Transfer System Data List / Active Test

Drivetrain. Land Cruiser. Urj200, 202 Grj200 Vdj200
Jf2A Transfer 4Wd Awd. Land Cruiser. Urj200, 202 Grj200 Vdj200

  1. DATA LIST OF 4 WHEEL DRIVE CONTROL ECU

Transfer System -- Data List / Active Test


NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
HINT:
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

DATA LIST OF 4 WHEEL DRIVE CONTROL ECU

  1. Turn the ignition switch off.

  2. Connect the GTS to the DLC3.

  3. Turn the ignition switch to ON.

  4. Turn the GTS on.

  5. Enter the following menus: Powertrain / Four Wheel Drive / Data List.

  6. According to the display on the GTS, read the Data List.

    Four Wheel Drive
    Tester Display
    		Measurement Item/Range
    		Normal Condition
    		Diagnostic Note
    FR Wheel Speed
    		Front wheel speed sensor RH reading/
    Min.: 0.00 km/h (0.00 mph)
    Max.: 327.67 km/h (203.61 mph)
    		Vehicle stopped: 0.00 km/h (0.00 mph)
    		No large fluctuations when driving at a constant speed.
    FL Wheel Speed
    		Front wheel speed sensor LH reading/
    Min.: 0.00 km/h (0.00 mph)
    Max.: 327.67 km/h (203.61 mph)
    		Vehicle stopped: 0.00 km/h (0.00 mph)
    		No large fluctuations when driving at a constant speed.
    RR Wheel Speed
    		Rear wheel speed sensor RH reading/
    Min.: 0.00 km/h (0.00 mph)
    Max.: 327.67 km/h (203.61 mph)
    		Vehicle stopped: 0.00 km/h (0.00 mph)
    		No large fluctuations when driving at a constant speed.
    RL Wheel Speed
    		Rear wheel speed sensor LH reading/
    Min.: 0.00 km/h (0.00 mph)
    Max.: 327.67 km/h (203.61 mph)
    		Vehicle stopped: 0.00 km/h (0.00 mph)
    		No large fluctuations when driving at a constant speed.
    Vehicle Speed
    		Maximum wheel speed sensor reading/
    Min.: 0.00 km/h (0.00 mph)
    Max.: 327.67 km/h (203.61 mph)
    		Vehicle stopped: 0.00 km/h (0.00 mph)
    		No large fluctuations when driving at a constant speed.
    Transfer Oil Temperature
    		Transfer shift actuator temperature/
    Min.: -56°C (-69°F)
    Max.: 199°C (390°F)
    		Displays transfer shift actuator temperature
    		-
    Ambient Temperature
    		Ambient Temperature/
    Min.: -56°C (-69°F)
    Max.: 199°C (390°F)
    		Displays ambient temperature
    		-
    Transfer Position Control SW
    		Transfer position switch status/
    ON or OFF
    		ON: L4
    OFF: H4
    		-
    Center Differential Lock Control SW
    		Center differential lock switch status/
    ON or OFF
    		ON: Switch pressed and held
    OFF: Switch not pressed
    		-
    Rear Differential Lock Control SW
    		Differential lock switch status/
    ON or OFF
    		ON: RR (LOCK)
    OFF: OFF (FREE)
    		Used only for vehicles with a rear differential lock.
    Always displays OFF for vehicles without a rear differential lock.
    Center Differential Lock Position SW
    		Center differential lock detection switch status/
    ON or OFF
    		ON: Switch on (lock)
    OFF: Switch off (free)
    		-
    Transfer Neutral Position SW
    		Neutral position detection switch status/
    ON or OFF
    		ON: Switch on (neutral position)
    OFF: Switch off (not in neutral position)
    		Used for vehicles with a manual transmission.
    Always displays OFF for vehicles with an automatic transmission.
    Displays ON when the L4 switching conditions are not met. Displays OFF when the conditions are met.
    Rear Differential Lock Position SW
    		Rear differential lock position switch status/
    ON or OFF
    		ON: Switch on (lock)
    OFF: Switch off (free)
    		Used only for vehicles with a rear differential lock.
    Always displays OFF for vehicles without a rear differential lock.
    IG SW
    		Ignition switch status/
    ON or OFF
    		ON: Ignition switch ON
    		-
    Center Differential Lock Limit SW (TL2)
    		Center differential lock limit switch (TL2) status/
    ON or OFF
    		ON: Switching between free and lock, or set to lock
    OFF: Set to free
    		-
    Center Differential Lock Limit SW (TL3)
    		Center differential lock limit switch (TL3) status/
    ON or OFF
    		ON: Set to free or switching between free and lock
    OFF: Set to lock
    		-
    Rear Differential Lock Limit SW (RLY1)
    		Limit switch (RLY1) status/
    ON or OFF
    		ON: Set to free or switching between free and lock
    OFF: Set to lock
    		Used only for vehicles with a rear differential lock.
    Always displays OFF for vehicles without a rear differential lock.
    Rear Differential Lock Limit SW (RLY2)
