HOOD LOCK CONTROL CABLE ASSEMBLY - INSTALLATION

Disengage the 2 clamps and claw, and remove the hood hinge cover LH.

Disengage the 2 clamps, and remove the hood hinge cover RH.

Loosen the hood's 4 hinge bolts.

Move the hood and adjust the clearance between the hood and front fender.

Tighten the hood's 4 hinge bolts after the adjustment.

• Torque:
• 13 N*m{ 133 kgf*cm, 10 ft.*lbf}

Adjust the cushion rubber so that the height of the hood and fender are aligned.

• HINT:

• Raise or lower the hood's front end by turning the cushion rubber.

Using a screwdriver, remove the hood lock nut cap as shown in the illustration.

• HINT:

• Tape the screwdriver tip before use.

Loosen the 2 bolts and hood lock nut.

Tighten the bolts and nut after the adjustment.

• Torque:
• 8.0 N*m{ 82 kgf*cm, 71 in.*lbf}

Adjust the hood lock position so that the striker can enter it smoothly.

Install a new cap.

Check the tire pressure and adjust it if necessary.

Remove all excess weight from the vehicle (luggage, heavy objects, etc. ).

Remove dust, oil, and foreign matter from the radar sensor's level rack.

Set a level on the radar sensor's level rack.

Check that the air bubble is within the red frame on the level.

• OK:
• The air bubble is within the red frame on the level.
  If the bubble is not within the red frame, use a hexagon wrench to adjust screw A until the air bubble is within the red frame.

• HINT:

• Result:

• Adjustment Direction	Adjustment Procedure	Adjustment Angle
  Vertical adjustment	Upward direction: Turn screw A to negative (-) side Downward direction: Turn screw A to positive (+) side	Approx. 1.0° per turn

Adjust the reflector so that the center of the SST reflector is the same height as the millimeter wave radar sensor.

• SST
• 09870-60000(09870-60010,09870-60040)

• HINT:

• Prepare a 10 m (32.81 ft) string, a string with a sharp-pointed weight (plumb bob), and a 5 m (16.41 ft) tape measure.

Hang the string (with weight) from the center of the vehicle's rear emblem. Mark the vehicle's rear center point on the ground. Repeat the same procedure for the front of the vehicle.

Set one end of the 10 m (32.82 ft) string on the vehicle's rear center point. Run the string over the vehicle's front center point to a position 5 m (16.41 ft) beyond the vehicle front center point, as shown in the illustration. Mark the 5 m (16.41 ft) position.

Using a tape measure, measure 12 mm (0.47 in.) to the left of the 5 m (16.41 ft) position. Place the reflector at that position.

• NOTICE:

• Perform the operation as precisely as possible.

Connect the intelligent tester to the DLC3.

Turn the engine switch on (IG).

Turn the intelligent tester main switch on, and turn the cruise control main switch on.

• HINT:

• If an error message is displayed on the screen, initialization of the distance control ECU may not be completed. Initialize the distance control ECU

Check that the divergence of the radar beam axis is 0° .

• Standard:
• 0° (Both right and left)
• If the axis is not as specified, use a hexagon wrench to adjust screw B until the divergence of the radar beam axis is 0°.

Based on the measured divergence of the beam axis, turn and adjust screw B for horizontal adjustment of the millimeter wave radar sensor using a hexagon wrench.

• Result:

• Adjustment Direction	Adjustment Procedure	Adjustment Angle
  Horizontal adjustment	Right direction: Turn screw B to positive (+) side. Left direction: Turn screw B to negative (-) side.	Approx. 0.33° per turn

• HINT:

Reset the radar sensor's driving learning values. Prepare a type of metal that can block radio waves, such as aluminum foil. Cover the radar sensor's left half with the aluminum foil for 10 seconds.

• NOTICE:

• Be sure to keep the reflector in place and make sure that there is nothing between the sensor's left half and the reflector.

• HINT:

• When the reset is completed, the buzzer sounds for 10 seconds.

Disconnect the intelligent tester from the DLC3.

Set a level on the radar sensor's level rack.

Check that the air bubble is within the red frame on the level.

• OK:
• The air bubble is within the red frame on the level.
• If the bubble is not within the red frame, use a hexagon wrench to adjust screw A until the air bubble is within the red frame.

• HINT:

• Result:

• Adjustment Direction	Adjustment Procedure	Adjustment Angle
  Vertical adjustment	Upward direction: Turn screw A to negative (-) side Downward direction: Turn screw A to positive (+) side	Approx. 1.0°per turn

H Line (Fog light height):

Draw a horizontal line across the screen so that it passes through the center marks. The H line should be at the same height as the fog light bulb center marks of the low-beam fog lights.

V LH Line, V RH Line (Center mark position of left-hand (LH) and right-hand (RH) fog lights):

Draw two vertical lines so that they intersect the H line at each center mark.