Dtc B27A8 Open In Outside Luggage Compartment Electrical Key Antenna Circuit

Vehicle Interior. Land Cruiser. Urj200, 202 Grj200 Vdj200
Theft Deterrent Keyless Entry. Land Cruiser. Urj200, 202 Grj200 Vdj200

DESCRIPTION

WIRING DIAGRAM

INSPECTION PROCEDURE

CHECK CONNECTOR CONNECTION

CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU [SMART KEY ECU ASSEMBLY] - ELECTRICAL KEY ANTENNA [OUTSIDE LUGGAGE COMPARTMENT])

CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO ELECTRICAL KEY ANTENNA [OUTSIDE LUGGAGE COMPARTMENT])

REPLACE ELECTRICAL KEY ANTENNA (OUTSIDE LUGGAGE COMPARTMENT)

CLEAR DTC

CHECK FOR DTC

DTC B27A8 Open in Outside Luggage Compartment Electrical Key Antenna Circuit


DESCRIPTION

The certification ECU (smart key ECU assembly) generates a request signal and transmits the signal to the electrical key antenna (outside luggage compartment). For the electrical key antenna (outside luggage compartment) to detect when the electrical key transmitter sub-assembly is brought close to the vehicle, the received request signal is transmitted within approximately 1 m (3.28 ft.) of the back door. DTC B27A8 is stored by the certification ECU (smart key ECU assembly) when an open circuit is detected between the certification ECU (smart key ECU assembly) and electrical key antenna (outside luggage compartment) (between terminals CLG8 and ANTE8, or terminals CG8B and CLGB).

DTC Code
DTC Detection Condition
Trouble Area
DTC Output Confirmation Operation
B27A8
An open circuit is detected in the circuit between the certification ECU (smart key ECU assembly) and electrical key antenna (outside luggage compartment) (CLG8 - ANTE8, CG8B - CLGB) (1 trip detection logic*).
  1. Certification ECU (smart key ECU assembly)
  2. Electrical key antenna (outside luggage compartment)
  3. Harness or connector
Any time
  1. *: Only output while a malfunction is present and the engine switch is on (IG).

Vehicle Condition and Fail-safe Operation when Malfunction Detected
Vehicle Condition when Malfunction Detected
Fail-safe Operation when Malfunction Detected
Entry lock/unlock operation cannot be performed for back door
-

Related Data List and Active Test
DTC Code
Data List and Active Test
B27A8
Key diagnostic mode can be used to perform troubleshooting

WIRING DIAGRAM


Land Cruiser. Urj200, 202 Grj200 Vdj200.Theft Deterrent Keyless Entry.Entry And Start System (For Entry Function). Dtc B27A8 Open In Outside Luggage Compartment Electrical Key Antenna Circuit


INSPECTION PROCEDURE

NOTICE:
  1. The entry and start system (for Entry Function) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the entry and start system (for Entry Function) after confirming that the communication systems are functioning properly (Click here).
  2. When using the GTS with the engine switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.
  3. Before replacing the certification ECU (smart key ECU assembly), refer to entry and start system (for Entry Function) (Click here).
  4. After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".
1.CHECK CONNECTOR CONNECTION

  1. Check that the connectors are properly connected to the certification ECU (smart key ECU assembly) and electrical key antenna (outside luggage compartment).

    OK:
    Connectors are properly connected.


NG
CONNECT CONNECTORS PROPERLY
OK


2.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU [SMART KEY ECU ASSEMBLY] - ELECTRICAL KEY ANTENNA [OUTSIDE LUGGAGE COMPARTMENT])

  1. Disconnect the E129 and E130 certification ECU (smart key ECU assembly) connectors.

  1. Disconnect the K48 electrical key antenna (outside luggage compartment) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    		Condition
    		Specified Condition
    E129-2 (CLG8) - K48-2 (ANTE8)
    		Always
    		Below 1 Ω
    E129-1 (CG8B) - K48-1 (CLGB)
    		Always
    		Below 1 Ω
    E130-11 (E) - Body ground
    		Always
    		Below 1 Ω
    E129-2 (CLG8) or K48-2 (ANTE8) - Body ground
    		Always
    		10 kΩ or higher
    E129-1 (CG8B) or K48-1 (CLGB) - Body ground
    		Always
    		10 kΩ or higher

  1. Reconnect the E129 and E130 certification ECU (smart key ECU assembly) connectors.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO ELECTRICAL KEY ANTENNA [OUTSIDE LUGGAGE COMPARTMENT])

Land Cruiser. Urj200, 202 Grj200 Vdj200.Theft Deterrent Keyless Entry.Entry And Start System (For Entry Function). Dtc B27A8 Open In Outside Luggage Compartment Electrical Key Antenna Circuit


Text in Illustration
*a
Component with harness connected
(Certification ECU [Smart Key ECU Assembly])
*b
Waveform 1

  1. Using an oscilloscope, check the waveform.

    OK:

    Tester Connection
    		Switch Condition
    		Tool Setting
    		Specified Condition
    E129-2 (CLG8) - E130-11 (E)
    		Procedure:
    1. Engine switch off
    2. Electrical key transmitter sub-assembly brought outside vehicle
    3. All doors closed
    4. Back door opener switch assembly off → on
    		5 V/DIV., 500 ms/DIV.
    		Pulse generation (See waveform 1)
    E129-1 (CG8B) - E130-11 (E)
    		Procedure:
    1. Engine switch off
    2. Electrical key transmitter sub-assembly brought outside vehicle
    3. All doors closed
    4. Back door opener switch assembly off → on
    		5 V/DIV., 500 ms/DIV.
    		Pulse generation (See waveform 1)


NG
REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
OK


4.REPLACE ELECTRICAL KEY ANTENNA (OUTSIDE LUGGAGE COMPARTMENT)

  1. Temporarily replace the electrical key antenna (outside luggage compartment) with a new one (Click here).


NEXT


5.CLEAR DTC

  1. Clear the DTCs (Click here).


NEXT


6.CHECK FOR DTC

  1. Check for DTCs (Click here).

    OK:
    DTC B27A8 is not output.


NG
REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
OK

END (ELECTRICAL KEY ANTENNA [OUTSIDE LUGGAGE COMPARTMENT] WAS DEFECTIVE)