INSTALL SEAT HEATER CONTROL SUB-ASSEMBLY LH (w/ Seat Heater System)
INSTALL REAR SEAT CUSHION HOLDER BRACKET LH (w/ Seat Heater System)
INSTALL REAR CENTER SEAT ARMREST CUP HOLDER SUB-ASSEMBLY (w/ Center Armrest)
INSTALL SEAT CENTER ARMREST BRACKET SUB-ASSEMBLY (w/ Center Armrest)
INSTALL REAR CENTER SEAT ARMREST DOOR SUB-ASSEMBLY (w/ Center Armrest)
INSTALL REAR CENTER SEAT ARMREST BOX ASSEMBLY (w/ Center Armrest)
INSTALL REAR CENTER SEAT ARMREST PANEL SUB-ASSEMBLY (w/ Center Armrest)
INSTALL REAR CENTER SEAT ARMREST ASSEMBLY (w/ Center Armrest)
INSTALL REAR CENTER SEAT HEADREST ASSEMBLY (w/ Center Armrest)
INSTALL REAR SEATBACK HEATER ASSEMBLY (w/ Seat Heater System)
INSTALL REAR SEAT CUSHION HEATER ASSEMBLY (w/ Seat Heater System)
Rear No. 1 Seat Assembly (For 60/40 Split Seat Type 60 Side) -- Reassembly |
- CAUTION:
- Wear protective gloves. Sharp areas on the parts may injure your hands.
- HINT:
- Use the same procedure for RHD and LHD vehicles.
- The procedure listed below is for LHD vehicles.
| 1. INSTALL REAR SEAT LOCK CONTROL LEVER LH |
 |
Install the lock control lever with the bolt.
- Torque:
- 13 N*m{133 kgf*cm, 10 ft.*lbf}
| 2. INSTALL REAR SEAT CUSHION FRAME SUB-ASSEMBLY LH |
 |
Temporarily install the seat cushion frame with the 5 nuts and bolt.
Tighten the 5 nuts.
- Torque:
- 42 N*m{428 kgf*cm, 31 ft.*lbf}
Using a T40 "TORX" socket, tighten the bolt.
- Torque:
- 21 N*m{214 kgf*cm, 15 ft.*lbf}
| 3. INSTALL NO. 1 SEAT LEG ASSEMBLY LH |
 |
Using a T40 "TORX" socket, install the seat leg assembly with the 2 bolts.
- Torque:
- 21 N*m{214 kgf*cm, 15 ft.*lbf}
| 4. INSTALL REAR SEAT INNER BELT ASSEMBLY |
 |
Install the seat belt with the bolt.
- Torque:
- 42 N*m{428 kgf*cm, 31 ft.*lbf}
- NOTICE:
- The anchor part of the seat belt must not overlap the protruding part.
| 5. INSTALL SEAT HEATER CONTROL SUB-ASSEMBLY LH (w/ Seat Heater System) |
 |
Attach the 2 claws to install the seat heater control.
| 6. INSTALL REAR SEAT CUSHION HOLDER BRACKET LH (w/ Seat Heater System) |
 |
Install the holder bracket with the 2 screws.
Connect the seat wire connector.
| 7. INSTALL REAR NO. 1 SEAT LOCK CABLE ASSEMBLY |
Attach the clamp to install the seat lock cable.
 |
Attach the 3 cable clamps to connect the 3 cables.
Connect the cable and install a new cable tie.
Install the lower seat track bracket with the 2 nuts.
- Torque:
- 21 N*m{214 kgf*cm, 15 ft.*lbf}
 |
| 8. INSTALL FOLD SEAT LOCK CONTROL CABLE SUB-ASSEMBLY |
 |
Install the 2 fold seat lock control cables.
Attach the 2 cable clamps to connect the 2 cables.
| 9. INSTALL REAR SEATBACK FRAME SUB-ASSEMBLY LH |
Install the lower seatback cover.
 |
Temporarily install the seatback frame with the 4 bolts.
 |
LH Side:
Using a T40 "TORX" socket, tighten the 2 bolts.- Torque:
- 42 N*m{428 kgf*cm, 31 ft.*lbf}
RH Side:
Using a T55 "TORX" socket, tighten the 2 bolts.- Torque:
- 42 N*m{428 kgf*cm, 31 ft.*lbf}
| 10. INSTALL NO. 2 FOLD SEAT LOCK CONTROL CABLE ASSEMBLY |
 |
Attach the clamp to install the lock control cable.
