differential case.

While holding the rear drive pinion companion flange, rotate the ring gear and measure the backlash.

• Backlash:
• 0.08 to 0.13 mm (0.0031 to 0.0051 in.)

If the backlash is not within the specified range, adjust the backlash or repair as necessary.

Coat 3 or 4 teeth at the 3 different positions on the ring gear with Prussian blue.

Rotate the ring gear in both directions.

Inspect the tooth contact pattern.

If the teeth are not contacting properly, use the following table to select a proper plate washer for correction.

• HINT:

Place a dial indicator on the tip of the pinion gear tooth at a right angle. Hold the side gear in the differential case and check that the backlash is 0 mm (0 in.).

If not, replace the rear differential case sub-assembly with a new one.

Hold the differential case in a vise between aluminum plates.

• NOTICE:

• Do not overtighten the vise.

Place a dial indicator on the tip of the side gear tooth at a right angle. Hold the pinion gear in the differential case and check that the backlash is 0 mm (0 in.).

If not, replace the rear differential case sub-assembly with a new one.

Using a dial indicator, measure the runout of the drive pinion shaft at a position 10 mm (0.39 in.) away from the end of the shaft.

• Maximum runout:
• 0.08 mm (0.0031 in.)

If the runout is greater than the maximum, replace the drive pinion and ring gear.

Using SST and a torque wrench, measure the starting torque of the drive pinion. The backlash between the drive pinion and ring gear should allow enough movement of the drive pinion to allow this measurement to be performed. Make sure not to include the preload of the ring gear (differential case) in the measurement of the drive pinion preload.

• SST
• 09229-55010

• Drive pinion preload (at starting):

• Specifications	Preload
  New bearing	1.22 to 1.80 N*m (12.4 to 18.4 kgf*cm, 10.8 to 15.9 in.*lbf)
  Reused bearing	0.50 to 0.80 N*m (5.1 to 8.2 kgf*cm, 4.3 to 6.9 in.*lbf)

If the preload is not within the specified range, adjust the rear differential drive pinion preload or repair as necessary.

Using SST and a torque wrench, measure the preload with the teeth of the drive pinion and ring gear in contact.

• SST
• 09229-55010

• Total preload (at starting):

• Grade: luxury

  Specifications	Preload
  New bearing	1.92 to 3.89 N*m (19.6 to 39.7 kgf*cm, 17.0 to 34.4 in.*lbf)
  Reused bearing	1.20 to 2.89 N*m (12.2 to 29.5 kgf*cm, 10.6 to 25.6 in.*lbf)

• Grade: sport

  Specifications	Preload
  New bearing	1.75 to 3.38 N*m (17.8 to 34.5 kgf*cm, 15.5 to 29.9 in.*lbf)
  Reused bearing	1.03 to 2.38 N*m (10.5 to 24.3 kgf*cm, 9.1 to 21.1 in.*lbf)

If the preload is not within the specified range, adjust the total preload or repair as necessary.

Install the differential case to the differential carrier.

• NOTICE:

• Do not damage the case bearing.

Using SST and a hammer, install the case bearing outer race on the ring gear tooth side.

• SST
• 09608-32010
  09950-70010(09951-07200)

• HINT:

• Tap in the case bearing outer race until half of the side gear shaft snap ring groove of the differential carrier can be seen.

Install SST to the differential carrier.

• SST
• 09571-50010

Tighten the SST bolt (A) until the SST disc slightly touches the case bearing outer race.

Using SST and a hammer, install the case bearing outer race on the ring gear back surface side.

• SST
• 09608-32010
  09950-70010(09951-07200)

• HINT:

• Tap in the case bearing outer race until it touches the case bearing inner race roller.

Using snap ring pliers, install the side gear shaft snap ring in the differential carrier on the ring gear back surface side.

Place a dial indicator on the differential case flange surface at a right angle.

Using a dial indicator, measure the differential case runout.

• Maximum runout:
• 0.05 mm (0.0020 in.)

If the runout is greater than the maximum, replace the rear differential case with a new one.

Using snap ring pliers, remove the side gear shaft snap ring on the ring gear back surface side.

Tighten the SST bolt to push out the ring gear back surface side case bearing outer race.

• SST
• 09571-50010

• NOTICE:

• Do not drop the case bearing outer race.

Remove the SST.

Raise the ring gear side of the differential case slightly to remove the ring gear tooth side case bearing outer race.

Remove the differential case from the differential carrier.

• NOTICE:

• Do not damage the case bearing.