Back Door Inspection

Vehicle Exterior. Land Cruiser. Urj200, 202 Grj200 Vdj200

Door Hatch. Land Cruiser. Urj200, 202 Grj200 Vdj200

INSPECT BACK DOOR REMOTE CONTROL ASSEMBLY
INSPECT LOWER TAIL GATE LOCK ASSEMBLY LH
INSPECT LOWER TAIL GATE LOCK ASSEMBLY RH

Back Door -- Inspection

1. INSPECT BACK DOOR REMOTE CONTROL ASSEMBLY

Land Cruiser. Urj200, 202 Grj200 Vdj200.Door Hatch.Tail Gate Closer System.Back Door Inspection

Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
1 - 2
Back door remote control is pulled (on)
Below 1 Ω
1 - 2
Back door remote control is not pulled (off)
10 kΩ or higher
If the result is not as specified, replace the back door remote control assembly.
Text in Illustration
*a
Component without harness connected
(Back Door Remote Control Assembly)
*b
Not pulled (off)
*c
Pulled (on)

2. INSPECT LOWER TAIL GATE LOCK ASSEMBLY LH

Land Cruiser. Urj200, 202 Grj200 Vdj200.Door Hatch.Tail Gate Closer System.Back Door Inspection

Operation check:
1. Set the lower tail gate lock LH to the full-latch position.
2. Apply battery voltage and check operation of the lower tail gate lock motor LH.
  OK:
  Measurement Condition
  Specified Condition
  Battery positive (+) → Terminal 6 (ACT-)
  Battery negative (-) → Terminal 5 (ACT+)
  Latch turns to open-latch position
  If the result is not as specified, replace the lower tail gate lock assembly LH.
3. Set the lower tail gate lock LH to the half-latch position.
4. Apply battery voltage and check operation of the lower tail gate lock motor LH.
  OK:
  Measurement Condition
  Specified Condition
  Battery positive (+) → Terminal 5 (ACT+)
  Battery negative (-) → Terminal 6 (ACT-)
  Latch turns to over-latch position
  If the result is not as specified, replace the lower tail gate lock assembly LH.
  Text in Illustration
  *a
  Component without harness connected
  (Lower Tail Gate Lock Assembly LH)
  *b
  Over-latch
  *c
  Full-latch
  *d
  Half-latch
  *e
  Open-latch

Land Cruiser. Urj200, 202 Grj200 Vdj200.Door Hatch.Tail Gate Closer System.Back Door Inspection

Resistance check:

Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Close Position Switch
Tester Connection	Condition	Specified Condition
7 (HND) - 8 (GND)	Over-latch	Below 1 Ω
7 (HND) - 8 (GND)	Full-latch	10 kΩ or higher
7 (HND) - 8 (GND)	Half-latch	10 kΩ or higher
7 (HND) - 8 (GND)	Open-latch	10 kΩ or higher

If the result is not as specified, replace the lower tail gate lock assembly LH.

Lower Tail Gate Courtesy Switch:

Tester Connection	Condition	Specified Condition
2 (FUL) - 3 (E1)	Over-latch	10 kΩ or higher
2 (FUL) - 3 (E1)	Full-latch	10 kΩ or higher
2 (FUL) - 3 (E1)	Half-latch	Below 1 Ω
2 (FUL) - 3 (E1)	Open-latch	Below 1 Ω

If the result is not as specified, replace the lower tail gate lock assembly LH.

Half-latch Switch:

Tester Connection	Condition	Specified Condition
1 (HAF) - 3 (E1)	Over-latch	10 kΩ or higher
1 (HAF) - 3 (E1)	Full-latch	Below 1 Ω
1 (HAF) - 3 (E1)	Half-latch	10 kΩ or higher
1 (HAF) - 3 (E1)	Open-latch	Below 1 Ω

If the result is not as specified, replace the lower tail gate lock assembly LH.

