Lumbar Support Adjuster Assembly (For Power Seat) -- Installation |
- CAUTION:
- Wear protective gloves. Sharp areas on the parts may injure your hands.
- HINT:
- Use the same procedure for RHD and LHD vehicles.
- The procedure listed below is for LHD vehicles.
| 1. INSTALL LUMBAR SUPPORT ADJUSTER ASSEMBLY LH |
Install the lumbar support adjuster assembly LH with the 2 screws.
 |
Connect the connector.
Attach the 4 hooks to install the seatback spring.
Text in Illustration *1 Cable Clamp *2 Hook
 |
Install the 4 springs.
Connect the active headrest cable to the seatback spring with the cable clamp.
| 2. INSTALL FRONT SEATBACK PROTECTOR |
 |
Apply double-sided tape as shown in the illustration.
Text in Illustration *1 Double-sided tape
Install the front seatback protector.
| 3. INSTALL SEATBACK COVER WITH PAD |
 |
Attach the hooks to install the seatback cover with pad.
Text in Illustration *1 Hog Ring *2 Hog Ring Pliers
Attach the seatback cover bracket with the nut.
Text in Illustration *1 Seatback Cover Bracket - Torque:
- 5.0 N*m{51 kgf*cm, 44 in.*lbf}
- CAUTION:
- After the seatback cover with pad is installed, make sure the seatback cover bracket is not twisted.
 |
Using hog ring pliers, install new hog rings.
- NOTICE:
- Be careful not to damage the cover.
w/o Climate Control Seat System:
Connect the connector and attach the 2 wire harness clamps.
 |
w/ Climate Control Seat System:
Connect the 2 connectors and attach the 4 wire harness clamps.
 |
| 4. INSTALL FRONT SEAT HEADREST SUPPORT |
 |
Attach the 4 claws to install the 2 front seat headrest supports.
| 5. INSTALL SEAT CLIMATE CONTROL CONTROLLER LH (w/ Climate Control Seat System) |
 |
Install the seat climate control controller LH with the 2 screws.
Attach the wire harness clamp.
Attach the 4 claws to connect the seat climate control blower LH.
 |
| 6. INSTALL FRONT SEATBACK BOARD SUB-ASSEMBLY LH |
 |
Move the front seatback board sub-assembly in the direction of the arrow to attach the 2 hooks and install it.
Install the 2 screws.
| 7. INSTALL FRONT INNER SEAT CUSHION SHIELD LH |
 |
Attach the 2 claws and clip to install the front inner seat cushion shield LH.
Install the screw.
| 8. INSTALL FRONT SEAT INNER BELT ASSEMBLY LH |
Install the front seat belt anchor plate.
Install the front seat inner belt assembly with the nut.
- Torque:
- 42 N*m{428 kgf*cm, 31 ft.*lbf}
- NOTICE:
- Do not allow the anchor part of the front seat inner belt assembly to overlap the protruding parts of the front seat adjuster.
 |
Connect the connectors and attach the clamps.
| 9. INSTALL FRONT SEAT CUSHION SHIELD LH |
for Driver Side:
Connect the connector.
Attach the 2 claws to install the front seat cushion shield LH together with the front inner No. 1 cushion shield LH.
 |
Install the 3 screws.
Connect the 2 rubber bands.
 |
Install the 2 screws.
| 10. INSTALL RECLINING POWER SEAT SWITCH KNOB |
 |
Attach the 2 claws to install the reclining power seat switch knob.
| 11. INSTALL SLIDE AND VERTICAL POWER SEAT SWITCH KNOB |
 |
Attach the 2 claws to install the slide and vertical power seat switch knob.
| 12. INSTALL FRONT SEAT ASSEMBLY LH |