Headlight Leveling Ecu (For Lhd) -- Removal |
| 1. PRECAUTION |
- CAUTION:
- Be sure to read Precaution thoroughly before servicing (Click here).
- NOTICE:
- After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (- ) battery terminal notices before proceeding with work (Click here).
| 2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL |
- CAUTION:
- Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
- NOTICE:
- When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).
| 3. REMOVE NO. 1 INSTRUMENT PANEL FINISH CUSHION |
for Type A:
Put protective tape around the No. 1 instrument panel finish panel cushion.
Text in Illustration *a Protective Tape Using a moulding remover B, detach the 4 claws and 3 clips and remove the No. 2 instrument panel finish panel cushion.
for Type B:
Put protective tape around the No. 1 instrument panel finish panel cushion.
Text in Illustration *a Protective Tape Using a moulding remover, detach the 7 claws and remove the No. 2 instrument panel finish panel cushion.
| 4. REMOVE LOWER INSTRUMENT PANEL PAD SUB-ASSEMBLY RH |
for Type A:
Put protective tape around the lower instrument panel pad sub-assembly RH.
Text in Illustration *a Protective Tape Remove the clip and screw.
Detach the 11 claws and guide and remove the lower instrument panel pad sub-assembly RH.
for Type B:
Put protective tape around the lower instrument panel pad sub-assembly RH.
Text in Illustration *a Protective Tape Remove the clip and screw.
Detach the 7 claws and remove the lower instrument panel pad sub-assembly RH.
| 5. REMOVE INSTRUMENT SIDE PANEL RH |
 |
Put protective tape around the instrument side panel RH.
Text in Illustration *a Protective Tape
Using a moulding remover A, detach the 6 claws and remove the instrument side panel RH.
w/ Airbag Cut Off Switch:
Disconnect the connector and remove the instrument side panel RH.
| 6. REMOVE NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY |
 |
Detach the 4 claws and 3 guides.
Disconnect the connector and remove the No. 2 instrument panel under cover sub-assembly.
| 7. REMOVE FRONT DOOR SCUFF PLATE RH |
- HINT:
- Use the same procedures described for the LH side.
| 8. REMOVE COWL SIDE TRIM BOARD RH |
| 9. REMOVE LOWER NO. 2 INSTRUMENT PANEL AIRBAG ASSEMBLY |
Remove the 4 bolts.
 |
Detach the 4 claws and remove the front passenger side knee airbag assembly.
Using a screwdriver, release the connector lock and disconnect the airbag connector.
Text in Illustration *a Connector Lock 
Protective Tape - NOTICE:
- When handling the airbag connector, take care not to damage the airbag wire harness.
- CAUTION:
- Tape the screwdriver tip before use.
| 10. REMOVE NO. 3 INSTRUMENT CLUSTER FINISH PANEL GARNISH |
 |
Put protective tape around the No. 3 instrument cluster finish panel garnish.
Text in Illustration *a Protective Tape
Using a moulding remover A, detach the 6 claws and remove the No. 3 instrument cluster finish panel garnish.
| 11. REMOVE INSTRUMENT PANEL BOX DOOR KNOB |
- HINT:
- Use the same procedure for both instrument panel box door knobs.
Using a moulding remover B, detach the 2 claws and remove the instrument panel box door knob.
 |
| 12. REMOVE LOWER NO. 2 INSTRUMENT PANEL FINISH PANEL |
 |
Put protective tape around the lower No. 2 instrument panel finish panel.
Remove the 4 screws <C>.
Text in Illustration *a Protective Tape *b Screw <C>
Detach the 3 claws.
 |
Disconnect the connector and remove the lower No. 2 instrument panel finish panel.
| 13. REMOVE HEADLIGHT SWIVEL ECU ASSEMBLY |
Disconnect the connector.
 |
Remove the nut and headlight swivel ECU assembly.