Dtc P0500 Vehicle Speed Sensor A

Drivetrain. Land Cruiser. Urj200, 202 Grj200 Vdj200
Ab60F Automatic Transmission Transaxle. Land Cruiser. Urj200, 202 Grj200 Vdj200

DESCRIPTION

MONITOR DESCRIPTION

WIRING DIAGRAM

INSPECTION PROCEDURE

CHECK OPERATION OF SPEEDOMETER

READ VALUE USING INTELLIGENT TESTER (VEHICLE SPD)

CHECK COMBINATION METER ASSEMBLY (+S VOLTAGE)

CHECK COMBINATION METER ASSEMBLY (SPD SIGNAL WAVEFORM)

CHECK HARNESS AND CONNECTOR (COMBINATION METER - ECM)

DTC P0500 Vehicle Speed Sensor "A"


DESCRIPTION

The speed sensor detects the wheel speed and sends the appropriate signals to the skid control ECU. The skid control ECU converts these wheel speed signals into a 4-pulse signal and outputs it to the ECM via the combination meter. The ECM determines the vehicle speed based on the frequency of these pulse signals.

Land Cruiser. Urj200, 202 Grj200 Vdj200.Ab60F Automatic Transmission Transaxle.Automatic Transmission System (For 1Ur-Fe). Dtc P0500 Vehicle Speed Sensor A


DTC Code
DTC Detection Condition
Trouble Area
P0500
While the vehicle is being driven, no vehicle speed sensor signal is transmitted to the ECM (2 trip detection logic).
  1. Open or short in speed signal circuit
  2. Wheel speed sensor
  3. Combination meter
  4. ECM
  5. Skid control ECU

MONITOR DESCRIPTION

The ECM assumes that the vehicle is being driven when the indicated vehicle speed is more than 9 km/h (5.6 mph). If there is no speed signal from the combination meter despite these conditions being met, the ECM interprets this as a malfunction in the speed signal circuit. The ECM then illuminates the MIL and stores the DTC.

WIRING DIAGRAM


Land Cruiser. Urj200, 202 Grj200 Vdj200.Ab60F Automatic Transmission Transaxle.Automatic Transmission System (For 1Ur-Fe). Dtc P0500 Vehicle Speed Sensor A


INSPECTION PROCEDURE

HINT:
Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.
1.CHECK OPERATION OF SPEEDOMETER

  1. Drive the vehicle and check whether the operation of the speedometer in the combination meter is normal.

    HINT:
    1. The vehicle speed sensor is operating normally if the speedometer reading is normal.
    2. If the speedometer does not operate, check it by following the procedure described in Speedometer Malfunction (Click here).


NG
GO TO METER / GAUGE SYSTEM PROBLEM SYMPTOMS TABLE (Click here)
OK


2.READ VALUE USING INTELLIGENT TESTER (VEHICLE SPD)

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Enter the following menus: Powertrain / ECT / Data List.

  1. Drive the vehicle.

  1. According to the display on the tester, read the Data List.

    ECT
    Tester Display
    		Measurement Item/Range
    		Normal Condition
    		Diagnostic Note
    Vehicle Speed
    		Vehicle speed/
    Min.: 0 km/h (0 mph)
    Max.: 255 km/h (158 mph)
    		Actual vehicle speed
    		The speed is indicated on the speedometer.
    OK:
    Vehicle speeds displayed on intelligent tester and speedometer display are equal.


NG
Go to step 3
OK

CHECK FOR INTERMITTENT PROBLEMS (Click here)

3.CHECK COMBINATION METER ASSEMBLY (+S VOLTAGE)
Land Cruiser. Urj200, 202 Grj200 Vdj200.Ab60F Automatic Transmission Transaxle.Automatic Transmission System (For 1Ur-Fe). Dtc P0500 Vehicle Speed Sensor A

  1. Disconnect the combination meter connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    		Switch Condition
    		Specified Condition
    E7-4 (+S) - Body ground
    		Ignition switch ON
    		4.5 to 5.5 V


NG
Go to step 5
OK


4.CHECK COMBINATION METER ASSEMBLY (SPD SIGNAL WAVEFORM)
Land Cruiser. Urj200, 202 Grj200 Vdj200.Ab60F Automatic Transmission Transaxle.Automatic Transmission System (For 1Ur-Fe). Dtc P0500 Vehicle Speed Sensor A

  1. Move the shift lever to N.

  1. Jack up the vehicle.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    		Condition
    		Specified Condition
    E7-4 (+S) - Body ground
    1. Ignition switch ON
    2. Wheel is turned slowly
    		Voltage generated intermittently
    HINT:
    The output voltage should fluctuate up and down, similarly to the diagram, when the wheel is turned slowly.
    Result
    Result
    		Proceed to
    OK
    		A
    NG (w/ Multi-information Display)
    		B
    NG (w/o Multi-information Display)
    		C


B
REPLACE COMBINATION METER ASSEMBLY (Click here)

C
REPLACE COMBINATION METER ASSEMBLY (Click here)
A


5.CHECK HARNESS AND CONNECTOR (COMBINATION METER - ECM)
Land Cruiser. Urj200, 202 Grj200 Vdj200.Ab60F Automatic Transmission Transaxle.Automatic Transmission System (For 1Ur-Fe). Dtc P0500 Vehicle Speed Sensor A

  1. Disconnect the combination meter connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for LHD
    Tester Connection
    		Condition
    		Specified Condition
    E7-4 (+S) - A38-8 (SPD)
    		Always
    		Below 1 Ω
    E7-4 (+S) or A38-8 (SPD) - Body ground
    		Always
    		10 kΩ or higher
    for RHD
    Tester Connection
    		Condition
    		Specified Condition
    E7-4 (+S) - A52-8 (SPD)
    		Always
    		Below 1 Ω
    E7-4 (+S) or A52-8 (SPD) - Body ground
    		Always
    		10 kΩ or higher


NG
REPAIR HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)