If the seat position sensor has been dropped, or there are any cracks or other defects in the case, bracket or connector, replace the seat position sensor with a new one.

When installing the seat position sensor, make sure that the SRS wiring does not interfere with other parts and is not pinched between other parts.

Hold down the top of the sensor and tighten the sensor using a T30 "torx" socket.

Torque:
8.0 N*m{ 82 kgf*cm, 71 in.*lbf}

Remove the feeler gauge.

Install the seat slide position sensor protector.

Connect the wire harness connector.

4. INSTALL SEAT CLIMATE CONTROL BLOWER (w/ Climate Control Seat System)

5. INSTALL SEAT CUSHION CLIMATE CONTROL DUCT (w/ Climate Control Seat System)

6. INSTALL SEATBACK CLIMATE CONTROL BLOWER (w/ Climate Control Seat System)

Using a T30 ''torx'' socket, install the blower cover and blower to the seat frame with the 6 ''torx'' bolts.

Connect the connector and attach the 3 clamps.

7. INSTALL LUMBAR SUPPORT ADJUSTER ASSEMBLY

Install the lumbar support adjuster with the 2 screws.

Connect the connector.

8. INSTALL FRONT LOWER SEAT CUSHION SHIELD

9. INSTALL FRONT LOWER SEAT CUSHION SHIELD LH

10. INSTALL RECLINING ADJUSTER INSIDE COVER LH

11. INSTALL SEAT RECLINING ADJUSTER INSIDE COVER LH

12. INSTALL RECLINING ADJUSTER INSIDE COVER LH

13. INSTALL LOWER RECLINING ADJUSTER INSIDE COVER RH

14. INSTALL FRONT SEAT BACK HEATER ASSEMBLY (w/ Seat Heater System)

Using a tacker, install the front seatback heater to the end of the seat cover with the 7 tack pins.

15. INSTALL FRONT SEPARATE TYPE SEATBACK COVER

Using hog ring pliers, install the seatback cover to the seatback pad with new hog rings.

16. INSTALL FRONT SEPARATE TYPE SEATBACK ASSEMBLY (w/o Seatback Board)

Fully cover the airbag with the 2 seatback cover brackets and tighten the nut.

Torque:
5.5 N*m{ 56 kgf*cm, 49 in.*lbf}

CAUTION:

For vehicles with side airbags, the seatback cover must be securely installed. Otherwise, the side airbags may not deploy properly.

Make sure that the strap is not twisted after installing the bracket.

Install the bracket securely.

Using hog ring pliers, install the seatback cover (with pad) to the seat frame with new hog rings, and attach the hooks.

Install the seatback cover (with pad) to the seat frame. (w/o Seatback Board)

17. INSTALL FRONT SEPARATE TYPE SEATBACK ASSEMBLY (w/ Seatback Board)

Fully cover the airbag with the 2 seatback cover brackets and tighten the nut.

Torque:
5.5 N*m{ 56 kgf*cm, 49 in.*lbf}

CAUTION:

For vehicles with side airbags, the seatback cover must be securely installed. Otherwise, the side airbags may not deploy properly.

Make sure that the strap is not twisted after installing the bracket.

Install the bracket securely.

Using hog ring pliers, install the seatback cover (with pad) to the seat frame with new hog rings.

Using hog ring pliers, install the seatback cover (with pad) to the seat frame with new hog rings, and attach the hooks.

Install the front seatback cover and attach the hooks.

18. INSTALL FRONT SEATBACK BOARD SUB-ASSEMBLY (w/ Seatback Board)

19. INSTALL FRONT SEAT HEADREST SUPPORT

20. INSTALL FRONT SEAT HEADREST SUPPORT

21. INSTALL FRONT SEAT CUSHION HEATER ASSEMBLY (w/ Seat Heater System)

Using a tacker, install the front seat cushion heater to the end of the seat cover with the 28 tack pins.

22. INSTALL FRONT SEPARATE TYPE SEAT CUSHION COVER

Using hog ring pliers, install the seat cushion cover to the seat cushion pad with new hog rings.

23. INSTALL FRONT SEPARATE TYPE SEAT CUSHION ASSEMBLY LH

24. INSTALL FRONT POWER SEAT SWITCH (w/ Seat Position Memory System)

Connect the 2 connectors.

Install the switch with the 3 screws.

25. INSTALL FRONT POWER SEAT SWITCH (w/o Seat Position Memory System)

Connect the connector.

Install the switch with the 3 screws.

26. INSTALL FRONT INNER SEAT CUSHION SHIELD

Attach the clip and 2 claws to install the cushion shield inner.

Install the screw.

27. INSTALL LOWER INNER SEAT TRACK SPACER

Install the spacer to the front cushion shield with the 2 screws.

28. INSTALL LOWER OUTER SEAT TRACK SPACER

Install the spacer to the front cushion shield with the 2 screws.

29. INSTALL FRONT POWER SEAT LUMBAR SWITCH

Install the switch to the front cushion shield with the 2 screws.

30. CONNECT INNER NO. 1 FRONT SEAT CUSHION SHIELD

Attach the claw and connect the No. 1 cushion shield inner to the front cushion shield.

Install the 2 screws.

31. INSTALL NO. 1 FRONT SEAT CUSHION SHIELD WITH CUSHION SHIELD INNER

Connect the connector to the lumbar front power seat switch.

Attach the claw and install the cushion shield with cushion shield inner.

Install the 5 screws.

Install the 2 rubber bands of the front seatback board to the seat frame.

Connect the connector to the No. 1 interior illumination light.

32. INSTALL RECLINING POWER SEAT SWITCH KNOB

33. INSTALL SLIDE AND VERTICAL POWER SEAT SWITCH KNOB

34. INSTALL FRONT SEAT INNER BELT ASSEMBLY

Install the front seat inner belt assembly with the nut.

Torque:
42 N*m{ 428 kgf*cm, 31 ft.*lbf}

NOTICE:

Do not allow the anchor part of the front seat inner belt assembly to overlap the protruding parts of the front seat adjuster.

Connect the connector and attach the 4 clamps.

Front Seat Assembly (For Power Seat) - Reassembly. SEAT. Lexus IS250 IS220d GSE20 ALE20

LEXUS IS250, IS220d / GSE20 ALE20

SEAT

Lexus IS250 IS220d GSE20 ALE20

FRONT SEAT ASSEMBLY for Power Seat