INSTALL BRAKE MASTER CYLINDER SUB-ASSEMBLY

CONNECT CLUTCH RESERVOIR HOSE (for Manual Transmission)

INSTALL NO. 3 ENGINE ROOM RELAY BLOCK

FILL RESERVOIR WITH BRAKE FLUID

BLEED MASTER CYLINDER

BLEED BRAKE LINE

BLEED BRAKE ACTUATOR ASSEMBLY

BLEED AIR FROM CLUTCH LINE (for Manual Transmission)

INSPECT FLUID LEVEL IN RESERVOIR

INSPECT FOR BRAKE FLUID LEAKAGE

INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY

INSTALL WINDSHIELD WIPER ARM AND BLADE ASSEMBLY RH

INSTALL WINDSHIELD WIPER ARM AND BLADE ASSEMBLY LH

INSTALL FRONT WIPER ARM HEAD CAP

INSTALL ROOF DRIP SIDE FINISH MOULDING RH

INSTALL ROOF DRIP SIDE FINISH MOULDING LH

INSTALL FRONT UPPER FENDER PROTECTOR LH

INSTALL FRONT UPPER FENDER PROTECTOR RH

INSTALL ENGINE ROOM SIDE COVER RH

INSTALL ENGINE ROOM SIDE COVER LH

INSTALL COOL AIR INTAKE DUCT SEAL

Install a new O-ring to the brake master cylinder sub-assembly.

Install the brake master cylinder sub-assembly to the booster assembly with the 2 nuts.

• Torque:
• 12.5 N*m{ 127 kgf*cm, 9 ft.*lbf}

Install the brake actuator assembly to the actuator bracket with the 2 cap nuts.

• Torque:
• 5.5 N*m{ 55 kgf*cm, 48 in.*lbf}

Using SST, connect the 2 brake lines to the brake master cylinder sub-assembly.

• SST
• 09023-00101

• Torque:
• 15 N*m{ 155 kgf*cm, 11 ft.*lbf}

Engage the clamp and connect the warning switch connector.

Connect the clutch reservoir hose with the clamp.

Install the No. 3 engine room relay block with the bolt and nut.

• Torque:
• 12.5 N*m{ 127 kgf*cm, 9 ft.*lbf}

Fill the reservoir with brake fluid.

• Fluid:
• SAE J1703 or FMVSS No. 116 DOT3

Disconnect the 2 brake lines from the master cylinder.

Slowly depress the brake pedal and hold it (*1).

Cover the 2 outer holes with fingers, and release the brake pedal (*2).

Repeat (*1) and (*2) 3 or 4 times.

Using SST, connect the brake lines to the master cylinder.

• SST
• 09023-00101

• Torque:
• 15 N*m{ 155 kgf*cm, 11 ft.*lbf}

Connect the vinyl tube to the bleeder plug.

Depress the brake pedal several times, then loosen the bleeder plug with the pedal depressed (*3).

When fluid no longer comes out, tighten the bleeder plug, then release the brake pedal (*4).

Repeat (*3) and (*4) until all the air in the fluid is completely bled out.

Using SST, tighten the bleeder plug completely.

• SST
• 09023-00101

• Torque:
• 11 N*m{ 110 kgf*cm, 8 ft.*lbf}

Repeat the above procedures for each wheel to bleed the air from the brake line.

Depress the brake pedal more than 20 times with the engine switch off.

Connect the intelligent tester to the DLC3, then turn the engine switch on (IG).

• NOTICE:

• Do not start the engine.

Turn the intelligent tester power on and select "AIR BLEEDING" on the screen.

• NOTICE:

Bleed the air from the actuator according to "Step 1: Increase" on the intelligent tester display.

• NOTICE:

• Make sure that the master cylinder reservoir tank does not become empty of brake fluid.

Connect a vinyl tube to either one of the bleeder plugs.

Depress the brake pedal several times, then loosen the bleeder plug connected to the vinyl tube with the pedal depressed (*5).

When fluid no longer comes out, tighten the bleeder plug, then release the brake pedal (*6).

Repeat (*5) and (*6) until all the air in the fluid is completely bled.

Using SST, tighten the bleeder plug completely.

• SST
• 09023-00101

• Torque:
• 11 N*m{ 110 kgf*cm, 8 ft.*lbf}

Repeat the above procedures for the rest of the wheels to bleed the air from the brake lines.

Bleed the air from the suction line according to "Step 2: Inhalation" on the intelligent tester display.

• NOTICE:

Connect a vinyl tube to the bleeder plug at the right front wheel or the right rear wheel and loosen the bleeder plug.

Operate the brake actuator assembly to bleed the air using the intelligent tester (*7).

• NOTICE:

The operation stops automatically in 4 seconds.

