Lexus IS250 IS220d GSE20 ALE20 - WINDSHIELD / WINDOWGLASS
POWER WINDOW REGULATOR MOTOR - REMOVAL
| 1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL |
| 2. REMOVE FRONT DOOR INSIDE HANDLE BEZEL PLUG |
Using a screwdriver wrapped with protective tape, disengage the 3 claws, and remove the front door inside handle bezel plug.
| 3. REMOVE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY |
Using a screwdriver wrapped with protective tape, disengage the 4 claws and the 2 clips.
Disconnect the connector and remove the power window regulator master switch assembly.
| 4. REMOVE COURTESY LIGHT ASSEMBLY |
Disengage the claw and remove the courtesy light assembly.
Disconnect the connector.
| 5. REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY |
Remove the 2 screws.
Using the clip remover, disengage the 9 clips.
Pull out the front door trim board in the direction indicated by the arrow.
Remove the reference bosses from the front door panel.
Raise the front door trim board to disengage the 4 claws and remove the front door trim board together with the front door inner glass weatherstrip.
Disconnect the cables and each connector from the back side of the inside handle and remove the front door trim board sub-assembly.
Remove the 2 front door trim board retainers (green) from the front door trim board.
| 6. REMOVE FRONT DOOR INNER GLASS WEATHERSTRIP |
Disengage the 4 clips as shown in the illustration and remove the front door inner glass weatherstrip from the front door trim board.
| 7. REMOVE FRONT DOOR SERVICE HOLE COVER |
Disconnect each connector and each clamp, and remove the front door service hole cover.
- HINT:
- Remove the remaining butyl tape on the door side.
| 8. REMOVE FRONT DOOR GLASS SUB-ASSEMBLY |
Remove the hole plug.
Connect the power window regulator master switch assembly and move the front door glass sub-assembly so that the door glass bolts can be seen.
Remove the 2 bolts.
- NOTICE:
- After the bolts are removed, the door glass may fall and become deformed.
Remove the front door glass sub-assembly as shown in the illustration.
- NOTICE:
- Do not damage the door glass.
Disconnect the power window regulator master switch assembly.
| 9. REMOVE FRONT DOOR WINDOW REGULATOR SUB-ASSEMBLY |
Disconnect the connector.
Loosen the temporary bolt.
- NOTICE:
- If the temporary bolt is removed, the front door window regulator may fall and become deformed.
Remove the 5 bolts.
Remove the front door window regulator sub-assembly and the power window regulator motor assembly front as a unit.
Remove the temporary bolt from the front door window regulator sub-assembly.
| 10. REMOVE FRONT POWER WINDOW REGULATOR MOTOR |
Using a "torx" socket wrench (T25), remove the 3 screws and the front power window regulator motor.
| 11. REMOVE REAR DOOR INSIDE HANDLE BEZEL PLUG |
Using a screwdriver wrapped with protective tape, disengage the 3 claws and remove the rear door inside handle bezel plug.
| 12. REMOVE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY |
Using a screwdriver wrapped with protective tape, disengage the 2 claws and 2 clips.
Disconnect the connector and remove the rear power window regulator switch assembly.
| 13. REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY |
Remove the 2 screws.
Using the clip remover, disengage the 8 clips.
Pull out the rear door trim board in the direction indicated by the arrow.
Remove the reference bosses from the rear door panel.
Raise the rear door trim board to disengage the 3 claws and remove the rear door trim board together with the rear door inner glass weatherstrip.
Disconnect the cables and each connector from the back side of the inside handle and the rear door trim board sub-assembly, remove the rear door trim board sub-assembly.
Remove the 2 rear door trim board retainers (green) from the rear door trim board.
| 14. REMOVE REAR DOOR INNER GLASS WEATHERSTRIP |
Disengage the 3 clips as shown in the illustration and remove the rear door inner glass weatherstrip from the rear door trim board.
| 15. REMOVE REAR DOOR SERVICE HOLE COVER |
Disconnect the connector and 2 clamps.
Remove the rear door service hole cover.
- HINT:
- Remove the remaining tape on the door side.
| 16. REMOVE REAR DOOR GLASS RUN |
Remove the rear door glass run.
| 17. REMOVE REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY |
Remove the 2 bolts, the screw, and the rear door window division bar sub-assembly.
| 18. REMOVE REAR DOOR QUARTER WINDOW GLASS |
Remove the rear door quarter window glass and the rear door quarter window weatherstrip as a unit as shown in the illustration.
Remove the rear door quarter window glass from the rear door quarter window weatherstrip.
| 19. REMOVE REAR DOOR GLASS SUB-ASSEMBLY |
Remove the rear door glass sub-assembly from the rear door window regulator sub-assembly as shown in the illustration.
- NOTICE:
- Do not damage the door glass.
| 20. REMOVE REAR DOOR WINDOW REGULATOR SUB-ASSEMBLY |
Disconnect the connector.
Loosen the temporary bolt.
- NOTICE:
- If the temporary bolt is removed, the rear door window regulator may fall and become deformed.
Remove the 3 bolts.
Remove the rear door window regulator sub-assembly and the power window regulator motor assembly rear as a unit.
Remove the temporary bolt from the rear door window regulator.
| 21. REMOVE REAR POWER WINDOW REGULATOR MOTOR |
Using a "torx" socket wrench (T25), remove the 3 screws and the rear power window regulator motor.