Dtc P08Ce Shift Solenoid J Stuck On

Drivetrain. Land Cruiser. Urj200, 202 Grj200 Vdj200
Ae80F Automatic Transmission Transaxle. Land Cruiser. Urj200, 202 Grj200 Vdj200

DESCRIPTION

MONITOR DESCRIPTION

INSPECTION PROCEDURE

CHECK DTC OUTPUT (IN ADDITION TO DTC P08CE)

CLEAR DTC AND PERFORM STALL SPEED TEST

INSPECT SHIFT SOLENOID VALVE SC2

INSPECT SHIFT SOLENOID VALVE SL3

INSPECT SHIFT SOLENOID VALVE SLT

INSPECT TRANSMISSION VALVE BODY ASSEMBLY

DTC P08CE Shift Solenoid "J" Stuck On


DESCRIPTION

Based on signals from the transmission revolution sensors (NT and SP2), the actual gear is detected.
If the detected gear is different than the commanded gear, the TCM detects related mechanical problems in the shift solenoid valves, transmission valve body assembly and automatic transmission assembly (clutch, brake, gear, etc.).

HINT:
Actual gear when a malfunction occurs in shift solenoid valve SC2 (without fail-safe control):

TCM commanded gear
1st
2nd
3rd
4th
5th
6th
7th
8th
Actual gear during SC2 stuck ON malfunction*
1st
2nd
3rd
4th
5th
6th
7th
8th
  1. *: Vehicle does not move with shift lever in R

DTC No.
DTC Detection Condition
  1. Diagnosis Condition
  2. Malfunction Status
  3. Malfunction Time
  4. Other
Trouble Area
P08CE
  1. Battery voltage is 9.5 V or higher, engine speed is more than 400 rpm, and the vehicle is driven with the shift lever in R (no malfunctions are detected in shift solenoid valve SC1, SC2, SL1, SL2, SL3, SL4, SL5, SLT, SLU, park/neutral position switch assembly, TCM, electronic throttle, knock control sensor, No. 1 ATF temperature sensor, transmission revolution sensors (NT), and CAN communication system)
  2. The engine overruns (neutral status).
  3. Malfunction status is detected 3 times per trip
  4. 2-trip detection logic
  1. Shift solenoid valve SC2
  2. Shift solenoid valve SL3
  3. Shift solenoid valve SLT
  4. Transmission valve body assembly
  5. Automatic transmission assembly (clutch, brake, gear, etc)

MONITOR DESCRIPTION

This DTC indicates a "stuck ON" malfunction of shift solenoid valve SC2.
When the vehicle does not move with the shift lever in R, the TCM stores the DTC.

INSPECTION PROCEDURE

NOTICE:
Perform registration and/or initialization when parts related to the automatic transmission are replaced (Click here).
HINT:
After performing repair, clear the DTCs and perform the following procedure to check that DTCs are not output.
  1. Start the engine.*1
  2. Drive the vehicle backward with the shift lever in R.*2
  3. Turn the engine switch off.
  4. Perform steps (*1) through (*2) again.
  5. Check for DTCs again (Click here).
1.CHECK DTC OUTPUT (IN ADDITION TO DTC P08CE)

  1. Connect the GTS to the DLC3.

  1. Turn the engine switch on (IG).

  1. Turn the GTS on.

  1. Enter the following menus: Powertrain / ECT / Trouble Codes.

  1. Read the DTCs using the GTS.

    Result
    Result
    		Proceed to
    DTC P08CE and DTC P0746, P076B, P076C, P0776, P0796, P08CD, P2714, P2808 and/or P2817 are output
    		A
    Only DTC P08CE is output
    		B
    DTCs other than P0746, P076B, P076C, P0776, P0796, P08CD, P08CE, P2714, P2808 and P2817 are also output
    		C
    HINT:
    If DTCs other than P0746, P076B, P076C, P0776, P0796, P08CD, P08CE, P2714, P2808 and P2817 are output, perform troubleshooting for those DTCs first.


