Lexus IS250 IS220d GSE20 ALE20 - PARK ASSIST / MONITORING
ULTRASONIC SENSOR - REMOVAL
| 1. REMOVE COOL AIR INTAKE DUCT SEAL |
Using a clip remover, remove the 11 clips and cool air intake duct seal.
| 2. REMOVE FRONT BUMPER ASSEMBLY |
Using a screwdriver, turn the pin 90 degrees and remove the 2 pin hold clips.
- HINT:
Put protective tape around the front bumper assembly.
Using a clip remover, remove the 2 clips
Remove the 2 radiator grille protectors.
Remove the bolt and 10 screws.
Disengage the 5 claws and disconnect the front bumper assembly as shown in the illustration.
- HINT:
- Use the same procedures for the RH side and LH side.
Disconnect the headlight washer hose. (w/ headlight cleaner system)
Disconnect the connector and remove the front bumper assembly.
| 3. REMOVE NO. 1 ULTRASONIC SENSOR |
Disconnect the sensor connector.
Remove the sensor retainer as shown in the illustration.
Remove the No. 1 ultrasonic sensor from the front bumper.
| 4. REMOVE LUGGAGE COMPARTMENT TRIM COVER |
| 5. REMOVE DECK SIDE TRIM BOX LH |
| 6. REMOVE DECK SIDE TRIM BOX RH |
| 7. REMOVE SPARE WHEEL COVER |
| 8. REMOVE ROPE HOOK ASSEMBLY |
Remove the 3 bolts and 3 rope hook assemblies.
| 9. REMOVE REAR LUGGAGE COMPARTMENT TRIM COVER |
Using a clip remover, remove the 3 clips.
Disengage the 4 clips and remove the rear luggage compartment trim cover.
| 10. REMOVE ROOM LIGHT ASSEMBLY |
Disengage the claw and disconnect the No. 2 room light assembly.
Disconnect the connector and remove the No. 2 room light assembly.
| 11. REMOVE ROPE HOOK |
Remove the 2 rope hooks.
| 12. REMOVE FRONT LUGGAGE COMPARTMENT TRIM COVER |
Remove the 3 luggage compartment trim hooks as shown in the illustration.
Using a clip remover, remove the 2 clips.
Disengage the 4 claws and remove the front luggage compartment trim cover.
| 13. REMOVE LUGGAGE COMPARTMENT TRIM HOOK |
Remove the screw and No. 1 luggage compartment trim hook.
| 14. REMOVE SIDE LUGGAGE COMPARTMENT TRIM COVER |
Using a clip remover, remove the 3 clips and side luggage compartment trim cover LH.
| 15. DISCONNECT LUGGAGE ROOM WIRE |
Disconnect the No. 3 luggage room wire connector.
Disengage the grommet.
| 16. REMOVE REAR BUMPER PLATE |
Using a screwdriver, disengage the 2 claws and remove the No. 1 rear bumper plate.
- HINT:
| 17. REMOVE REAR BUMPER ASSEMBLY (for 4GR-FSE) |
Put protective tape around the rear bumper assembly.
Using a clip remover, remove the 2 clips.
Remove the 6 screws and 2 rear bumper seal brackets.
Disengage the 6 claws and disconnect the rear bumper assembly as shown in the illustration.
- HINT:
- Use the same procedures for the RH side and LH side.
Disengage the 4 claws and remove the rear bumper assembly as shown in the illustration.
| 18. REMOVE REAR BUMPER ASSEMBLY (for 2AD-FHV) |
Put protective tape around the rear bumper assembly.
Using a clip remover, remove the 2 clips.
Remove the 9 screws and 2 rear bumper seal brackets.
Disengage the 6 claws and disconnect the rear bumper assembly as shown in the illustration.
- HINT:
- Use the same procedures for the RH side and LH side.
Disengage the 4 claws and remove the rear bumper assembly as shown in the illustration.
| 19. REMOVE NO. 2 ULTRASONIC SENSOR |
Disconnect the sensor connector.
Remove the sensor retainer as shown in the illustration.
Remove the No. 2 ultrasonic sensor from the rear bumper.
| 20. REMOVE NO. 1 ULTRASONIC SENSOR |
Disconnect the sensor connector.
Remove the sensor retainer as shown in the illustration.
Remove the No. 1 ultrasonic sensor from the rear bumper.