Cruise Control System Clutch Switch Circuit

Engine Hybrid System. Land Cruiser. Urj200, 202 Grj200 Vdj200
Cruise Control. Land Cruiser. Urj200, 202 Grj200 Vdj200

DESCRIPTION

WIRING DIAGRAM

INSPECTION PROCEDURE

INSPECT FUSE (LH-IG)

CHECK HARNESS AND CONNECTOR (ECM - BATTERY)

INSPECT CLUTCH SWITCH ASSEMBLY

CHECK HARNESS AND CONNECTOR (ECM - CLUTCH SWITCH ASSEMBLY)

CRUISE CONTROL SYSTEM - Clutch Switch Circuit


DESCRIPTION

When the clutch pedal is released, the ECM receives positive (+) battery voltage through the LH-IG fuse. While depressing the clutch pedal, the clutch switch sends a signal to terminal D*1 or CLSW*2 of the ECM. The ECM cancels cruise control when terminal D*1 or CLSW*2 receives the signal.
HINT:
  1. *1: for 1GR-FE
  2. *2: for 1VD-FTV

WIRING DIAGRAM


Land Cruiser. Urj200, 202 Grj200 Vdj200.Cruise Control.Cruise Control System.Cruise Control System Clutch Switch Circuit


Land Cruiser. Urj200, 202 Grj200 Vdj200.Cruise Control.Cruise Control System.Cruise Control System Clutch Switch Circuit


INSPECTION PROCEDURE

1.INSPECT FUSE (LH-IG)

  1. Remove the LH-IG fuse from the main body ECU.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    		Condition
    		Specified Condition
    LH-IG fuse
    		Always
    		Below 1 Ω


NG
REPLACE FUSE
OK


2.CHECK HARNESS AND CONNECTOR (ECM - BATTERY)


    Land Cruiser. Urj200, 202 Grj200 Vdj200.Cruise Control.Cruise Control System.Cruise Control System Clutch Switch Circuit

  1. Disconnect the C45*1, C46*2, A38*3 or A52*4 ECM connector.

    HINT:
    1. *1: for 1GR-FE LHD
    2. *2: for 1GR-FE RHD
    3. *3: for 1VD-FTV LHD
    4. *4: for 1VD-FTV RHD

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    for 1GR-FE LHD
    Tester Connection
    		Switch Condition
    		Specified Condition
    C45-27 (D) - Body ground
    		Ignition switch ON
    Clutch pedal depressed
    		Below 1 V
    Ignition switch ON
    Clutch pedal released
    		11 to 14 V
    for 1GR-FE RHD
    Tester Connection
    		Switch Condition
    		Specified Condition
    C46-27 (D) - Body ground
    		Ignition switch ON
    Clutch pedal depressed
    		Below 1 V
    Ignition switch ON
    Clutch pedal released
    		11 to 14 V
    for 1VD-FTV LHD
    Tester Connection
    		Switch Condition
    		Specified Condition
    A38-42 (CLSW) - Body ground
    		Ignition switch ON
    Clutch pedal depressed
    		Below 1 V
    Ignition switch ON
    Clutch pedal released
    		11 to 14 V
    for 1VD-FTV RHD
    Tester Connection
    		Switch Condition
    		Specified Condition
    A52-42 (CLSW) - Body ground
    		Ignition switch ON
    Clutch pedal depressed
    		Below 1 V
    Ignition switch ON
    Clutch pedal released
    		11 to 14 V


NG
Go to step 3
OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)

3.INSPECT CLUTCH SWITCH ASSEMBLY


    Land Cruiser. Urj200, 202 Grj200 Vdj200.Cruise Control.Cruise Control System.Cruise Control System Clutch Switch Circuit

  1. Turn the ignition switch off.

  1. Remove the clutch switch assembly (Click here for LHD, Click here for RHD).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    		Switch Condition
    		Specified Condition
    1 - 2
    		Pushed (On)
    		Below 1 Ω
    Not pushed (Off)
    		10 kΩ or higher
    Result
    Result
    		Proceed to
    OK
    		A
    NG (for LHD)
    		B
    NG (for RHD)
    		C

  1. Install the clutch switch assembly (Click here for LHD, Click here for RHD).



B
REPLACE CLUTCH SWITCH ASSEMBLY (Click here)

C
REPLACE CLUTCH SWITCH ASSEMBLY (Click here)
A


4.CHECK HARNESS AND CONNECTOR (ECM - CLUTCH SWITCH ASSEMBLY)


    Land Cruiser. Urj200, 202 Grj200 Vdj200.Cruise Control.Cruise Control System.Cruise Control System Clutch Switch Circuit

  1. Disconnect the C45*1, C46*2, A38*3 or A52*4 ECM connector.

    HINT:
    1. *1: for 1GR-FE LHD
    2. *2: for 1GR-FE RHD
    3. *3: for 1VD-FTV LHD
    4. *4: for 1VD-FTV RHD

  1. Disconnect the A50*1 or e2*2 clutch switch assembly connector.

    HINT:
    1. *1: for LHD
    2. *2: for RHD

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for 1GR-FE LHD
    Tester Connection
    		Condition
    		Specified Condition
    C45-27 (D) - A50-2
    		Always
    		Below 1 Ω
    C45-27 (D) - Body ground
    		Always
    		10 kΩ or higher
    for 1GR-FE RHD
    Tester Connection
    		Condition
    		Specified Condition
    C46-27 (D) - e2-2
    		Always
    		Below 1 Ω
    C46-27 (D) - Body ground
    		Always
    		10 kΩ or higher
    for 1VD-FTV LHD
    Tester Connection
    		Condition
    		Specified Condition
    A38-42 (CLSW) - A50-2
    		Always
    		Below 1 Ω
    A38-42 (CLSW) - Body ground
    		Always
    		10 kΩ or higher
    for 1VD-FTV RHD
    Tester Connection
    		Condition
    		Specified Condition
    A52-42 (CLSW) - e2-2
    		Always
    		Below 1 Ω
    A52-42 (CLSW) - Body ground
    		Always
    		10 kΩ or higher


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - CLUTCH SWITCH ASSEMBLY)
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - CLUTCH SWITCH ASSEMBLY)