Lexus IS250 IS220d GSE20 ALE20 - MULTIPLEX COMMUNICATION

SYSTEM DESCRIPTION

WIRING DIAGRAM

INSPECTION PROCEDURE

INSPECT FUSE (FR P/SEAT RH(LHD), FR P/SEAT LH (RHD), MPX-B)

CHECK WIRE HARNESS (POSITION CONTROL ECU AND SWITCH - BATTERY AND BODY GROUND)

CHECK RESISTANCE OF COMMUNICATION LINE

DTC B1289 Passenger Seat ECU Communication Stop

SYSTEM DESCRIPTION

This DTC is detected when communication between the position control ECU and switch (passenger ECU) and gateway ECU stops for more than 10 seconds.

DTC No.DTC Detection ConditionTrouble Area
B1289Position control ECU and switch (passenger seat ECU) communication stops
Position control ECU and switch (passenger seat ECU)
Wire harness

WIRING DIAGRAM

Dtc B1289 Passenger Seat Ecu Communication Stop. MULTIPLEX COMMUNICATION. Lexus IS250 IS220d GSE20 ALE20

Dtc B1289 Passenger Seat Ecu Communication Stop. MULTIPLEX COMMUNICATION. Lexus IS250 IS220d GSE20 ALE20

INSPECTION PROCEDURE

  • HINT:
  • When "+B of GND short malfunction of communication bus" DTCs (B1214 and B1215) are detected at the same time as "communication stop" DTC B1289, repair the "+B or GND short malfunction of communication bus" DTCs first.
1.INSPECT FUSE (FR P/SEAT RH(LHD), FR P/SEAT LH (RHD), MPX-B)

Remove the FR P/SEAT RH fuse from the cowl side J/B RH (for LHD).

Remove the FR P/SEAT LH fuse from the cowl side J/B LH (for RHD).

Remove the MPX-B fuse from engine room J/B No. 1.

Measure the resistance of the fuse.

  • Standard resistance:
  • Below 1 Ω
NG
REPLACE FUSE
OK
2.CHECK WIRE HARNESS (POSITION CONTROL ECU AND SWITCH - BATTERY AND BODY GROUND)

Disconnect the T6 and T7 ECU connectors (for LHD).

Dtc B1289 Passenger Seat Ecu Communication Stop. MULTIPLEX COMMUNICATION. Lexus IS250 IS220d GSE20 ALE20

Disconnect the U6 and U7 ECU connectors (for RHD).

Measure the voltage and resistance of the wire harness side connector.

  • Standard voltage:
  • Tester ConnectionConditionSpecified Condition
    *1+B (T6-5) - Body ground
    *2+B (U6-5) - Body ground    		Always10 to 14 V
    *1SYSB (T7-8) - Body ground
    *2SYSB (U7-8) - Body ground    		Always10 to 14 V
  • Standard resistance:
  • Tester ConnectionSpecified Condition
    *1GND (T6-1) - Body ground
    *2GND (U6-1) - Body ground    		Below 1 Ω
  • HINT:
*1: LHD
*2: RHD
NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK
3.CHECK RESISTANCE OF COMMUNICATION LINE

Disconnect the T7, RJ and P33 ECU connectors (for LHD).

Disconnect the U7, 2F and J55 ECU connectors (for RHD).

Dtc B1289 Passenger Seat Ecu Communication Stop. MULTIPLEX COMMUNICATION. Lexus IS250 IS220d GSE20 ALE20

Measure the resistance between the specified terminals on the wire harness side connectors.

  • Standard resistance:
  • Tester ConnectionSpecified Condition
    *1MPX1 (T7-1) - MPX1 (L17-7)
    *2MPX1 (U7-1) - 2F-5    		Below 1 Ω
    *1MPX1 (T7-1) - MPX1 (P33-27)
    *2MPX1 (U7-1) - MPX2 (J55-24)    		Below 1 Ω
  • HINT:
*1: LHD
*2: RHD
  • Result:
  • ResultProceed to
    Both are OKA
    One is OKB
    Both are NGC
B
REPAIR OR REPLACE HARNESS OR CONNECTOR AND REPLACE POSITION CONTROL ECU
C
REPAIR OR REPLACE HARNESS OR CONNECTOR
A
REPLACE POSITION CONTROL ECU AND SWITCH
LEXUS IS250, IS220d / GSE20 ALE20
MULTIPLEX COMMUNICATION
Lexus IS250 IS220d GSE20 ALE20
MULTIPLEX COMMUNICATION SYSTEM