Power Back Door System Data List / Active Test

Vehicle Exterior. Land Cruiser. Urj200, 202 Grj200 Vdj200
Door Hatch. Land Cruiser. Urj200, 202 Grj200 Vdj200

  1. DATA LIST

  1. ACTIVE TEST

Power Back Door System -- Data List / Active Test



DATA LIST
HINT:
Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

  1. Connect the intelligent tester to the DLC3.

  2. Turn the engine switch on (IG).

  3. Turn the intelligent tester on.

  4. Enter the following menus: Body / (desired system) / Data List.

  5. According to the display on the tester, read the Data List.

    Back Door
    Tester Display
    		Measurement Item/Range
    		Normal Condition
    		Diagnostic Note
    Door Lock Status
    		Back door lock status signal / Lock or Unlock
    		Lock: Back door locked
    Unlock: Back door unlocked
    		-
    Half Latch SW
    		Half-latch switch signal / ON or OFF
    		ON: Half-latch switch on
    OFF: Half-latch switch off
    		-
    Closer Position SW
    		Closer position switch signal / ON or OFF
    		ON: Closer position switch on
    OFF: Closer position switch off
    		-
    Courtesy SW
    		Back door courtesy switch signal / ON or OFF
    		ON: Back door courtesy switch on
    OFF: Back door courtesy switch off
    		-
    RH CTSY SW of Tail Gate Panel
    		Lower tail gate courtesy switch RH signal / ON or OFF
    		ON: Tail gate closed
    OFF: Tail gate open
    		-
    LH CTSY SW of Tail Gate Panel
    		Lower tail gate courtesy switch LH signal / ON or OFF
    		ON: Tail gate closed
    OFF: Tail gate open
    		-
    PBD Touch Sensor (Right)
    		Power back door sensor RH signal / ON, OFF or Open
    		ON: Power back door sensor RH pressed
    OFF: Power back door sensor RH not pressed
    Open: Power back door sensor RH circuit open
    		-
    PBD Touch Sensor (Left)
    		Power back door sensor LH signal / ON, OFF or Open
    		ON: Power back door sensor LH pressed
    OFF: Power back door sensor LH not pressed
    Open: Power back door sensor LH circuit open
    		-
    PBD Main SW
    		Power back door main switch signal / ON or OFF
    		ON: Power back door main switch not pressed
    OFF: Power back door main switch pressed
    		-
    PBD Close SW
    		Back door control switch signal / ON or OFF
    		ON: Back door control switch on
    OFF: Back door control switch off
    		-
    IG SW
    		Engine switch signal / ON or OFF
    		ON: Engine switch on (IG)
    OFF: Engine switch off
    		-
    PBD Position (Close-1/4)
    		Back door position (Full close - 1/4 open) / Caution or OK
    		Caution: Back door position is not fully closed to 1/4 opened
    OK: Back door position is fully closed to 1/4 opened
    		-
    PBD Position (1/4-2/4)
    		Back door position (1/4 open - 2/4 open) / Caution or OK
    		Caution: Back door position is not 1/4 opened to 2/4 opened
    OK: Back door position is 1/4 opened to 2/4 opened
    		-
    PBD Position (2/4-3/4)
    		Back door position (2/4 open - 3/4 open) / Caution or OK
    		Caution: Back door position is not 2/4 opened to 3/4 opened
    OK: Back door position is 2/4 opened to 3/4 opened
    		-
    PBD Position (3/4-Open)
    		Back door position (3/4 open - Full open) / Caution or OK
    		Caution: Back door position is not 3/4 opened to fully opened
    OK: Back door position is 3/4 opened to fully opened
    		-
    PBD SW Operation
    		Power back door switch operation condition signal / 0.0s or 0.8s
    		Current customize setting displayed
    		-
    PBD Buzz In Use
    		Power back door warning buzzer operation condition signal / ON or OFF
    		Current customize setting displayed
    		-
    Wireless PBD SW Operation
    		Transmitter switch operation condition signal / 1 time, 2 times, 0.8 sPR, OFF
    		Current customize setting displayed
    		-
    # Codes
    		Number of stored trouble codes / min.: 0, max.: 255
    		Number of DTCs will be displayed
    		-

    Main Body
    Tester Display
    		Measurement Item/Range
    		Normal Condition
    		Diagnostic Note
    Back Door Open SW
    		Door control switch signal / ON or OFF
    		ON: Door control switch on
    OFF: Door control switch off
    		-


ACTIVE TEST
HINT:
Using the intelligent tester to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

  1. Connect the intelligent tester to the DLC3.

  2. Turn the engine switch on (IG).

  3. Turn the intelligent tester on.

  4. Enter the following menus: Body / Back Door / Active Test.

  5. According to the display on the tester, perform the Active Test.

    Back Door
    Tester Display
    		Test Part
    		Control Range
    		Diagnostic Note
    Latch Releaser
    		Operate back door lock
    		ON / OFF
    		-
    PBD Motor
    		Operate power back door motor
    		Forward / OFF
    Reverse / OFF
    		-
    PBD Clutch
    		Operate power back door clutch
    		ON / OFF
    		-
    PBD Buzzer
    		Operate warning buzzer
    		ON / OFF
    		-
    Courtesy SW Signal
    		Operate back door courtesy light switch signal
    		ON / OFF
    		-
    PBD Close SW Light
    		Operate PBD close switch Light
    		ON / OFF
    		-