Lexus IS250 IS220d GSE20 ALE20 - DOOR LOCK
POWER DOOR LOCK CONTROL SYSTEM - OPERATION CHECK
| CHECK ELECTRICAL DOOR LOCK OPERATION |
- NOTICE:
- The initial condition that the customizing function using the intelligent tester is not chosen is shown.
Check the basic function.
Check that all doors lock when the door control switch (for manual operation) is turned to LOCK and all doors unlock when turned to UNLOCK.
Check that all doors lock when the driver side door lock key cylinder is turned to LOCK using the mechanical key.
Check the electrical key lock-in prevention function.
- NOTICE:
- In order to prevent the electrical key from being actually locked-in, the following inspection should be performed with the driver side door window open.
Place the electrical key inserted in the cabin.
With the driver side door open, check that all doors unlock immediately after the door lock knob for the driver side door is turned to LOCK.
With the driver side door open, check that all doors unlock immediately after the door control switch (for manual operation) is turned to LOCK.
With the driver side door open, turn the driver side door lock knob to LOCK and hold it for 2 seconds or more, and then close the driver side door. Then check that all doors unlock.
Check the security function.
Close all doors with the driver side door window open so that the door control switch can be operated from outside the vehicle.
Pull out the electrical key, open the driver side door and then close and lock the door using the electrical key. Under this condition, check that all doors do not unlock when the door control switch (for manual operation) is turned to UNLOCK from outside the vehicle.
Pull out the electrical key and the mechanical key, and close and lock the driver side door by mechanical key operation. Under this condition, check that all doors do not unlock when the door control switch (for manual operation) is turned to UNLOCK from outside the vehicle.
Pull out the electrical key, close the driver side door, and lock the door by wireless door lock operation. Under this condition, check that all doors do not unlock when the door control switch (for manual operation) is turned to UNLOCK from outside the vehicle.
- HINT:
- Check that the security function is canceled under the following conditions:
Check the illumination function.
Set the room light switch to the DOOR position.
With all doors locked, check that all doors unlock when the driver side door lock cylinder is turned to UNLOCK using the key. At the same time, the room light and the foot light come on.
Check that the room light and the foot light go off in approximately 15 seconds if the doors have not been opened.
Check the AUTO lock function.
Lock all doors.
Unlock all doors using the electrical key.
Allow 30 seconds to elapse while all doors remain closed and the electrical key switch and the entry unlock switch remain untouched. Then, check that all doors will lock automatically.
| CHECK DOUBLE LOCKING FUNCTION SYSTEM |
Check that the double locking system is set.
Open all the windows.
Turn the engine switch off and remove the key.
Open and close the driver side door, and make sure that all doors and the back door are closed securely.
Push the LOCK switch on the wireless transmitter or electrical key twice within 5 seconds, and check that the hazard warning lights flash once at this time to show that the system is set.
Try to unlock all doors by the inside handle of the vehicle, and check that none of the doors is unlocked.
- NOTICE:
Check that the double locking system is canceled.
Push the UNLOCK switch on the wireless transmitter while the double locking system is set.
Check that the doors can be opened both by the inside handle and the outside handle.
- NOTICE:
- If the battery of the wireless transmitter is dead, only the driver side door can be opened using the key. However, the theft deterrent system still remains on. Therefore, be careful that the theft alarm is set off when the door is opened without using the wireless transmitter.
Double Locking System Set Control Timing Chart.
Double Locking System Unset Control Timing Chart.
| CHECK THE FAIL-SAFE FOR THE DOUBLE LOCKING SYSTEM |
The double lock control ECU will set the double locking system to OFF if there is a door in which the system is ON when either of the following conditions is met. When the system is set to OFF, the door enters the ordinary locked state.
The engine switch on (IG).
If any of the double lock position switches are not in the UNSET position after the double locking system has been set to OFF, the double door lock ECU will try to set the system to OFF again 1 second later (retry function).
- HINT:
If the double door lock ECU judges that a malfunction is caused by the BEAN, the system enters the following states until the ECU determines that the system is normal.
The double locking system does not respond to the requests from the main body ECU RH (the system does not turn ON and OFF).
The double door lock ECU does not set the double locking system to OFF even when the condition indicated by step [*1] is met.