Entry Lock And Unlock Switch (For Rear) Removal

Vehicle Interior. Land Cruiser. Urj200, 202 Grj200 Vdj200
Theft Deterrent Keyless Entry. Land Cruiser. Urj200, 202 Grj200 Vdj200

  1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

  2. REMOVE REAR DOOR ARMREST BASE PANEL ASSEMBLY LH

  3. REMOVE REAR DOOR INSIDE HANDLE BEZEL LH

  4. REMOVE ASSIST GRIP COVER LH

  5. REMOVE COURTESY LIGHT ASSEMBLY (w/ Courtesy Light)

  6. REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY LH

  7. REMOVE REAR DOOR SERVICE HOLE COVER LH

  8. REMOVE REAR DOOR LOCK ASSEMBLY LH

  9. REMOVE REAR DOOR OUTSIDE HANDLE COVER LH

  10. REMOVE REAR DOOR OUTSIDE HANDLE ASSEMBLY LH

Entry Lock And Unlock Switch (For Rear) -- Removal


HINT:
  1. Use the same procedures for the LH side and RH side.
  2. The procedures listed below are for the LH side.


1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


2. REMOVE REAR DOOR ARMREST BASE PANEL ASSEMBLY LH


    Land Cruiser. Urj200, 202 Grj200 Vdj200

  1. Using a moulding remover, detach the 7 claws.

  1. Disconnect the connector and remove the armrest base panel.



3. REMOVE REAR DOOR INSIDE HANDLE BEZEL LH


    Land Cruiser. Urj200, 202 Grj200 Vdj200.Theft Deterrent Keyless Entry.Entry And Start System (For Entry Function).Entry Lock And Unlock Switch (For Rear) Removal

  1. Using a screwdriver, detach the 4 claws and remove the rear door inside handle bezel LH.

    HINT:
    Tape the screwdriver tip before use.
    Text in Illustration
    *1
    		Protective Tape


4. REMOVE ASSIST GRIP COVER LH


    Land Cruiser. Urj200, 202 Grj200 Vdj200

  1. Using a moulding remover, detach the 9 claws and remove the assist grip cover LH.



5. REMOVE COURTESY LIGHT ASSEMBLY (w/ Courtesy Light)


    Land Cruiser. Urj200, 202 Grj200 Vdj200

  1. Detach the claw.

  1. Remove the courtesy light and then disconnect the connector.



6. REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY LH


    Land Cruiser. Urj200, 202 Grj200 Vdj200.Theft Deterrent Keyless Entry.Entry And Start System (For Entry Function).Entry Lock And Unlock Switch (For Rear) Removal

  1. Remove the 3 screws.

  1. Remove the 9 clips.

  1. Remove the rear inner door glass weatherstrip LH together with the rear door trim board sub-assembly LH by pulling them upward in the order shown in the illustration.

    HINT:
    Make sure that the pin labeled A in the illustration is detached from the door panel.

  1. Disconnect the connector and remove the rear door trim board sub-assembly LH.



    Land Cruiser. Urj200, 202 Grj200 Vdj200

  1. Disconnect the 2 cables from the rear door inside handle sub-assembly LH.



7. REMOVE REAR DOOR SERVICE HOLE COVER LH


    Land Cruiser. Urj200, 202 Grj200 Vdj200.Theft Deterrent Keyless Entry.Entry And Start System (For Entry Function).Entry Lock And Unlock Switch (For Rear) Removal

  1. Using a clip remover, detach the 6 clamps.

  1. Remove the bolt and disconnect the 2 connectors.

  1. Remove the rear door service hole cover LH.

    HINT:
    Remove the remaining tape on the door.


8. REMOVE REAR DOOR LOCK ASSEMBLY LH


    Land Cruiser. Urj200, 202 Grj200 Vdj200

  1. Using a T30 ''TORX'' socket, remove the 3 screws and door lock.

    NOTICE:
    Be careful when removing the screws as the door lock may fall and become damaged.


9. REMOVE REAR DOOR OUTSIDE HANDLE COVER LH


    Land Cruiser. Urj200, 202 Grj200 Vdj200

  1. Using a T30 ''TORX'' socket, loosen the screw.



    Land Cruiser. Urj200, 202 Grj200 Vdj200

  1. Detach the claw and remove the rear door outside handle cover LH.



10. REMOVE REAR DOOR OUTSIDE HANDLE ASSEMBLY LH


    Land Cruiser. Urj200, 202 Grj200 Vdj200

  1. Using a T30 "TORX" wrench, loosen the screw.

  1. Disconnect the connector.



    Land Cruiser. Urj200, 202 Grj200 Vdj200

  1. Remove the handle by sliding and pulling it in the direction indicated by the arrow in the illustration.