Meter / Gauge System - Customize Parameters

Lexus IS250 IS220d GSE20 ALE20 - METER


METER / GAUGE SYSTEM - CUSTOMIZE PARAMETERS

Combination Meter Assembly

*1: RHD except for Cypriot and Irish
*2: for LHD and RHD for Cypriot and Irish
*3: RHD for Cypriot and Irish
*4: for LHD

  • NOTICE:
Be sure to record the current value before customizing.
  • HINT:
  • The following items can be customized using the intelligent tester.
METER:
Display (Item)DefaultContentsSetting
Key Remained VolumeLargeFunction to change the volume of the key remind warning buzzerLarge, Medium, Small
Key Remained SoundNormalFunction to change the cycle of the key remind warning buzzerFast, Normal, Slow
Units by RegionML/G (*1)
KM/L (*2)		Function to change the unit of the trip information displayML/G, ML/G, KM/L
  • HINT:
  • The following items can be customized without using the intelligent tester.
ItemDefaultContentsSetting
Seat belt warning buzzer (See procedure "A")b-onFunction to change the volume of the seat belt warning buzzerb-on, b-oFF
Speed indicator (See procedure "B")75 (mph) (*1)
120 (km/h) (*3)
130 (km/h) (*4)		Function to change the value that decides the speed indicator when to illuminate30 to 100 (mph) (*1)
50 to 160 (km/h) (*3)
50 to 200 (km/h) (*4)
Tach indicator (See procedure "B")5,000 (rpm) (*5)
4,000 (rpm) (*6)		Function to change the value that decides the tach indicator when to illuminate2,000 to 6,500 (rpm)
2,000 to 5,100 (rpm)
Seat Belt Buzzer ON/OFF setting (Procedure "A")

The seat belt buzzer ON/OFF setting, which is a setting of the buzzer function of the combination meter, can disable the driver and front passenger side seat belt buzzers.

  • NOTICE:
These buzzers should be on for safe driving. Perform these procedures only if it is necessary to set the buzzer off (disabled).
When either the battery cable or the combination meter connector is disconnected, these buzzers are set on (enabled).
Odometer returns to 0 after starting this procedure, although it is not displayed.
  • HINT:
  • "b-oFF" indicates that the seat belt buzzer is OFF. "b-on" indicates that the buzzer is ON. The buzzer ON/OFF setting will be finished (the odometer will display "ODO") if the ODO/TRIP switch is not operated for 10 seconds or more. In this case, perform step 11 to check that the buzzer ON/OFF setting is complete. If it is not complete, start from step 1 again.

Driver and front passenger side seat belt buzzers

Turn the engine switch on (IG).

Press the ODO/TRIP switch until the odometer displays "ODO".

Turn the engine switch off.

Turn the engine switch on (IG).

Press the ODO/TRIP switch immediately (within 6 seconds) and hold it down for 10 seconds or more.

Continue holding down the ODO/TRIP switch and fasten the driver side seat belt.

Check that the odometer displays either "b-on" or "b-oFF".

Press the ODO/TRIP switch to change the display to "b-oFF".

Turn the engine switch off.

Turn the engine switch on (IG).

Check that no buzzer sounds.

Front passenger side seat belt buzzer

Turn the engine switch on (IG).

Press the ODO/TRIP switch until the odometer displays "ODO".

Turn the engine switch off.

Turn the engine switch on (IG).

Sit in the front passenger seat. Press the ODO/TRIP switch immediately (within 6 seconds) and hold it down for 10 seconds or more.

Sit in the front passenger seat. Continue holding down the ODO/TRIP switch and fasten the front passenger side seat belt.

Check that the odometer displays either "b-on" or "b-oFF".

Press the ODO/TRIP switch to change the display to "b-oFF".

Turn the engine switch off.

Turn the engine switch on (IG).

Check that no buzzer sounds.

SPEED AND TACH INDICATOR (Procedure "B")
Meter / Gauge System - Customize Parameters. METER. Lexus IS250 IS220d GSE20 ALE20

Select the SPEED INDICATOR or TACH INDICATOR using the satellite switch (RH, ON/OFF, or LH switch).

Turn the SPEED INDICATOR or TACH INDICATOR function off by using the ON/OFF switch.

Turn the SPEED INDICATOR or TACH INDICATOR function on again by using the ON/OFF switch.

Meter / Gauge System - Customize Parameters. METER. Lexus IS250 IS220d GSE20 ALE20

Leave the display on for 1 second to allow it to change to the SET display.

When SET flashes, the speedometer needle moves to indicate the previously set vehicle speed and then stops.

Meter / Gauge System - Customize Parameters. METER. Lexus IS250 IS220d GSE20 ALE20

Push the LH or RH switch within 6 seconds of the speedometer needle moving in order to allow setting of the speedometer indicator set point.

The speedometer needle moves by 1 degree each time the LH or RH switch is pushed.
Pushing and holding the switch changes values at a faster rate.
Unless operating the LH, RH or ON/OFF switch within 6 seconds, the indicator setting mode finishes and the SPEED/TACH indicator setting returns to previous value.

When the ON/OFF switch is pushed, the speedometer or tachometer needle stays at the setting value for 1 second, the buzzer sounds once, and the SPEED indicator illuminates only momentarily one time in yellow.