At this time, be sure to release the brake pedal.

Check that the operation has stopped by referring to the intelligent tester display and tighten the bleeder plug (*8).

Repeat (*7) and (*8) until all the air in the fluid is completely bled out.

Using SST, tighten the bleeder plug completely.

• SST
• 09023-00101

• Torque:
• 11 N*m{ 110 kgf*cm, 8 ft.*lbf}

For the rest of the wheels, bleed the air in the same way as stated in the above procedures.

Bleed the air from the pressure reduction line according to "Step 3: Decrease" on the intelligent tester display.

• NOTICE:

Connect a vinyl tube to either one of the bleeder plugs.

Loosen the bleeder plug (*9).

Using the intelligent tester, operate the brake actuator assembly, completely depress the brake pedal and hold it.

• NOTICE:

The operation stops automatically after 4 seconds. When this operation will be repeated continuously, allow an interval of at least 20 seconds between each bleeding operation.

When the operation is completed, the brake pedal will go down slightly. This is a normal phenomenon due to the opening of the solenoid.

During this procedure, the brake pedal will seem heavy. It is necessary to completely depress it, so that brake fluid will come out of the bleeder plug.

Be sure to keep the brake pedal depressed. Never depress and release the pedal repeatedly.

Tighten the bleeder plug, then release the brake pedal (*10).

Repeat steps (*9) to (*10) until all the air in the fluid is completely bled out.

Using SST, tighten the bleeder plug completely.

• SST
• 09023-00101

• Torque:
• 11 N*m{ 110 kgf*cm, 8 ft.*lbf}

Repeat the above procedures for the rest of the brakes to bleed the air from the brake line.

Bleed the air from the brake line again according to "Step 4: Increase" on the intelligent tester display.

• NOTICE:

Connect a vinyl tube to either one of the bleeder plugs.

Depress the brake pedal several times, then loosen the bleeder plug connected to the vinyl tube with the pedal depressed (*11).

When fluid no longer comes out, tighten the bleeder plug, then release the brake pedal (*12).

Repeat (*11) and (*12) until all the air in the fluid is completely bled out.

Using SST, tighten the bleeder plug completely.

• SST
• 09023-00101

• Torque:
• 11 N*m{ 110 kgf*cm, 8 ft.*lbf}

Repeat the above procedures for each brake to bleed the air from the brake line.

Finish "AIR BLEEDING" on the intelligent tester and turn off the power.

Disconnect the intelligent tester from the DLC3.

Turn the engine switch off.

Remove the bleeder plug cap.

Connect a vinyl tube to the bleeder plug.

Depress the clutch pedal several times, and then loosen the bleeder plug with the pedal depressed.

When fluid no longer comes out, tighten the bleeder plug, and then release the clutch pedal.

Repeat the previous 2 steps until all the air in the fluid is completely bled.

Tighten the bleeder plug.

• Torque:
• 11 N*m{ 112 kgf*cm, 8 ft.*lbf}

Install the bleeder plug cap.

Check that all the air has been bled from the clutch line.

Check the fluid level and add fluid if necessary.

• Fluid:
• SAE J1703 or FMVSS No. 116 DOT3

• HINT:

• If fluid leaks, tighten or replace the leaking part.

Engage the 11 claws.

Install the cowl top ventilator louver sub-assembly with the 2 clips.

Operate the wiper, and stop the windshield wiper motor at the automatic stop position.

Clean the wiper arm serrations.

Clean the wiper pivot serrations with a wire brush (when reinstalling).

Install the front wiper arm and blade assembly RH with the nut at the position as shown in the illustration.

• Torque:
• 22 N*m{ 224 kgf*cm, 16 ft.*lbf}

• HINT:

• Hold the arm hinge by hand to fasten the nut.

Operate the front wipers while spraying washer fluid on the windshield glass. Make sure that the front wipers function properly and there is no interference with the vehicle body.

Operate the wiper, and stop the windshield wiper motor at the automatic stop position.

Clean the wiper arm serrations.

Clean the wiper pivot serrations with a wire brush (when reinstalling).

Install the front wiper arm and blade assembly LH with the nut at the position as shown in the illustration.

• Torque:
• 22 N*m{ 224 kgf*cm, 16 ft.*lbf}

• HINT:

• Hold the arm hinge by hand to fasten the nut.

Install the front wiper arm head cap.

• HINT:

• Use the same procedures for the RH side and the LH side.

Engage the claw and the 3 clips, then install the front upper fender protector LH.

Engage the clip on the rubber portion of the cowl top ventilator louver sub-assembly to the front fender protector upper LH.

Install the side cover with the 2 clips.

Install the side cover with the 5 clips.

Install the intake duct seal with the 11 clips.