    		Limit switch (RLY2) status/
    ON or OFF
    		ON: Switching between free and lock, or set to lock
    OFF: Set to free
    		Used only for vehicles with a rear differential lock.
    Always displays OFF for vehicles without a rear differential lock.
    H-L Limit SW (HL1)
    		High-low transfer limit switch (HL1) status/
    ON or OFF
    		ON: 4H
    OFF: 4L
    		Switches from on to off: While switching from 4H to 4L
    Switches from off to on: While switching from 4L to 4H
    H-L Limit SW (HL2)
    		High-low transfer limit switch (HL2) status/
    ON or OFF
    		ON: 4L
    OFF: 4H
    		Switches from off to on: While switching from 4H to 4L
    Switches from on to off: While switching from 4L to 4H
    H-L Limit SW (HL3)
    		High-low transfer limit switch (HL3) status/
    ON or OFF
    		ON: While switching between 4H and 4L
    OFF: Set to 4H or 4L
    		-
    Clutch SW
    		Clutch start switch status/
    ON or OFF
    		ON: Clutch pedal depressed
    OFF: Clutch pedal released
    		Used only for vehicles with a manual transmission.
    Displays OFF for vehicles with an automatic transmission.
    Shift SW Status (N Range)
    		Shift lever neutral condition/
    ON or OFF
    		ON: Shift lever in N*1 or shift lever in neutral*2
    OFF: Shift lever not in N*1 or shift lever not in neutral*2
    		-
    Engine Fail Signal
    		Engine control system malfunction status/
    Normal or Abnormal
    		Normal: Engine control system normal
    		Abnormal: Engine control system malfunctioning
    Shift SW Status (P Range)
    		Shift lever P condition/
    ON or OFF
    		ON: Shift lever in P
    OFF: Shift lever not in P
    		Used only for vehicles with an automatic transmission.
    Displays OFF for vehicles with a manual transmission.
    Stop Light SW
    		Stop light switch assembly condition/
    ON or OFF
    		ON: Brake pedal depressed
    OFF: Brake pedal released
    		-
    VSC System
    		VSC system availability/
    Without or With
    		Without: w/o VSC
    With: w/ VSC
    		-
    VSC Fail Signal
    		VSC system malfunction status/
    Normal or Abnormal
    		Normal: VSC system normal
    		Abnormal: VSC system malfunctioning or vehicle without VSC
    Center Differential Lock Shift Motor Target Current
    		Center differential lock shift motor driver circuit target current value/
    Min.: 0.0 A
    Max.: 25.5 A
    		Normal: 0.0 A
    Switching: 0.0 to 25.5 A
    		-
    H-L Shift Motor Target Current
    		High-low transfer shift motor drive circuit target current value/
    Min.: 0.0 A
    Max.: 25.5 A
    		Normal: 0.0 A
    Switching: 0.0 to 25.5 A
    		-
    Rear Differential Lock Shift Motor Target Current
    		Rear differential lock shift motor drive circuit target current value/
    Min.: 0.0 A
    Max.: 25.5 A
    		Normal: 0.0 A
    Switching: 0.0 to 25.5 A
    		Used only for vehicles with a rear differential lock.
    Always displays 0 A for vehicles without a rear differential lock.
    Motor Actual Current
    		Motor drive circuit actual current value/
    Min.: 0.0 A
    Max.: 25.5 A
    		Normal: 0.0 A
    Switching: 0.0 to 25.5 A
    		-
    Motor Energization Status Signal
    		Motor power signal status/
    ON or OFF
    		ON: Power supplied to motor
    OFF: Power not supplied to motor
    		-
    C/C Cancel Request
    		Cruise control cancellation signal status/
    ON or OFF
    		ON: Cruise control cancellation requested
    OFF: Cruise control cancellation not requested
    		-
    L4 Position Signal
    		L4 status signal/
    ON or OFF
    		ON: L4 state
    OFF: State other than L4
    		-
    Rear Differential Lock Position Signal
    		Rear differential lock condition signal/
    ON or OFF
    		ON: Lock condition
    OFF: Condition other than lock
    		Used only for vehicles with a rear differential lock.
    Always displays OFF for vehicles without a rear differential lock.
    H-L Actuator Fail Signal
    		High-low transfer actuator malfunction status/
    Normal or Abnormal
    		Normal: High-low transfer actuator normal
    		Abnormal: High-low transfer actuator malfunctioning
    Center Differential Lock Position Signal
    		Center differential lock condition signal/
    ON or OFF
    		ON: Lock condition
    OFF: Condition other than lock
    		-
    Transfer Neutral Position Signal
    		Transfer neutral condition signal/
    ON or OFF
    		ON: Neutral position condition
    OFF: Condition other than neutral position
    		Used only for vehicles with a manual transmission.
