Headlight Assembly (For Halogen Headlight) -- Reassembly |
- NOTICE:
- Handle components indoors as much as possible to prevent foreign matter from entering and adhering to headlight assembly components.
- Do not reuse parts which have reduced fastening ability due to thread damage.
- Do not touch the inner surface of the lens and metallic surfaces as much as possible, or they may become dirty.
- Do not allow metallic surfaces to become dirty, as such surfaces become damaged even if they are only lightly wiped with a soft cloth.
- When installing components, make sure that the wire harness is not pinched or pulled.
- Do not use solvent to clean components. Only clean them with a dry cloth.
- HINT:
- Use the same procedure for the RH and LH sides.
- The procedure listed below is for the LH side.
| 1. INSTALL HEADLIGHT LENS GASKET |
Clean the headlight lens gasket installation groove.
Text in Illustration 
Area to Clean
 |
Prepare 2 screwdrivers, fold a piece of peeling paper over the tip of each screwdriver and fix the pieces of peeling paper in place with tape.
- HINT:
- Use the peeling paper that is supplied with the headlight lens gasket.
Using scissors, cut the headlight lens gasket at a 90°.
 |
Starting from the position shown in the illustration, set the headlight lens gasket into the straight groove counterclockwise until it meets the corner groove.
Text in Illustration 
Starting Point - NOTICE:
- Lightly set the gasket in place without pulling.
 |
Set the headlight lens gasket into the corner groove and using 2 screwdrivers with their tips wrapped with peeling paper, push the gasket into the bottom of the groove.
Text in Illustration 
Corner Groove 
Headlight Lens Gasket Peeling Paper - NOTICE:
- Lightly set the gasket in place without pulling.
- If the headlight lens gasket is set while pulled, the gasket will be pushed up at the corner groove.
 |
Repeat the following order while working in a circle back to the starting point.
Set headlight lens gasket into straight groove.
Push into bottom of groove.
Set into corner groove.
Push into bottom of groove.
Using scissors, cut the headlight lens gasket at a 45°angle at the starting point so that the gasket overlaps itself 20 mm (0.7874 in.) and set the gasket in place.
Text in Illustration *a 20 mm (0.7874 in.) Corner Groove
 |
Check the installation condition of the headlight lens gasket.
- OK:
- Gasket not pushed up or protruding.
No gap where gasket overlaps.
- NOTICE:
- Check the corners carefully since the gasket can easily become pushed up in those areas.
| 2. INSTALL HEADLIGHT LENS LH |
- NOTICE:
- Perform work using clean rubber gloves.
- Do not touch the inner surface of the lens with bare hands.
- If dirty, lightly wipe with a soft cloth.
Clean the headlight lens gasket contact surface.
Set the headlight lens LH in place.
- NOTICE:
- Set the headlight lens LH in the middle of the headlight lens gasket as shown in the illustration.
Text in Illustration Headlight Lens Gasket 
Head Light Housing Headlight Lens LH
 |
Check that the entire circumference of the headlight lens LH is positioned above the middle of the headlight lens gasket.
Attach the claws in the following order to install the headlight lens LH: The 2 claws D, 2 claws C, claw B, and then 2 claws A.
Text in Illustration *a Claw A *b Claw B *c Claw C *d Claw D
Install the 7 screws.
Text in Illustration *A Headlight Assembly LH Backside *B Headlight Assembly LH Surface
Install the outer bracket with the 2 screws.
Install the inner bracket with the 2 screws.
| 3. INSTALL FRONT BUMPER BAR REINFORCEMENT LH |
Attach the 2 guides to install the front bumper bar reinforcement LH.
Install the 2 screws.
| 4. INSTALL HEADLIGHT CORD |
Attach the wire harness clamp to install the headlight cord.
Attach the 2 claws to connect the 2 connectors.
| 5. INSTALL NO. 2 HEADLIGHT BULB |
Insert and turn the No. 2 headlight bulb clockwise until the bulb stops to install it.
- NOTICE:
- Do not touch the glass part of the No. 2 headlight bulb.
 |
| 6. INSTALL NO. 1 HEADLIGHT BULB |
Insert and turn the No. 1 headlight bulb clockwise until the bulb stops to install it.
- NOTICE:
- Do not touch the glass part of the No. 1 headlight bulb.
 |
| 7. INSTALL CLEARANCE LIGHT BULB |
Install the clearance light bulb to the bulb socket.
Align the matchmark of the bulb socket with the unlock position mark, and then rotate the bulb socket clockwise until the lock position mark to connect the bulb socket.
Text in Illustration *a Matchmark *b Unlock Position Mark *c Lock Position Mark
 |
| 8. INSTALL FRONT TURN SIGNAL LIGHT SOCKET |
Connect the connector to install the front turn signal light socket.
| 9. INSTALL FRONT TURN SIGNAL LIGHT BULB |
Install the front turn signal light bulb to the front turn signal light socket.
Align the matchmark of the front turn signal light socket with the unlock position mark, and then rotate the front turn signal light socket clockwise until the lock position mark to connect the front turn signal light socket.
Text in Illustration *a Matchmark *b Unlock Position Mark *c Lock Position Mark
 |