Lexus IS250 IS220d GSE20 ALE20 - BRAKE CONTROL
CHECK HARNESS AND CONNECTOR (MOMENTARY INTERRUPTION)
CHECK IF EACH SENSOR AND ECM CONNECTOR IS SECURELY CONNECTED
REPAIR OR REPLACE HARNESS OR CONNECTOR
DTC U0073/94 Control Module Communication Bus OFF
DTC U0100/65 Lost Communication with ECM / PCM
DTC U0123/62 Lost Communication with Yaw Rate Sensor Module
DTC U0124/95 Lost Communication with Lateral Acceleration Sensor Module
DTC U0126/63 Lost Communication with Steering Angle Sensor Module
DESCRIPTION
The skid control ECU inputs the signals from the ECM, steering angle sensor, and yaw rate and acceleration sensor via CAN communication system.
DTC No. | DTC Detection Condition | Trouble Area |
U0073/94 | When any of the following is detected: After the output of data from the skid control ECU is completed, the sending continues for 5 seconds or more. The condition that bus OFF state occurs once or more within 100 ms occurs 10 times in succession. (Sent signals cannot be received.) With the IG1 terminal voltage 10 V or more, a delay in receiving data from the yaw rate and acceleration sensor and steering angle sensor continues for 1 second or more. With the IG1 terminal voltage 10 V or more, the condition that a delay in receiving data from the yaw rate and acceleration sensor occurs more than once within 5 seconds occurs 10 times in succession. | CAN communication system |
U0100/65 | When either of the following is detected: With the IG1 terminal voltage 10 V or more and the vehicle speed 9 mph (15 km/h) or more, data cannot be sent to the ECM for 2 seconds or more. With the IG1 terminal voltage 10 V or more and the vehicle speed 9 mph (15 km/h) or more, data from the ECM cannot be received for 2 seconds or more. | CAN communication system (Skid control ECU to ECM) |
U0123/62 | When either of the following is detected: With the IG1 terminal voltage 10 V or more, data from the yaw rate sensor cannot be received for 1 second or more. With the IG1 terminal voltage 10 V or more, the following occurs 10 times in succession within 60 seconds. The condition that data from the yaw rate sensor cannot be received occurs once or more within 5 seconds. | CAN communication system (Skid control ECU to yaw rate and acceleration sensor) |
U0124/95 | When either of the following is detected: With the IG1 terminal voltage 10 V or more, data from the acceleration sensor cannot be received for 1 second or more. With the IG1 terminal voltage 10 V or more, the following occurs 10 times in succession within 60 seconds. The condition that data from the acceleration sensor cannot be received occurs once or more within 5 seconds. | CAN communication system (Skid control ECU to yaw rate and acceleration sensor) |
U0126/63 | When either of the following is detected: With the IG1 terminal voltage 10 V or more, data from the steering angle sensor cannot be received for 1 second or more. With the IG1 terminal voltage 10 V or more, the following occurs 10 times in succession within 60 seconds. The condition that data from the steering angle sensor cannot be received occurs once or more within 5 seconds. | CAN communication system (Skid control ECU to steering angle sensor) |
WIRING DIAGRAM
INSPECTION PROCEDURE
1.CHECK HARNESS AND CONNECTOR (MOMENTARY INTERRUPTION) |
Using the intelligent tester, check for any momentary interruption in the wire harness and connector corresponding to a DTC .
Item (Display) | Measurement Item / Range (Display) | Normal Condition |
EFI Communication Open | EFI communication open detection / ERROR or NORMAL | ERROR: Momentary interruption NORMAL: Normal |
Steering Open | Steering sensor open detection / ERROR or NORMAL | ERROR: Momentary interruption NORMAL: Normal |
Yaw Rate Open | Yaw rate sensor open detection / ERROR or NORMAL | ERROR: Momentary interruption NORMAL: Normal |
- Result:
Condition Proceed to There is a constant open circuit A There are no momentary interruptions B There are momentary interruptions C
- HINT:
- Perform the above inspection before removing the sensor and connector.
|
| ||||
|
| ||||
A | |
2.CHECK IF EACH SENSOR AND ECM CONNECTOR IS SECURELY CONNECTED |
Check if each sensor or ECM connector is securely connected.
- OK:
- The connector should be securely connected.
|
| ||||
OK | |
3.RECONFIRM DTC |
Record the output DTCs (for ABS, VSC, and CAN communication) .
- HINT:
- If the CAN communication system DTC and the relevant sensor DTCs are output simultaneously, troubleshoot the relevant sensor DTCs (for ABS and VSC) after the CAN communication system returns to normal.
- Result:
Condition Proceed to DTC (CAN communication system DTC) is output A DTC (ABS and/or VSC DTC) is output B DTC is not output C
|
| ||||
|
| ||||
A | ||
|
4.REPAIR OR REPLACE HARNESS OR CONNECTOR |
Repair or replace the harness or connector.
Check for any momentary interruption between the skid control ECU and each sensor or ECM .
Check that there is no momentary interruption.
NEXT | |
5.RECONFIRM DTC |
Clear the DTC .
Start the engine.
Drive the vehicle and turn the steering wheel to the right and left at a speed of 9 mph (15 km/h) or more.
Check that no CAN communication system DTC is output.
If ABS and VSC DTCs are output, record them.
- Result:
Condition Proceed to DTC is output for the CAN communication system A No DTC is output (ABS and/or VSC DTC is output) B No DTC is output (No ABS and/or VSC DTC is output) C
- HINT:
- The CAN communication system must be normal when repairing each sensor DTC (for ABS and VSC).
|
| ||||
|
| ||||
A | ||
|