Vehicle Exterior. Land Cruiser. Urj200, 202 Grj200 Vdj200
Door Hatch. Land Cruiser. Urj200, 202 Grj200 Vdj200
Power Back Door System -- Data List / Active Test |
| DATA LIST |
- HINT:
- Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
- NOTICE:
- In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Body / (desired system) / Data List.
According to the display on the tester, read the Data List.
Back Door Tester Display Measurement Item/Range Normal Condition Diagnostic Note Door Lock Status Back door lock status signal / Lock or Unlock Lock: Back door locked
Unlock: Back door unlocked- Half Latch SW Half-latch switch signal / ON or OFF ON: Half-latch switch on
OFF: Half-latch switch off- Closer Position SW Closer position switch signal / ON or OFF ON: Closer position switch on
OFF: Closer position switch off- Pawl Position SW Pawl switch signal / ON or OFF ON: Back door lock motor open-latched
OFF: Back door lock motor except open-latched- Courtesy SW Back door courtesy switch signal / ON or OFF ON: Back door courtesy switch on
OFF: Back door courtesy switch off- RH CTSY SW of Tail Gate Panel Lower tail gate courtesy switch RH signal / ON or OFF ON: Tail gate closed
OFF: Tail gate open- LH CTSY SW of Tail Gate Panel Lower tail gate courtesy switch LH signal / ON or OFF ON: Tail gate closed
OFF: Tail gate open- PBD Touch Sensor (Right) Power back door sensor RH signal / ON, OFF or Open ON: Power back door sensor RH pressed
OFF: Power back door sensor RH not pressed
Open: Power back door sensor RH circuit open- PBD Touch Sensor (Left) Power back door sensor LH signal / ON, OFF or Open ON: Power back door sensor LH pressed
OFF: Power back door sensor LH not pressed
Open: Power back door sensor LH circuit open- PBD Main SW Power back door main switch signal / ON or OFF ON: Power back door main switch not pressed
OFF: Power back door main switch pressed- PBD Close SW Back door control switch signal / ON or OFF ON: Back door control switch on
OFF: Back door control switch off- IG SW Engine switch signal / ON or OFF ON: Engine switch on (IG)
OFF: Engine switch off- PBD Position (Close-1/4) Back door position (Full close - 1/4 open) / Caution or OK Caution: Back door position is not fully closed to 1/4 opened
OK: Back door position is fully closed to 1/4 opened- PBD Position (1/4-2/4) Back door position (1/4 open - 2/4 open) / Caution or OK Caution: Back door position is not 1/4 opened to 2/4 opened
OK: Back door position is 1/4 opened to 2/4 opened- PBD Position (2/4-3/4) Back door position (2/4 open - 3/4 open) / Caution or OK Caution: Back door position is not 2/4 opened to 3/4 opened
OK: Back door position is 2/4 opened to 3/4 opened- PBD Position (3/4-Open) Back door position (3/4 open - Full open) / Caution or OK Caution: Back door position is not 3/4 opened to fully opened
OK: Back door position is 3/4 opened to fully opened- PBD SW Operation Power back door switch operation condition signal / 0.0s or 0.8s Current customize setting displayed - PBD Buzz In Use Power back door warning buzzer operation condition signal / ON or OFF Current customize setting displayed - One Motion Function that opens the back door when the transmitter switch is pressed with the back door unlocked. / OFF, 1 Op, 2 Op, 0.8s or Not Use Current customize setting displayed - One Motion with Unlock Door Function that opens the back door when the transmitter switch is pressed (power back door one motion function). / OFF, Not Use, 2 Op or 0.8s Current customize setting displayed - Wireless PBD SW Operation Transmitter switch operation condition signal / 1 time, 2 times, 0.8 sPR, OFF Current customize setting displayed - # Codes Number of stored trouble codes / min.: 0, max.: 255 Number of DTCs will be displayed - Main Body Tester Display Measurement Item/Range Normal Condition Diagnostic Note Back Door Open SW Back door control switch signal / ON or OFF ON: Back door control switch on
OFF: Back door control switch off- Back Door Open Handle SW Back door opener handle switch signal / ON or OFF ON: Back door opener switch pushed
OFF: Back door opener switch not pushed- Entry & Start Tester Display Measurement Item/Range Normal Condition Diagnostic Note Tr/B-Door Lock SW Back door lock switch / ON or OFF ON: Back door lock switch pushed
OFF: Back door lock switch not pushed- Body No. 4 Tester Display Measurement Item/Range Normal Condition Diagnostic Note Courtesy Switch RH Lower tail gate courtesy switch RH signal / ON or OFF ON: Lower tail gate open
OFF: Lower tail gate closed- Courtesy Switch LH Lower tail gate courtesy switch LH signal / ON or OFF ON: Lower tail gate open
OFF: Lower tail gate closed-
| ACTIVE TEST |
- HINT:
- Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Body / Back Door / Active Test.
According to the display on the tester, perform the Active Test.
Back Door Tester Display Test Part Control Range Diagnostic Note Latch Releaser Operate back door lock ON / OFF - PBD Motor Operate power back door motor Forward / OFF
Reverse / OFF- PBD Clutch Operate power back door clutch ON / OFF - PBD Buzzer Operate warning buzzer ON / OFF - Courtesy SW Signal Operate back door courtesy light switch signal ON / OFF -