B
Go to step 3

C
GO TO DTC CHART (Click here)
A


2.CLEAR DTC AND PERFORM STALL SPEED TEST

  1. Clear the DTCs (Click here).

    HINT:
    Write down the currently output DTCs before clearing them.

  1. Perform the stall speed test (Click here).

    Result
    Test Condition
    		Proceed to
    Stall speed test can be performed
    		A
    Stall speed test cannot be performed
    		B


B
Go to step 5
A


3.INSPECT SHIFT SOLENOID VALVE SC2


    Land Cruiser. Urj200, 202 Grj200 Vdj200.Ae80F Automatic Transmission Transaxle.Automatic Transmission System. Dtc P08Ce Shift Solenoid J Stuck On

  1. Remove the shift solenoid valve SC2 (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    		Condition
    		Specified Condition
    Terminal of shift solenoid valve SC2 connector - Shift solenoid valve SC2 body
    		20°C (68°F)
    		11 to 15 Ω

  1. Apply 12 V battery voltage to the shift solenoid valve and check that the valve moves and makes an operating noise.

    OK:
    Measurement Condition
    		Specified Condition
    1. Battery positive (+) → Shift solenoid valve SC2 connector
    2. Battery negative (-) → Shift solenoid valve SC2 body
    		Valve moves and makes an operating noise
Text in Illustration
*1
Shift Solenoid Valve SC2


NG
REPLACE SHIFT SOLENOID VALVE SC2 (Click here)
OK


4.INSPECT SHIFT SOLENOID VALVE SL3


    Land Cruiser. Urj200, 202 Grj200 Vdj200.Ae80F Automatic Transmission Transaxle.Automatic Transmission System. Dtc P08Ce Shift Solenoid J Stuck On

  1. Remove the shift solenoid valve SL3 (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    		Condition
    		Specified Condition
    Terminal 1 of the shift solenoid valve SL3 - Terminal 2
    		20°C (68°F)
    		5.0 to 5.6 Ω

  1. Apply 12 V battery voltage to the shift solenoid valve and check that the valve moves and makes an operating noise.

    OK:
    Measurement Condition
    		Specified Condition
    1. Battery positive (+) with a 21 W bulb → Terminal 2
    2. Battery negative (-) → Terminal 1
    		Valve moves and makes an operating noise
Text in Illustration
*1
Shift Solenoid Valve SL3


NG
REPLACE SHIFT SOLENOID VALVE SL3 (Click here)
OK


5.INSPECT SHIFT SOLENOID VALVE SLT


    Land Cruiser. Urj200, 202 Grj200 Vdj200.Ae80F Automatic Transmission Transaxle.Automatic Transmission System. Dtc P08Ce Shift Solenoid J Stuck On

  1. Remove the shift solenoid valve SLT (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    		Condition
    		Specified Condition
    Terminal 1 of the shift solenoid valve SLT - Terminal 2
    		20°C (68°F)
    		5.0 to 5.6 Ω

  1. Apply 12 V battery voltage to the shift solenoid valve and check that the valve moves and makes an operating noise.

    OK:
    Measurement Condition
    		Specified Condition
    1. Battery positive (+) with a 21 W bulb → Terminal 2
    2. Battery negative (-) → Terminal 1
    		Valve moves and makes an operating noise
Text in Illustration
*1
Shift Solenoid Valve SLT


NG
REPLACE SHIFT SOLENOID VALVE SLT (Click here)
OK


6.INSPECT TRANSMISSION VALVE BODY ASSEMBLY

  1. Check the transmission valve body assembly (Click here).

    OK:
    There is no foreign matter on each valve and they operate smoothly.


NG
REPAIR OR REPLACE TRANSMISSION VALVE BODY ASSEMBLY (Click here)
OK

REPAIR OR REPLACE AUTOMATIC TRANSMISSION ASSEMBLY (Click here)