Seat Belt Control Ecu (For Rhd) Removal

Vehicle Interior. Land Cruiser. Urj200, 202 Grj200 Vdj200
Pre-Crash Safety. Land Cruiser. Urj200, 202 Grj200 Vdj200

  1. PRECAUTION

  2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL (w/ Passenger Side Knee Airbag)

  3. REMOVE NO. 1 INSTRUMENT PANEL FINISH CUSHION

  4. REMOVE LOWER INSTRUMENT PANEL PAD SUB-ASSEMBLY LH

  5. REMOVE NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (w/ Floor Under Cover)

  6. REMOVE FRONT PASSENGER SIDE KNEE AIRBAG ASSEMBLY (w/ Passenger Side Knee Airbag)

  7. REMOVE LOWER INSTRUMENT PANEL (w/o Passenger Side Knee Airbag)

  8. REMOVE NO. 3 INSTRUMENT CLUSTER FINISH PANEL GARNISH

  9. REMOVE LOWER NO. 2 INSTRUMENT PANEL FINISH PANEL

  10. REMOVE SEAT BELT CONTROL ECU

Seat Belt Control Ecu (For Rhd) -- Removal



1. PRECAUTION
NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).


2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL (w/ Passenger Side Knee Airbag)
CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


3. REMOVE NO. 1 INSTRUMENT PANEL FINISH CUSHION


Land Cruiser. Urj200, 202 Grj200 Vdj200.Pre-Crash Safety.Pre-Crash Safety System.Seat Belt Control Ecu (For Rhd) Removal

  1. Put protective tape around the No. 1 instrument panel finish panel cushion.

    Text in Illustration
    *1
    		Protective Tape

  1. Using a moulding remover, detach the 7 claws and remove the No. 1 instrument panel finish panel cushion.



4. REMOVE LOWER INSTRUMENT PANEL PAD SUB-ASSEMBLY LH


Land Cruiser. Urj200, 202 Grj200 Vdj200

  1. Remove the clip and screw.

  1. Detach the 8 claws.

  1. Disconnect the connectors, detach the 2 clamps and remove the lower instrument panel pad sub-assembly.



5. REMOVE NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (w/ Floor Under Cover)


Land Cruiser. Urj200, 202 Grj200 Vdj200

  1. Detach the 4 claws and remove the No. 2 instrument panel under cover.



6. REMOVE FRONT PASSENGER SIDE KNEE AIRBAG ASSEMBLY (w/ Passenger Side Knee Airbag)


    Land Cruiser. Urj200, 202 Grj200 Vdj200.Pre-Crash Safety.Pre-Crash Safety System.Seat Belt Control Ecu (For Rhd) Removal

  1. Remove the 4 bolts.

  1. Detach the 4 claws and remove the front passenger side knee airbag.

  1. Disconnect the connector.

    NOTICE:
    When handling the airbag connector, take care not to damage the airbag wire harness.


7. REMOVE LOWER INSTRUMENT PANEL (w/o Passenger Side Knee Airbag)


Land Cruiser. Urj200, 202 Grj200 Vdj200

  1. Detach the 2 claws and disconnect the DLC3.

  1. Remove the 5 bolts and lower instrument panel.



8. REMOVE NO. 3 INSTRUMENT CLUSTER FINISH PANEL GARNISH


Land Cruiser. Urj200, 202 Grj200 Vdj200.Pre-Crash Safety.Pre-Crash Safety System.Seat Belt Control Ecu (For Rhd) Removal

  1. Place protective tape as shown in the illustration.

    Text in Illustration
    *1
    		Protective Tape

  1. Using a moulding remover, detach the 6 claws and remove the No. 3 instrument cluster finish panel garnish.



9. REMOVE LOWER NO. 2 INSTRUMENT PANEL FINISH PANEL


Land Cruiser. Urj200, 202 Grj200 Vdj200

  1. Remove the 4 bolts.

  1. Detach the 3 claws.

  1. Disconnect the connector and remove the lower No. 2 instrument panel finish panel.



10. REMOVE SEAT BELT CONTROL ECU


Land Cruiser. Urj200, 202 Grj200 Vdj200

  1. Disconnect the 2 connectors.

  1. Remove the nut and ECU.