REAR DOOR LOCK - INSPECTION

Remove the rear door lock assembly LH.

Measure the resistance according to the value(s) in the table below.

• Standard resistance:

• Tester Connection	Measurement Condition	Door Lock Condition	(Specified Condition)
  6 - 9 (*1)	Battery positive (+) → Terminal 2 Battery negative (-) → Terminal 1	Lock	10 kΩ or higher
  6 - 9 (*1)	Battery positive (+) → Terminal 1 Battery negative (-) → Terminal 2	Unlock	Below 1 Ω
  6 - 9 (*2)	Battery positive (+) → Terminal 4 Battery negative (-) → Terminal 1	Lock	10 kΩ or higher
  6 - 9 (*2)	Battery positive (+) → Terminal 1 Battery negative (-) → Terminal 4	Unlock	Below 1 Ω

*1: w/ Double locking system

*2: w/o Double locking system

Apply battery voltage and check operation of the door lock motor.

• OK:

• Measurement Condition	Specified Condition
  Battery positive (+) → Terminal 4 Battery negative (-) → Terminal 1 (*1)	Lock
  Battery positive (+) → Terminal 1 Battery negative (-) → Terminal 4 (*1)	Unlock
  Battery positive (+) → Terminal 2 Battery negative (-) → Terminal 1 (*2)	Lock
  Battery positive (+) → Terminal 1 Battery negative (-) → Terminal 2 (*2)	Unlock

*1: w/ Double locking system

*2: w/o Double locking system

Remove the rear door lock assembly LH.

Apply battery voltage and set the door lock motor to the lock position.

• OK:

• Measurement Condition	Specified Condition
  Battery positive (+) →Terminal 2 Battery negative (-) →Terminal 1	Lock

Apply battery voltage to the door lock and check operation of the double lock motor.

• OK:

• Measurement Condition	Specified Condition
  Battery positive (+) →Terminal 4 Battery negative (-) →Terminal 3	Double Locking System is set
  Battery positive (+) →Terminal 3 Battery negative (-) →Terminal 4	Double Locking System is unset

Measure the resistance according to the value(s) in the table below.

• Standard resistance:

• Tester Connection	Double Lock Position	Specified Condition
  9 - 10	Set	Below 1 Ω
  9 - 10	Unset	10 kΩ or higher

Remove the rear door lock assembly LH.

Apply battery voltage and set the door lock motor to the lock position.

• OK:

• Measurement Condition	Specified Condition
  Battery positive (+) →Terminal 2 Battery negative (-) →Terminal 1	Lock

Apply battery voltage to the door lock and check operation of the double lock motor.

• OK:

• Measurement Condition	Specified Condition
  Battery positive (+) →Terminal 4 Battery negative (-) →Terminal 3	Double Locking System is set
  Battery positive (+) →Terminal 3 Battery negative (-) →Terminal 4	Double Locking System is unset

Check that the doors cannot be unlocked by operating the control cable while the double locking system is set.

• OK:
• The doors cannot be unlocked.

Remove the rear door lock assembly RH.

Measure the resistance according to the value(s) in the table below.

• Standard resistance:

• Tester Connection	Measurement Condition	Door Lock Condition	(Specified Condition)
  9 - 10 (*1)	Battery positive (+) → Terminal 4 Battery negative (-) → Terminal 1	Lock	10 kΩ or higher
  9 - 10 (*1)	Battery positive (+) → Terminal 1 Battery negative (-) → Terminal 4	Unlock	Below 1 Ω
  6 - 9 (*2)	Battery positive (+) → Terminal 4 Battery negative (-) → Terminal 1	Lock	10 kΩ or higher
  6 - 9 (*2)	Battery positive (+) → Terminal 1 Battery negative (-) → Terminal 4	Unlock	Below 1 Ω

*1: w/ Double locking system

*2: w/o Double locking system

Remove the rear lock assembly RH.

Apply battery voltage and check operation of the door lock motor.

• OK:

• Measurement Condition	Specified Condition
  Battery positive (+) → Terminal 4 Battery negative (-) → Terminal 3 (*1)	Lock
  Battery positive (+) → Terminal 3 Battery negative (-) → Terminal 4 (*1)	Unlock
  Battery positive (+) → Terminal 4 Battery negative (-) → Terminal 1 (*2)	Lock
  Battery positive (+) → Terminal 1 Battery negative (-) → Terminal 4 (*2)	Unlock

*1: w/ Double locking system

*2: w/o Double locking system

Apply battery voltage and set the door lock motor to the lock position.

• OK:

• Measurement Condition	Specified Condition
  Battery positive (+) →Terminal 4 Battery negative (-) →Terminal 3	Lock

Apply battery voltage to the door lock and check operation of the double lock motor.

• OK:

• Measurement Condition	Specified Condition
  Battery positive (+) →Terminal 2 Battery negative (-) →Terminal 1	Double Locking System is set
  Battery positive (+) →Terminal 1 Battery negative (-) →Terminal 2	Double Locking System is unset

Measure the resistance according to the value(s) in the table below.

• Standard resistance:

• Tester Connection	Double Lock Position	Specified Condition
  5 - 6	Set	Below 1 Ω
  5 - 6	Unset	10 kΩ or higher

Apply battery voltage and set the door lock motor to the lock position.

• OK:

• Measurement Condition	Specified Condition
  Battery positive (+) →Terminal 4 Battery negative (-) →Terminal 3	Lock

Apply battery voltage to the door lock and check operation of the double lock motor.

• OK:

• Measurement Condition	Specified Condition
  Battery positive (+) →Terminal 2 Battery negative (-) →Terminal 1	Double Locking System is Set
  Battery positive (+) →Terminal 1 Battery negative (-) →Terminal 2	Double Locking System is Unset

heck that the doors cannot be unlocked by operating the control cable while the double locking system is set.

• OK:
• The doors cannot be unlocked.