Ecd System (W/O Dpf) Brake Override System

Engine Hybrid System. Land Cruiser. Urj200, 202 Grj200 Vdj200
1Vd-Ftv Engine Control. Land Cruiser. Urj200, 202 Grj200 Vdj200

DESCRIPTION

INSPECTION PROCEDURE

CHECK DTC OUTPUT

READ VALUE USING INTELLIGENT TESTER (STOP LIGHT SWITCH)

INSPECT BRAKE PEDAL

READ VALUE USING INTELLIGENT TESTER (ACCELERATOR PEDAL POSITION SENSOR)

READ VALUE USING INTELLIGENT TESTER (VEHICLE SPEED)

READ VALUE USING INTELLIGENT TESTER (FR, FL, RR, RL WHEEL SPEED)

ECD SYSTEM (w/o DPF) - Brake Override System


DESCRIPTION

When the vehicle is being driven with the accelerator pedal depressed, depressing the brake pedal without releasing the accelerator pedal will activate the brake override system to restrict driving torque. The conditions for activating the brake override system as well as the items that are controlled are explained below.

Land Cruiser. Urj200, 202 Grj200 Vdj200.1Vd-Ftv Engine Control.Ecd System (W/ Dpf).Ecd System (W/O Dpf) Brake Override System

  1. Activation Conditions:
    1. Vehicle is running at or above the specified speed.
    2. The accelerator pedal is depressed beyond a specified level, and then the brake pedal is depressed.
    NOTICE:
    The vehicle may not enter the brake override system control due to the relation of the accelerator pedal angle and the vehicle's speed.
  1. Items Controlled:
    1. Driving torque is restricted.
    HINT:
    When this control is activated, the accelerator opening value is forcibly reduced to a fixed value. Therefore, the Accelerator Position value in the Data List is fixed regardless of the actual accelerator opening value (Accel Sens. No. 1 Volt %).
  1. Deactivation Conditions:
    1. When the Stop Light Switch turns OFF or the actual accelerator pedal angle increases or decreases beyond the specified range.

INSPECTION PROCEDURE

  1. Inspection Method
    Drive at 10 km/h (6.25 mph), depress the accelerator pedal by 1/2 to 3/4 and keep it in that position. Under these conditions, if the engine speed decreases to 1000 rpm when the brake pedal is depressed, then the brake override system has been activated.
CAUTION:
When carrying out the inspection, use a place where you are able to carry it out safely and also pay close attention to your surroundings.
Also, when driving, make absolutely sure that all road traffic laws, such as speed limits, are observed.
HINT:
  1. Under normal conditions, the Accelerator Position value changes in response to the Accel Sens. No. 1 Volt % value. For more information on the numerical values, refer to the Data List (Click here).
  2. If the Accelerator Position and Accel Sens. No. 1 Volt % values in the Data List diverge and the Accelerator Position value in the Data List is fixed even though Accel Sens. No. 1 Volt % is changing, check that this control is activated (use the GTS data saving function to record data while driving the vehicle and then confirm it after driving is completed).
NOTICE:
The brake override system restricts driving torque if the brake pedal is depressed when driving with the accelerator pedal depressed. If a customer reports experiencing loss of torque after the accelerator and brake pedals have both been intentionally depressed, explain to the customer that this is not a malfunction, and that the customer should avoid depressing both the accelerator and brake pedals at the same time.
Example: While operating the accelerator pedal, the customer uses their left foot to operate the brake pedal.
1.CHECK DTC OUTPUT

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester on.

  1. Enter the following menus: Utility / All Codes.

  1. Check DTCs.

    Result
    Result
    		Proceed to
    No DTC is output
    		A
    DTC is output
    		B


B
GO TO DTC CHART
A


2.READ VALUE USING INTELLIGENT TESTER (STOP LIGHT SWITCH)

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester on.

  1. Enter the following menus: Powertrain / Engine / Data List / Stop Light Switch.

  1. Check the Data List indication when the brake pedal is depressed and released.

    OK:

    Tester Display
    		Condition
    		Specified Condition
    Stop Light Switch
    		Brake pedal released
    		OFF
    Brake pedal depressed
    		ON


NG
INSPECT STOP LIGHT SWITCH ASSEMBLY (Click here)
OK


3.INSPECT BRAKE PEDAL

  1. Inspect and adjust the brake pedal (for LHD) (Click here).

  1. Inspect and adjust the brake pedal (for RHD) (Click here).

    HINT:
    If the stop light switch turns ON too late, the start of brake override system control may be delayed; if it turns ON too soon, brake override system control may begin too early, so conduct inspection of the brake pedal and stop light switch assembly.

Result:

Result
Proceed to
OK
A
NG (for LHD)
B
NG (for RHD)
C


B
REPAIR OR REPLACE BRAKE PEDAL (for LHD) (Click here)

C
REPAIR OR REPLACE BRAKE PEDAL (for RHD) (Click here)
A


4.READ VALUE USING INTELLIGENT TESTER (ACCELERATOR PEDAL POSITION SENSOR)

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester on.

  1. Enter the following menus: Powertrain / Engine / Data List / Accel Sens. No. 1 Volt % and Accel Sens. No. 2 Volt %.

  1. Read the value displayed on the tester.

    OK:

    Tester Display
    		Condition
    		Specified Condition
    Accel Sens. No. 1 Volt %
    		Accelerator Pedal
    Released → Depressed → Released
    		Values smoothly change following accelerator pedal operation
    Accel Sens. No. 2 Volt %
    HINT:
    For numerical values of Accel Sens. No. 1 Volt % and Accel Sens. No. 2 Volt %, refer to the Data List (Click here).


NG
REPLACE ACCELERATOR PEDAL SENSOR ASSEMBLY (Click here)
OK


5.READ VALUE USING INTELLIGENT TESTER (VEHICLE SPEED)

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester on.

  1. Start the engine.

  1. Enter the following menus: Powertrain / Engine / Data List / Vehicle Speed.

  1. Read the value displayed on the tester.

    Standard:

    Tester Display
    		Condition
    		Specified Condition
    Vehicle Speed
    		Vehicle stopped, engine running
    		0 km/h (0 mph)
    Vehicle running at constant speed between 16.1 to 64.4 km/h (10 to 40 mph)
    		No large fluctuations when driving at a constant speed
    CAUTION:
    When performing the confirmation driving pattern, obey all speed limits and traffic laws.
    HINT:
    Data can be captured relatively easily by using the snapshot function in the Data List. Confirm the data after performing the drive test.


NG
GO TO VEHICLE SPEED SENSOR "A" (Click here)
OK


6.READ VALUE USING INTELLIGENT TESTER (FR, FL, RR, RL WHEEL SPEED)

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester on.

  1. Start the engine.

  1. Enter the following menus: Chassis / ABS/VSC/TRC / Data List / FR Wheel Speed, FL Wheel Speed, RR Wheel Speed and RL Wheel Speed.

  1. Read the value displayed on the tester.

    Standard:

    Tester Display
    		Condition
    		Specified Condition
    FR Wheel Speed
    FL Wheel Speed
    RR Wheel Speed
    RL Wheel Speed
    		Vehicle stopped, engine running
    		0 km/h (0 mph)
    Vehicle running at constant speed between 16.1 to 64.4 km/h (10 to 40 mph)
    		No large fluctuations when driving at a constant speed
    CAUTION:
    When performing the confirmation driving pattern, obey all speed limits and traffic laws.
    HINT:
    Data can be captured relatively easily by using the snapshot function in the Data List. Confirm the data after performing the drive test.


NG
INSPECT FRONT OR REAR SPEED SENSOR
OK

END