Lexus IS250 IS220d GSE20 ALE20 - WIPER AND WASHER
FRONT WASHER MOTOR - INSTALLATION
| 1. INSTALL HEADLIGHT CLEANER MOTOR AND PUMP ASSEMBLY (w/ Headlight Cleaner System) |
Install the headlight cleaner motor and pump assembly.
| 2. INSTALL WINDSHIELD WASHER MOTOR AND PUMP ASSEMBLY |
Install the windshield washer motor and pump assembly.
| 3. INSTALL WINDSHIELD WASHER JAR AND PUMP ASSEMBLY (w/o Headlight Cleaner System) |
Install the windshield washer jar and pump assembly with the 3 bolts.
- Torque:
- 5.5 N*m{ 56 kgf*cm, 49 in.*lbf}
Install the upper part of the windshield washer jar and pump assembly to the windshield washer jar and pump assembly.
Install the bolt.
- Torque:
- 5.5 N*m{ 56 kgf*cm, 49 in.*lbf}
Connect the 2 connectors.
| 4. INSTALL WINDSHIELD WASHER JAR AND PUMP ASSEMBLY (w/ Headlight Cleaner System) |
Install the windshield washer jar and pump assembly with the 3 bolts.
- Torque:
- 5.5 N*m{ 56 kgf*cm, 49 in.*lbf}
Install the upper part of the windshield washer jar and pump assembly to the windshield washer jar and pump assembly.
Install the bolt.
- Torque:
- 5.5 N*m{ 56 kgf*cm, 49 in.*lbf}
Connect the headlight cleaner hose to the windshield washer jar and pump assembly.
Connect the 4 connectors.
| 5. FILL UP WINDSHIELD WASHER JAR AND PUMP ASSEMBLY WITH WASHER FLUID |
Connect the washer hose to the windshield washer motor and pump assembly and fill the washer jar with washer fluid.
| 6. INSTALL NO. 3 COOL AIR INTAKE DUCT SUB-ASSEMBLY |
Install the No. 3 cool air intake duct sub-assembly with the 2 bolts and the screw.
- Torque:
- 5.5 N*m{ 56 kgf*cm, 49 in.*lbf}
Engage the engine under cover clip.
Install the 3 front fender liner LH screws.
| 7. INSTALL HEADLIGHT ASSEMBLY LH |
Install the headlight assembly with the headlight bracket pin.
Install the 3 bolts.
Connect the connector.
| 8. INSTALL FRONT BUMPER ASSEMBLY |
| 9. INSTALL FRONT UPPER FENDER PROTECTOR LH |
Operate the wiper, and stop the windshield wiper motor at the automatic stop position.
Clean the wiper arm serrations.
Clean the wiper pivot serrations with a wire brush (when reinstalling).
Install the front wiper arm and blade assembly LH with the nut at the position as shown in the illustration.
- Torque:
- 22 N*m{ 224 kgf*cm, 16 ft.*lbf}
- HINT:
- Hold the arm hinge by hand to fasten the nut.
| Area | Measurement |
| A | 15 to 30 mm (0.59 to 1.18 in.) |
| B | Approx. 40 mm (1.57 in.) |
| 10. INSTALL ENGINE ROOM SIDE COVER LH (for 4GR-FSE) |
Install the side cover with the 5 clips.
| 11. INSTALL ENGINE ROOM SIDE COVER LH (for 2AD-FHV) |
Install the side cover with the 4 clips.
| 12. INSTALL COOL AIR INTAKE DUCT SEAL |
Install the intake duct seal with the 11 clips.