Entry Lock And Unlock Switch (For Rear) Installation

Vehicle Interior. Land Cruiser. Urj200, 202 Grj200 Vdj200
Theft Deterrent Keyless Entry. Land Cruiser. Urj200, 202 Grj200 Vdj200

  1. INSTALL REAR DOOR OUTSIDE HANDLE ASSEMBLY LH

  2. INSTALL REAR DOOR OUTSIDE HANDLE COVER LH

  3. INSTALL REAR DOOR LOCK ASSEMBLY LH

  4. INSTALL REAR DOOR SERVICE HOLE COVER LH

  5. INSTALL COURTESY LIGHT ASSEMBLY (w/ Courtesy Light)

  6. INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY LH

  7. INSTALL ASSIST GRIP COVER LH

  8. INSTALL REAR DOOR INSIDE HANDLE BEZEL LH

  9. INSTALL REAR DOOR ARMREST BASE PANEL ASSEMBLY LH

  10. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Entry Lock And Unlock Switch (For Rear) -- Installation


HINT:
  1. Use the same procedures for the LH side and RH side.
  2. The procedures listed below are for the LH side.


1. INSTALL REAR DOOR OUTSIDE HANDLE ASSEMBLY LH


    Land Cruiser. Urj200, 202 Grj200 Vdj200

  1. Insert the front end of the rear door outside handle assembly into the rear door outside handle frame.

    NOTICE:
    If the bellcrank lever is not pulled and held when installing the outside handle, the bellcrank lever will interfere with the outside handle and the release plate may be damaged.

  1. Insert the rear end of the rear door outside handle assembly into the rear door outside handle frame. Next, slide the rear door outside handle assembly toward the front of the vehicle to install it.



    Land Cruiser. Urj200, 202 Grj200 Vdj200

  1. Using a T30 ''TORX'' socket, tighten the screw.

  1. Connect the connector.



2. INSTALL REAR DOOR OUTSIDE HANDLE COVER LH

  1. Attach the claw to install the rear door outside handle cover LH.

  1. Using a T30 ''TORX'' socket, install the rear door outside handle cover LH with the screw.



3. INSTALL REAR DOOR LOCK ASSEMBLY LH


    Land Cruiser. Urj200, 202 Grj200 Vdj200

  1. Apply MP grease to the sliding parts of the rear door lock assembly.

  1. Insert the rear door lock assembly to the rear door outside handle release plate, and set it to the rear door panel.

  1. Make sure that the rear door outside handle frame release plate is securely connected to the rear door lock assembly.

  1. Using a T30 ''TORX'' wrench, the 3 screws.

    Torque:
    5.0 N*m{51 kgf*cm, 44 in.*lbf}


4. INSTALL REAR DOOR SERVICE HOLE COVER LH

  1. Apply butyl tape to the door.



    Land Cruiser. Urj200, 202 Grj200 Vdj200

  1. Pass the rear door lock remote control cable assembly LH and rear door inside locking cable assembly LH through a new rear door service hole cover LH.

    NOTICE:
    1. When installing the rear door service hole cover LH, pull the links and connectors through the rear door service hole cover LH.
    2. There should be no wrinkles or folds after attaching the rear door service hole cover LH.
    3. After attaching the rear door service hole cover LH, check the sealing quality.

  1. Connect the 2 connectors.

  1. Attach the 6 clamps.



    Land Cruiser. Urj200, 202 Grj200 Vdj200.Theft Deterrent Keyless Entry.Entry And Start System (For Entry Function).Entry Lock And Unlock Switch (For Rear) Installation

  1. Install the bolt as shown in the illustration.

    Torque:
    8.4 N*m{86 kgf*cm, 74 in.*lbf}


5. INSTALL COURTESY LIGHT ASSEMBLY (w/ Courtesy Light)


    Land Cruiser. Urj200, 202 Grj200 Vdj200

  1. Connect the connector.

  1. Attach the claw of the courtesy light to the rear door trim.



6. INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY LH

  1. Connect the connector.



    Land Cruiser. Urj200, 202 Grj200 Vdj200

  1. Connect the rear door lock remote control cable assembly LH and rear door inside locking cable assembly LH to the rear door inside handle sub-assembly LH.



    Land Cruiser. Urj200, 202 Grj200 Vdj200

  1. Attach the 4 claws and 9 clips to install the rear door trim board sub-assembly LH.

  1. Install the 3 screws.



7. INSTALL ASSIST GRIP COVER LH

  1. Attach the 9 claws to install the assist grip cover LH to the rear door trim board sub-assembly LH.



8. INSTALL REAR DOOR INSIDE HANDLE BEZEL LH

  1. Attach the 4 claws to install the rear door inside handle bezel LH.



9. INSTALL REAR DOOR ARMREST BASE PANEL ASSEMBLY LH

  1. Connect the connector.



    Land Cruiser. Urj200, 202 Grj200 Vdj200

  1. Attach the 7 claws to install the armrest base panel.



10. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).