Exterior Panels Trim. Black Out Tape (For Rear Door) Removal

Vehicle Exterior. Land Cruiser. Urj200, 202 Grj200 Vdj200

Exterior Panels Trim. Land Cruiser. Urj200, 202 Grj200 Vdj200

Black Out Tape (For Rear Door) -- Removal

HINT:

Use the same procedure for the RH and LH sides.
The procedure listed below is for the LH side.
When removing the No. 2 black out tape LH, No. 6 black out tape LH, upper inner black out tape LH, rear inner black out tape LH, and rear door front window frame moulding LH, heat the vehicle body, No. 2 black out tape LH, No. 6 black out tape LH, upper inner black out tape LH, rear inner black out tape LH, and rear door front window frame moulding LH using a heat light.

Standard Heating Temperature:

Item	Temperature
Vehicle Body	40 to 60°C (104 to 140°F)
No. 2 Black Out Tape LH	20 to 30°C (68 to 86°F)
No. 6 Black Out Tape LH	20 to 30°C (68 to 86°F)
Upper Inner Black Out Tape LH	20 to 30°C (68 to 86°F)
Rear Inner Black Out Tape LH	20 to 30°C (68 to 86°F)
Rear Door Front Window Frame Moulding LH	20 to 30°C (68 to 86°F)

NOTICE:

Do not heat the vehicle body, No. 2 black out tape LH, No. 6 black out tape LH, upper inner black out tape LH, rear inner black out tape LH, and rear door front window frame moulding LH excessively.

1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).

2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

3. REMOVE REAR DOOR INSIDE HANDLE BEZEL LH

Using a screwdriver, detach the 4 claws and remove the rear door inside handle bezel LH.
HINT:
Tape the screwdriver tip before use.
Text in Illustration

Protective Tape

Text in Illustration
	Protective Tape

4. REMOVE REAR DOOR UPPER ARMREST BASE PANEL LH

Using a moulding remover, detach the 7 claws.

Disconnect the connector and remove the rear door upper armrest base panel assembly LH.

5. REMOVE ASSIST GRIP COVER LH

Using a moulding remover, detach the 9 claws and remove the assist grip cover LH.

6. REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY LH

Land Cruiser. Urj200, 202 Grj200 Vdj200.Exterior Panels Trim.Front Bumper (For Standard).Black Out Tape (For Rear Door) Removal

Remove the 3 screws.

Remove the 9 clips.

Remove the rear inner door glass weatherstrip LH together with the rear door trim board sub-assembly LH by pulling them upward in the order shown in the illustration.
HINT:
Make sure that the pin labeled A in the illustration is detached from the door panel.

Disconnect the connector and remove the rear door trim board sub-assembly LH.

Disconnect the 2 cables from the rear door inside handle sub-assembly LH.

7. REMOVE REAR DOOR INNER GLASS WEATHERSTRIP LH

Detach the 4 clips and remove the rear door inner glass weatherstrip LH from the rear door trim board sub-assembly LH.
NOTICE:
1. Squeeze the metal clip to remove it.
2. The metal clip may be deformed if it is forcibly pulled.

8. REMOVE REAR DOOR SERVICE HOLE COVER LH

Using a clip remover, detach the 7clamps.

Remove the bolt and disconnect the 3connectors.

Remove the rear door service hole cover LH.
HINT:
Remove the remaining tape on the door.

9. REMOVE REAR DOOR GLASS RUN LH

Remove the rear door glass run LH from the window frame.

10. REMOVE REAR DOOR REAR LOWER WINDOW FRAME SUB-ASSEMBLY LH

Remove the 2 bolts.

Remove the screw and rear door rear lower window frame sub-assembly LH.

11. REMOVE REAR DOOR QUARTER WINDOW GLASS LH

Remove the rear door quarter window glass LH and rear door quarter window weatherstrip LH as a unit as shown in the illustration.

12. REMOVE REAR DOOR GLASS SUB-ASSEMBLY LH

Remove the rear door glass sub-assembly LH from the rear door window regulator sub-assembly LH as shown in the illustration.
NOTICE:
Do not damage the door glass.

13. REMOVE REAR DOOR BELT MOULDING ASSEMBLY LH

Put protective tape around the belt moulding.

Detach the claw and remove the belt moulding.

14. REMOVE REAR DOOR FRONT WINDOW FRAME MOULDING LH

Put protective tape around the window frame moulding.

Detach the clip and remove the double-sided tape to remove the window frame moulding.

15. REMOVE REAR DOOR FRAME GARNISH LH

Detach the clip and remove the rear door frame garnish LH.
HINT:
This clip needs to be replaced with a new one because the clip will break when removing the rear door frame garnish LH.

16. REMOVE REAR DOOR NO. 2 FRAME GARNISH LH

Detach the clip and remove the rear door No. 2 frame garnish LH.
HINT:
This clip needs to be replaced with a new one because the clip will break when removing the rear No. 2 door frame garnish LH.

17. REMOVE REAR DOOR CHECK ASSEMBLY LH

Remove the bolt, 2 nuts and rear door check assembly LH.
NOTICE:
Be careful when removing the bolt and nuts as the rear door check assembly LH may fall and become damaged.
HINT:
Remove the rear door check assembly LH through the service hole.

18. REMOVE REAR DOOR WEATHERSTRIP LH

w/o Spot Cover:
1. Detach the 4 clips, and remove the upper part of the rear door weatherstrip LH so that the black out tape can be removed.

w/ Spot Cover:
1. Remove the rear door weatherstrip LH (Click here).

19. REMOVE NO. 2 BLACK OUT TAPE LH

Pull back an edge of the No. 2 black out tape LH and pull it parallel to the vehicle body to remove it.

20. REMOVE NO. 6 BLACK OUT TAPE LH

Pull back an edge of the No. 6 black out tape LH and pull it parallel to the vehicle body to remove it.

21. REMOVE UPPER INNER BLACK OUT TAPE LH

Pull back an edge of the upper inner black out tape LH and pull it parallel to the vehicle body to remove it.

22. REMOVE REAR INNER BLACK OUT TAPE LH

Pull back an edge of the rear inner black out tape LH and pull it parallel to the vehicle body to remove it.