Can Communication System (For Rhd With Central Gateway Ecu) Combination Meter Ecu Communication Stop Mode

Power Source Network. Land Cruiser. Urj200, 202 Grj200 Vdj200
Networking. Land Cruiser. Urj200, 202 Grj200 Vdj200

DESCRIPTION

WIRING DIAGRAM

INSPECTION PROCEDURE

CHECK FOR OPEN IN CAN BUS WIRE (COMBINATION METER ASSEMBLY CAN MAIN WIRE)

CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BATTERY AND BODY GROUND)

CAN COMMUNICATION SYSTEM (for RHD with Central Gateway ECU) - Combination Meter ECU Communication Stop Mode


DESCRIPTION


Detection Item
Symptom
Trouble Area
Combination Meter ECU Communication Stop Mode
Either Condition is met:
  1. "Combination Meter" is not displayed on the "Bus Check" screen (Click here).
  2. Communication system DTCs (DTCs that start with U) that are output correspond to "Combination Meter ECU Communication Stop Mode" in "DTC Combination Table" (Click here).
  1. Combination meter assembly CAN main wire or connector
  2. Power source circuit of combination meter assembly
  3. Combination meter assembly ground circuit
  4. Combination meter assembly

WIRING DIAGRAM


Land Cruiser. Urj200, 202 Grj200 Vdj200.Networking.Lin Communication System.Can Communication System (For Rhd With Central Gateway Ecu) Combination Meter Ecu Communication Stop Mode


INSPECTION PROCEDURE

NOTICE:
  1. Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output (Click here).
  2. Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.
  3. After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).
  4. Inspect the fuses for circuits related to this system before performing the following inspection procedure.
  5. After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.
  6. After the repair, perform CAN Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed (Click here).
HINT:
  1. Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.
  2. Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.
1.CHECK FOR OPEN IN CAN BUS WIRE (COMBINATION METER ASSEMBLY CAN MAIN WIRE)


    Land Cruiser. Urj200, 202 Grj200 Vdj200.Networking.Lin Communication System.Can Communication System (For Rhd With Central Gateway Ecu) Combination Meter Ecu Communication Stop Mode

  1. Disconnect the cable from the negative (-) battery terminal.

  1. Disconnect the combination meter assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    		Condition
    		Specified Condition
    E119-39 (CANH) - E119-40 (CANL)
    		Cable disconnected from negative (-) battery terminal
    		108 to 132 Ω
    Text in Illustration
    *a
    		Rear view of wire harness connector
    (to Combination Meter Assembly)


NG
REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO COMBINATION METER ASSEMBLY (CANH, CANL)
OK


2.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BATTERY AND BODY GROUND)


    Land Cruiser. Urj200, 202 Grj200 Vdj200.Networking.Lin Communication System.Can Communication System (For Rhd With Central Gateway Ecu) Combination Meter Ecu Communication Stop Mode

  1. Connect the cable to the negative (-) battery terminal.

    NOTICE:
    When connecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    		Condition
    		Specified Condition
    E119-21 (B) - Body ground
    		Always
    		11 to 14 V
    E119-22 (IG+) - Body ground
    		Ignition switch ON
    		11 to 14 V

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    		Condition
    		Specified Condition
    E119-20 (ET) - Body ground
    		Always
    		Below 1 Ω
Text in Illustration
*a
Rear view of wire harness connector
(to Combination Meter Assembly)


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE COMBINATION METER ASSEMBLY (Click here)