Pawl Switch:

Tester Connection	Condition	Specified Condition
4 (POL) - 3 (E1)	Over-latch	10 kΩ or higher
4 (POL) - 3 (E1)	Full-latch	Below 1 Ω
4 (POL) - 3 (E1)	Half-latch	Below 1 Ω
4 (POL) - 3 (E1)	Open-latch	10 kΩ or higher

If the result is not as specified, replace the lower tail gate lock assembly LH.

Text in Illustration
*a	Component without harness connected (Lower Tail Gate Lock Assembly LH)
*b	Over-latch
*c	Full-latch
*d	Half-latch
*e	Open-latch

3. INSPECT LOWER TAIL GATE LOCK ASSEMBLY RH

Land Cruiser. Urj200, 202 Grj200 Vdj200.Door Hatch.Tail Gate Closer System.Back Door Inspection

Operation check:
1. Set the lower tail gate lock RH to the full-latch position.
2. Apply battery voltage and check operation of the lower tail gate lock motor RH.
  OK:
  Measurement Condition
  Specified Condition
  Battery positive (+) → Terminal 6 (ACT-)
  Battery negative (-) → Terminal 5 (ACT+)
  Latch turns to open-latch position
  If the result is not as specified, replace the lower tail gate lock assembly RH.
3. Set the lower tail gate lock RH to the half-latch position.
4. Apply battery voltage and check operation of the lower tail gate lock motor RH.
  OK:
  Measurement Condition
  Specified Condition
  Battery positive (+) → Terminal 5 (ACT+)
  Battery negative (-) → Terminal 6 (ACT-)
  Latch turns to over-latch position
  If the result is not as specified, replace the lower tail gate lock assembly RH.
  Text in Illustration
  *a
  Component without harness connected
  (Lower Tail Gate Lock Assembly RH)
  *b
  Over-latch
  *c
  Full-latch
  *d
  Half-latch
  *e
  Open-latch

Land Cruiser. Urj200, 202 Grj200 Vdj200.Door Hatch.Tail Gate Closer System.Back Door Inspection

Resistance check:

Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Close Position Switch
Tester Connection	Condition	Specified Condition
7 (HND) - 8 (GND)	Over-latch	Below 1 Ω
7 (HND) - 8 (GND)	Full-latch	10 kΩ or higher
7 (HND) - 8 (GND)	Half-latch	10 kΩ or higher
7 (HND) - 8 (GND)	Open-latch	10 kΩ or higher

If the result is not as specified, replace the lower tail gate lock assembly RH.

Lower Tail Gate Courtesy Switch:

Tester Connection	Condition	Specified Condition
2 (FUL) - 3 (E1)	Over-latch	10 kΩ or higher
2 (FUL) - 3 (E1)	Full-latch	10 kΩ or higher
2 (FUL) - 3 (E1)	Half-latch	Below 1 Ω
2 (FUL) - 3 (E1)	Open-latch	Below 1 Ω

If the result is not as specified, replace the lower tail gate lock assembly RH.

Half-latch Switch:

Tester Connection	Condition	Specified Condition
1 (HAF) - 3 (E1)	Over-latch	10 kΩ or higher
1 (HAF) - 3 (E1)	Full-latch	Below 1 Ω
1 (HAF) - 3 (E1)	Half-latch	10 kΩ or higher
1 (HAF) - 3 (E1)	Open-latch	Below 1 Ω

If the result is not as specified, replace the lower tail gate lock assembly RH.

Pawl Switch:

Tester Connection	Condition	Specified Condition
4 (POL) - 3 (E1)	Over-latch	10 kΩ or higher
4 (POL) - 3 (E1)	Full-latch	Below 1 Ω
4 (POL) - 3 (E1)	Half-latch	Below 1 Ω
4 (POL) - 3 (E1)	Open-latch	10 kΩ or higher

If the result is not as specified, replace the lower tail gate lock assembly RH.

Text in Illustration
*a	Component without harness connected (Lower Tail Gate Lock Assembly RH)
*b	Over-latch
*c	Full-latch
*d	Half-latch
*e	Open-latch