DESCRIPTION
WIRING DIAGRAM
INSPECTION PROCEDURE
PERFORM ACTIVE TEST BY INTELLIGENT TESTER
INSPECT SCUFF PLATE LIGHT (FRONT LH)
CHECK HARNESS AND CONNECTOR (SCUFF PLATE LIGHT - BODY GROUND)
CHECK HARNESS AND CONNECTOR (MAIN BODY ECU LH - SCUFF PLATE LIGHT)
INSPECT SCUFF PLATE LIGHT (FRONT RH)
CHECK HARNESS AND CONNECTOR (SCUFF PLATE LIGHT - BODY GROUND)
CHECK HARNESS AND CONNECTOR (MAIN BODY ECU LH - SCUFF PLATE LIGHT)
CHECK HARNESS AND CONNECTOR (POWER SOURCE OF SCUFF PLATE LIGHT)
LIGHTING SYSTEM - Scuff Plate Light Circuit
DESCRIPTION
The operation timing of the scuff plate lights is the same as that of the front and rear interior lights.
The scuff plate lights turn on when a door is opened, and turn off when the door is closed. This illumination setting can be canceled using the overhead J/B switch.
In addition, the scuff plate lights blink while the theft deterrent system is sounding an alarm.
The turning on and off of the scuff plate lights is controlled by the main body ECU LH based on various signals received through BEAN communication.
The main body ECU LH includes a MOS-FET (Metal Oxide Semiconductor - Field Effect Transistor) circuit that fades the scuff plate lights in and out by duty control.
This MOS-FET circuit has an overheat protection function as a fail-safe. If the main body ECU LH becomes excessively hot, the scuff plate lights turn off and remain off.
Normal operation will resume when the conditions required to turn on the scuff plate lights are met again.
WIRING DIAGRAM
INSPECTION PROCEDURE
| 1.PERFORM ACTIVE TEST BY INTELLIGENT TESTER |
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).
Turn the intelligent tester on.
Select the item(s) below in the ACTIVE TEST, and check the operation.
ACTIVE TEST: Body No. 3 (Main Body ECU LH)| Item | Test Details | Diagnostic Note |
| Interior Light Operation |
Interior light ON / OFF | - |
- OK:
- The scuff plate light LH and RH come on.
- Result:
| Result | Proceed to |
| Scuff plate light LH does not come on | A |
| Scuff plate light RH does not come on | B |
| Neither LH nor RH light comes on | C |
| OK | D |
| |
|
| |
|
| | PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE |
|
|
| 2.INSPECT SCUFF PLATE LIGHT (FRONT LH) |
Remove the scuff plate light.
Connect the (+) lead from the battery to terminal 2 and the (-) lead to terminal 1, and then check that the scuff plate light comes on.
- OK:
- The scuff plate light comes on.
| | REPLACE SCUFF PLATE LIGHT |
|
|
| 3.CHECK HARNESS AND CONNECTOR (SCUFF PLATE LIGHT - BODY GROUND) |
Disconnect the Q8 scuff plate light connector.
Measure the voltage according to the value(s) in the table below.
- Standard voltage:
| Tester Connection | Condition | Specified Condition |
| Q8-2 (+) - Body ground | Always | 10 to 14 V |
| | REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|
| 4.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU LH - SCUFF PLATE LIGHT) |
Disconnect the Q8 scuff plate light connector.
Disconnect the LA main body ECU LH connector.
Measure the resistance according to the value(s) in the table below.
- Standard resistance:
| Tester Connection | Condition | Specified Condition |
| LA-19 (ILE1) - Q8-1 (-) | Always | Below 1 Ω |
| LA-19 (ILE1) - Body ground | Always | 10 kΩ or higher |
| | REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|
| OK | |
| |
| REPLACE MAIN BODY ECU LH (COWL SIDE J/B LH) |
|
| 5.INSPECT SCUFF PLATE LIGHT (FRONT RH) |
Remove the scuff plate light.
Connect the (+) lead from the battery to terminal 2 and the (-) lead to terminal 1, and then check that the scuff plate light comes on.
- OK:
- The scuff plate light comes on.
| | REPLACE SCUFF PLATE LIGHT |
|
|
| 6.CHECK HARNESS AND CONNECTOR (SCUFF PLATE LIGHT - BODY GROUND) |
Disconnect the P2 scuff plate light connector.
Measure the voltage according to the value(s) in the table below.
- Standard voltage:
| Tester Connection | Condition | Specified Condition |
| P2-2 (+) - Body ground | Always | 10 to 14 V |
| | REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|
| 7.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU LH - SCUFF PLATE LIGHT) |
Disconnect the P2 scuff plate light connector.
Disconnect the LA main body ECU LH connector.
Measure the resistance according to the value(s) in the table below.
- Standard resistance:
| Tester Connection | Condition | Specified Condition |
| LA-19 (ILE1) - P2-1 (-) | Always | Below 1 Ω |
| LA-19 (ILE1) - Body ground | Always | 10 kΩ or higher |
| | REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|
| OK | |
| |
| REPLACE MAIN BODY ECU LH (COWL SIDE J/B LH) |
|
| 8.CHECK HARNESS AND CONNECTOR (POWER SOURCE OF SCUFF PLATE LIGHT) |
If neither of the scuff plate lights comes on as a result of the ACTIVE TEST, there may be problems in the power source and main body ECU LH.
Perform the following inspection on either the LH or RH side.
Disconnect the Q8 or P2 scuff plate light connector.
Measure the voltage according to the value(s) in the table below.
- Standard voltage:
- Front Door RH:
| Tester Connection | Condition | Specified Condition |
| Q8-2 (+) - Body ground | Always | 10 to 14 V |
- Front Door LH:
| Tester Connection | Condition | Specified Condition |
| P2-2 (+) - Body ground | Always | 10 to 14 V |
| | REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|
| OK | |
| |
| REPLACE MAIN BODY ECU LH (COWL SIDE J/B LH) |
|