    Displays OFF for vehicles with an automatic transmission.
    Displays ON when the L4 switching conditions are not met. Displays OFF when the conditions are met.
    Buzzer Request
    		Buzzer sounding request/
    Sound, Sound(3 times), No Sound
    		No Sound: Does not sound
    		Sound(3 times): During a malfunction*3
    L4 Indicator Request
    		4LO indicator light request/
    Blink3, Blink1, ON, OFF
    1. Blink3: Indicator light rapidly blinks
    2. Blink1: Indicator light blinks
    3. ON: Indicator light illuminates
    4. OFF: Indicator light turns off
    1. Blinking: 0.5 second intervals (0.5 seconds on and 0.5 seconds off)
    2. Rapidly blinking: 0.25 second intervals (0.25 seconds on and 0.25 seconds off)
    Rear Differential Lock Indicator Request
    		Rear differential lock indicator light request/
    Blink3, Blink2, Blink1, ON or OFF
    1. Blink3: Indicator light blinks
    2. Blink2: Indicator light blinks 3 times
    3. Blink1: Indicator light blinks
    4. ON: Indicator light illuminates
    5. OFF: Indicator light turns off
    1. Blinking: 0.5 second intervals (0.5 seconds on and 0.5 seconds off)
    2. Rapidly blinking: 0.25 second intervals (0.25 seconds on and 0.25 seconds off)
    Used only for vehicles with a rear differential lock.
    Always displays OFF for vehicles without a rear differential lock.
    Center Differential Lock Indicator Request
    		Center differential lock indicator light request/
    Blink3, Blink2, Blink1, ON or OFF
    1. Blink3: Indicator light rapidly blinks
    2. Blink2: Indicator light blinks 3 times
    3. Blink1: Indicator light blinks
    4. ON: Indicator light illuminates
    5. OFF: Indicator light turns off
    1. Blinking: 0.5 second intervals (0.5 seconds on and 0.5 seconds off)
    2. Rapidly blinking: 0.25 second intervals (0.25 seconds on and 0.25 seconds off)
    IG Voltage
    		IG monitor voltage/
    Min.: 0.0 V
    Max.: 25.5 V
    		11 to 14 V: Ignition switch ON
    		-
    Motor Voltage
    		Motor driver circuit monitor voltage/
    Min.: 0.0 V
    Max.: 25.5 V
    		Normal: 1.5 to 12.0 V
    Switching: 3.5 V
    		-
    Mode Status
    		Mode transition condition/
    Initial Control, Particular Control at Start-Up, Shift Setting Control at Start-Up, H4F, H4L, L4F, L4L, L4LL*4, H4F->H4L, H4L->H4F, L4F->L4L, L4L->L4F, H4F->L4F, L4F->H4F, H4L->L4L, L4L->H4L, L4L->L4LL*4, L4LL->L4L*4, S04, S05, S06, S07, S08, S09, S10, B1, B2, B3, B4, HF1
    		Transition condition of the high-low transfer actuator, center differential lock actuator and differential lock shift actuator*6
    HINT:
    1. S04 to S10: Control while switching limited
    2. B1 to B4: During return control
    3. HF1: During fuel control
    Motor Relay (RY1-1)
    		Internal ECU relay (RY1-1) condition*5/
    ON or OFF
    		ON: Relay on
    OFF: Relay off
    		-
    Motor Relay (RY1-2)
    		Internal ECU relay (RY1-2) condition*5/
    ON or OFF
    		ON: Relay on
    OFF: Relay off
    		-
    Motor Relay (RY2-1)
    		Internal ECU relay (RY2-1) condition*5/
    ON or OFF
    		ON: Relay on
    OFF: Relay off
    		-
    Motor Relay (RY2-2)
    		Internal ECU relay (RY2-2) condition*5/
    ON or OFF
    		ON: Relay on
    OFF: Relay off
    		-
    AT/MT
    		AT or MT identification/
    AT or MT
    		AT: Automatic transmission
    MT: Manual transmission
    		-
    CAN Signal Invalid Status by IG Voltage Low
    		Whether CAN communication data invalid condition due to IG voltage drop/
    Valid or Inval
    		Valid: IG voltage 10 V or higher
    		Inval: IG voltage below 10 V
    SW Input Invalid Status by IG Voltage Low
    		Input invalid condition of switches inside actuator due to IG voltage drop/
    Valid or Inval
    		Valid: IG voltage 7.4 V or higher
    		Inval: IG voltage below 7.4 V
    Transfer Shift Invalid Status by IG Voltage Low
    		Transfer shift actuator switching operation invalid condition due to IG voltage drop/
    Valid or Inval
    		Valid: IG voltage 10 V or higher
    		Inval: IG voltage below 10 V
    Number of DTC
    		Number of DTCs stored/
    Min.: 0
    Max.: 255
    		0
    		-

    1. *1: for Automatic Transmission
    2. *2: for Manual Transmission
    3. *3: For details regarding malfunctions, refer to the buzzer sounding conditions of the diagnosis system (Click here).
    4. *4: Item not equipped, therefore not displayed
    5. *5: For the position of the relay, refer to the P17A9 wiring diagram (Click here).
    6. *6: w/ Rear Differential Lock