INSTALL LOWER INSTRUMENT PANEL (w/o Driver Side Knee Airbag)
INSTALL DRIVER SIDE KNEE AIRBAG ASSEMBLY (w/ Driver Side Knee Airbag)
INSTALL NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (w/ Floor Under Cover)
INSTALL LOWER CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY
Steering Control Ecu (For Lhd) -- Installation |
| 1. INSTALL STEERING CONTROL ECU |
 |
Install the steering control ECU to the junction block with the bolt and nut.
- Torque:
- 8.0 N*m{82 kgf*cm, 71 in.*lbf}
| 2. INSTALL STEERING CONTROL ECU WITH JUNCTION BLOCK |
 |
Front side:
Connect the 5 connectors.
Rear side:
Install the steering control ECU with junction block with the bolt and 2 nuts.
- Torque:
- 8.0 N*m{82 kgf*cm, 71 in.*lbf}
Attach the 2 clamps.
Connect the 7 connectors.
| 3. INSTALL LOWER INSTRUMENT PANEL (w/o Driver Side Knee Airbag) |
 |
Attach the 2 claws and connect the DLC3.
Install the lower instrument panel with the 5 bolts.
| 4. INSTALL DRIVER SIDE KNEE AIRBAG ASSEMBLY (w/ Driver Side Knee Airbag) |
Connect the connector.
- NOTICE:
- When handling the airbag connector, take care not to damage the airbag wire harness.
 |
Install the driver side knee airbag with the 5 bolts.
- Torque:
- 10 N*m{102 kgf*cm, 7 ft.*lbf}
| 5. INSTALL NO. 1 SWITCH HOLE BASE |
 |
Connect the connectors.
Attach the 4 claws to install the No. 1 switch hole base.
| 6. INSTALL LOWER NO. 1 INSTRUMENT PANEL FINISH PANEL |
Connect the connectors.
for Automatic Air Conditioning System:
Attach the 2 claws to install the room temperature sensor.
 |
Attach the 2 claws to connect the 2 control cables.
 |
w/ Driver Side Knee Airbag:
Attach the 16 claws to install the lower No. 1 instrument panel finish panel.
Install the 2 bolts.
w/o Driver Side Knee Airbag:
Attach the 9 claws to install the lower No. 1 instrument panel finish panel.
Install the 2 bolts.
Attach the 2 claws to close the hole cover.
 |
| 7. INSTALL COWL SIDE TRIM BOARD LH |
 |
Attach the 2 clips to install the cowl side trim board.
Install the cap nut.
| 8. INSTALL NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (w/ Floor Under Cover) |
 |
Connect the connectors.
Attach the 3 claws to install the No. 1 instrument panel under cover.
Install the 2 screws.
| 9. INSTALL FRONT DOOR SCUFF PLATE LH |
 |
Attach the 7 claws and 4 clips to install the scuff plate.
| 10. INSTALL NO. 2 INSTRUMENT CLUSTER FINISH PANEL GARNISH |
Attach the 2 claws to install the No. 2 instrument cluster finish panel garnish.
Text in Illustration *A w/ Entry and Start System *B w/o Entry and Start System
| 11. INSTALL NO. 1 INSTRUMENT CLUSTER FINISH PANEL GARNISH |
 |
Attach the 3 claws to install the No. 1 instrument cluster finish panel garnish.
| 12. INSTALL INSTRUMENT SIDE PANEL LH |
 |
Attach the 6 claws to install the instrument side panel.
| 13. INSTALL LOWER CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY |
 |
Connect the connectors.
Attach the 7 claws to install the lower center instrument cluster finish panel sub-assembly.
| 14. INSTALL LOWER INSTRUMENT PANEL PAD SUB-ASSEMBLY RH |
 |
Attach the 7 claws to install the lower instrument panel pad sub-assembly.
Install the clip and screw.
| 15. INSTALL NO. 1 INSTRUMENT PANEL FINISH PANEL CUSHION |
 |
Attach the 7 claws to install the No. 1 instrument panel finish panel cushion.
| 16. INSTALL LOWER INSTRUMENT PANEL PAD SUB-ASSEMBLY LH |
 |
Connect the connectors and attach the 2 clamps.
Attach the 8 claws to install the lower instrument panel pad sub-assembly.
Install the clip and screw.
| 17. INSTALL NO. 2 INSTRUMENT PANEL FINISH PANEL CUSHION |
 |
Attach the 7 claws to install the No. 2 instrument panel finish panel cushion.
| 18. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
- NOTICE:
- When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).
| 19. PERFORM VARIABLE GEAR RATIO STEERING SYSTEM CALIBRATION |