Steering Column Assembly (For Power Tilt And Power Telescopic Steering Column) Installation

Align the part of the dust cover labeled A with the No. 2 steering intermediate shaft, and install the No. 2 steering intermediate shaft assembly to the steering link assembly.

Install the bolt.

Torque:

35 N*m{357 kgf*cm, 26 ft.*lbf}

NOTICE:

Be careful not to damage the dust cover.

Install the 4 bolts and nut.

Torque:

5.0 N*m{51 kgf*cm, 44 in.*lbf}

NOTICE:

Do not fold back the boot part of the steering hole cover or extend it excessively. if it is extended excessively, return it to its original position.

HINT:

Install the steering intermediate shaft assembly from the inside of the vehicle.

Install the clamp to the steering column hole cover.

Make sure that the power steering link assembly is centered.

Install the steering actuator assembly.

1. If installing a new steering actuator assembly:
   Install the steering actuator assembly with the white paint on the upper surface of the spiral case facing down.
   

   NOTICE:

   Do not pull out the center lock pin.





2. If reinstalling the removed steering actuator assembly:
   

   1. Slowly turn the spiral case clockwise until it locks.
      
   2. Turn the spiral case two turns counterclockwise from the lock position.
      
   3. Align the slit of the sliding yoke with the alignment mark (▲).
      
   4. Install the steering actuator assembly with the white paint on the upper surface of the spiral case facing down.
      

Align the matchmarks on the No. 2 steering intermediate shaft and steering actuator.

NOTICE:

1. Do not fold back the boot part of the steering hole cover or turn it excessively. If it is turned excessively, return it to its original position.
   
2. Do not turn the actuator body and the spiral case.
   

HINT:

Install the steering actuator from the inside of the vehicle.

Install the bolt.

Torque:

35 N*m{360 kgf*cm, 26 ft.*lbf}

Using needle nose pliers, lock the clamp to the steering column hole cover to install it.

NOTICE:

Be careful when performing the operation as the clamp may not lock if the claws of the clamp are deformed.

Move the lock in the direction of the arrow and connect the steering actuator connector.

HINT:

When a new actuator is installed, remove the center lock pin.

Connect the connector.

Install the 4 nuts and steering column.

Torque:

26 N*m{265 kgf*cm, 19 ft.*lbf}

Attach the 2 claws to install the duct.

Install the clip.

Attach the 3 claws and install the wiring harness protector and wire harness.

Connect the connector.

NOTICE:

When handling the airbag connector, take care not to damage the airbag wire harness.

Install the driver side knee airbag with the 5 bolts.

Torque:

10 N*m{102 kgf*cm, 7 ft.*lbf}

Attach the 2 claws and connect the DLC3.

Install the lower instrument panel with the 5 bolts.

Connect the connectors.

Attach the 4 claws to install the No. 1 switch hole base.

Connect the connectors.

for Automatic Air Conditioning System:

1. Attach the 2 claws to install the room temperature sensor.
   

Attach the 2 claws to connect the 2 control cables.

w/ Driver Side Knee Airbag:

1. Attach the 16 claws to install the lower No. 1 instrument panel finish panel.
   





2. Install the 2 bolts.
   
   

   
   
   
   

w/o Driver Side Knee Airbag:

1. Attach the 9 claws to install the lower No. 1 instrument panel finish panel.
   





2. Install the 2 bolts.
   
   

   
   
   
   

Attach the 2 claws to close the hole cover.

Attach the 2 clips to install the cowl side trim board.

Install the cap nut.

Connect the connectors.

Attach the 3 claws to install the No. 1 instrument panel under cover.

Install the 2 screws.

Attach the 3 claws and 4 clips to install the scuff plate.

Install the screw.

Connect the connector.

Attach the 9 claws to install the instrument cluster finish panel.

Attach the 9 claws to install the instrument cluster finish panel.

Attach the 2 claws to install the No. 2 instrument cluster finish panel garnish.

Attach the 3 claws to install the No. 1 instrument cluster finish panel garnish.

Attach the 6 claws to install the instrument side panel.

Connect the connectors and 2 clamps.

Attach the 8 claws to install the panel pad.

Install the screw.

Install the clip.

Attach the 7 claws to install the panel cushion.

Using pliers, grip the claws of the clamp and install the turn signal switch assembly with spiral cable sub-assembly to the steering column assembly with the clamp.

Connect the 5 connectors to the turn signal switch with spiral cable.

Attach the claw to install the switch.

Connect the switch connector.

Attach the claw to install the upper steering column cover.

Attach the 4 clips to install the upper steering column cover onto the instrument cluster finish panel.

Attach the 2 claws to install the lower steering column cover.

NOTICE:

Do not damage the tilt and telescopic switch.

Install the 3 screws.

Torque:

1.5 N*m{15 kgf*cm, 13 in.*lbf}

Align the matchmarks on the steering wheel assembly and steering main shaft assembly.

Install the steering wheel assembly set nut.

Torque:

50 N*m{510 kgf*cm, 37 ft.*lbf}

Support the steering pad with one hand.

Connect the 2 connectors to the steering pad.

NOTICE:

When handling the airbag connector, take care not to damage the airbag wire harness.

Connect the horn connector.

Confirm that the circumference groove of the "TORX" screw fits in the screw case, and place the steering pad onto the steering wheel.

Using a T30 "TORX" socket wrench, tighten the 2 screws.

Torque:

8.8 N*m{90 kgf*cm, 78 in.*lbf}

Attach the 2 claws to install the cover.

Attach the 2 claws to install the cover.

Inspect the SRS warning light (Click here).