Rear No. 1 Seat Inner Belt Assembly (For 60/40 Split Seat Type 60 Side) Removal
Seat Belt. Land Cruiser. Urj200, 202 Grj200 Vdj200
REMOVE REAR NO. 1 SEAT ASSEMBLY LH
REMOVE SEAT ADJUSTER BOLT COVER
REMOVE RECLINING ADJUSTER RELEASE HANDLE LH
REMOVE REAR NO. 1 SEAT RECLINING COVER LH
REMOVE REAR NO. 1 SEAT RECLINING COVER RH
REMOVE UPPER SEAT TRACK RAIL COVER LH
REMOVE UPPER SEAT TRACK RAIL COVER RH
REMOVE REAR NO. 2 SEAT LEG SIDE COVER
REMOVE REAR NO. 2 SEAT PROTECTOR
REMOVE REAR NO. 1 SEAT HINGE SUB-ASSEMBLY LH
REMOVE REAR NO. 1 SEAT HINGE SUB-ASSEMBLY RH
REMOVE SEAT BELT ANCHOR COVER CAP
REMOVE REAR SEATBACK STAY COVER LH
REMOVE REAR UNDER SIDE COVER LH
REMOVE REAR SEAT CUSHION COVER RH
REMOVE REAR SEAT UNDER TRAY LH COVER
REMOVE REAR NO. 1 SEAT INNER BELT ASSEMBLY LH
DISCONNECT NO. 1 SEAT 3 POINT TYPE BELT ASSEMBLY LH
Rear No. 1 Seat Inner Belt Assembly (For 60/40 Split Seat Type 60 Side) -- Removal |
- HINT:
- Use the same procedure for RHD and LHD vehicles.
- The procedure listed below is for LHD vehicles.
| 1. REMOVE REAR NO. 1 SEAT ASSEMBLY LH |
Remove the rear No. 1 seat assembly (Click here).
| 2. REMOVE SEAT ADJUSTER BOLT COVER |
Using a screwdriver, detach the 2 claws and remove the cover.
- HINT:
- Tape the screwdriver tip before use.
| 3. REMOVE RECLINING ADJUSTER RELEASE HANDLE LH |
Remove the screw and release handle.
| 4. REMOVE REAR NO. 1 SEAT RECLINING COVER LH |
Remove the 2 screws.
Detach the 3 claws in the order shown in the illustration, and then remove the cover.
| 5. REMOVE REAR NO. 1 SEAT RECLINING COVER RH |
Remove the 2 screws.
Detach the 4 claws and remove the cover.
| 6. REMOVE UPPER SEAT TRACK RAIL COVER LH |
Using a screwdriver, detach the 2 claws and remove the cover.
- HINT:
- Tape the screwdriver tip before use.
| 7. REMOVE UPPER SEAT TRACK RAIL COVER RH |
Using a screwdriver, detach the 2 claws and remove the cover.
- HINT:
- Tape the screwdriver tip before use.
| 8. REMOVE REAR NO. 2 SEAT LEG SIDE COVER |
Remove the 4 screws and detach the 4 claws.
Remove the bolt that is securing the fold seat stopper band and remove the seat leg side cover together with the fold seat stopper band.
| 9. REMOVE REAR NO. 2 SEAT PROTECTOR |
w/ Rear Seat Side Airbag:
Detach the claw and remove the wire harness connector.
w/ Seat Heater System:
Detach the claw and remove the wire harness connector.
Using a clip remover, remove the clip.
Detach the claw and remove the seat protector from the seat hinge.
Detach the 2 claws, open the protector and remove wire harness.
| 10. REMOVE REAR NO. 1 SEAT HINGE SUB-ASSEMBLY LH |
w/ Rear Seat Side Airbag:
Detach the wire harness clamp.
w/ Seat Heater System:
Detach the wire harness clamp.
Remove the 2 nuts and hinge.
Detach the cable clamp and disconnect the cable.
| 11. REMOVE REAR NO. 1 SEAT HINGE SUB-ASSEMBLY RH |
Remove the 2 nuts and hinge.
| 12. REMOVE SEAT BELT ANCHOR COVER CAP |
Detach the claw and open the cap.
Remove the screw and anchor cover cap.
| 13. REMOVE REAR SEATBACK STAY COVER LH |
Remove the screw.
Detach the 2 claws and remove the cover.
| 14. REMOVE REAR UNDER SIDE COVER LH |
Detach the 10 claws.
Remove the 5 screws.
Detach the 2 clips and 2 claws, and remove the cover.
| 15. REMOVE REAR SEAT CUSHION COVER RH |
Remove the 4 screws.
Detach the 2 claws and remove the cover.
| 16. REMOVE REAR SEAT UNDER TRAY LH COVER |
Remove the 2 screws.
Detach the 4 claws and remove the cover.
| 17. REMOVE REAR NO. 1 SEAT INNER BELT ASSEMBLY LH |
Remove the bolt and belt.
- HINT:
- The No. 1 seat 3 point type belt anchor is fixed with the same bolt as the rear No. 1 seat inner belt LH. Therefore, it becomes disconnected when the bolt is removed.
| 18. DISCONNECT NO. 1 SEAT 3 POINT TYPE BELT ASSEMBLY LH |
Disconnect the belt anchor.