Attach the 2 cable clamps to connect the cable.
| 11. INSTALL RECLINING ADJUSTING CABLE ASSEMBLY LH |
 |
Attach the clamp to install the adjusting cable.
Attach the 2 cable clamps to connect the cable.
| 12. INSTALL NO. 1 SEAT 3 POINT TYPE BELT ASSEMBLY LH |
 |
Install the belt with the nut labeled A.
- Torque:
- 42 N*m{428 kgf*cm, 31 ft.*lbf}
Install the belt sensor with the 3 nuts labeled B.
| 13. INSTALL REAR SEAT SHOULDER BELT HOLE COVER LH |
 |
Install the seat belt as shown in the illustration.
Attach the 3 claws to install the shoulder belt hole cover.
 |
| 14. INSTALL REAR LOWER SEATBACK COVER SUB-ASSEMBLY LH |
 |
Attach the 4 claws to install the cover.
Install the 4 screws.
| 15. INSTALL REAR SEATBACK HINGE COVER LH |
 |
Attach the claw to install the cover.
Install the screw.
| 16. INSTALL REAR NO. 1 SEAT RECLINING COVER RH |
 |
Attach the claw to install the cover.
Install the screw.
| 17. INSTALL REAR NO. 2 SEAT RECLINING COVER LH |
 |
Attach the clamp to install the cover.
Install the screw.
| 18. INSTALL REAR SEAT RECLINING COVER LH |
 |
Attach the claw to install the cover.
Install the screw.
| 19. INSTALL REAR CENTER SEAT ARMREST CUP HOLDER SUB-ASSEMBLY (w/ Center Armrest) |
Install the 2 screws.
 |
Attach the 2 claws and install the rear center seat armrest cup holder sub-assembly.
| 20. INSTALL SEAT CENTER ARMREST BRACKET SUB-ASSEMBLY (w/ Center Armrest) |
Install the seat center armrest bracket sub-assembly.
| 21. INSTALL REAR CENTER SEAT ARMREST DOOR SUB-ASSEMBLY (w/ Center Armrest) |
Install the 2 nuts.
 |
Attach the 3 clips and install the rear center seat armrest door sub-assembly.
| 22. INSTALL REAR SEATBACK MOULDING LH (w/ Center Armrest) |
Attach the guide and claw.
 |
Install the rear seatback moulding LH.
| 23. INSTALL REAR SEATBACK MOULDING RH (w/ Center Armrest) |
Install the guide and claw.
 |
Install the rear seatback moulding RH.
| 24. INSTALL REAR CENTER SEAT ARMREST BOX ASSEMBLY (w/ Center Armrest) |
Install the rear center seat armrest box assembly.
| 25. INSTALL REAR CENTER SEAT ARMREST PANEL SUB-ASSEMBLY (w/ Center Armrest) |
Attach the 2 guides.
 |
Attach the 6 claws and rear center seat armrest panel sub-assembly.
| 26. INSTALL REAR CENTER SEAT ARMREST ASSEMBLY (w/ Center Armrest) |
 |
Using a T40 "TORX" socket, install the center seat armrest with the 2 bolts.
- Torque:
- 42 N*m{428 kgf*cm, 31 ft.*lbf}
| 27. INSTALL SEATBACK STOPPER PLATE |
w/ Center Armrest:
Install the bush to the stopper plate.
Temporarily install the stopper plate with the 3 bolts.
Using a T40 "TORX" socket, tighten the 2 bolts.
- Torque:
- 42 N*m{428 kgf*cm, 31 ft.*lbf}
Tighten the bolt.
- Torque:
- 15 N*m{153 kgf*cm, 11 ft.*lbf}
w/o Center Armrest:
Install the bush to the stopper plate.
Temporarily install the stopper plate with the 3 bolts.
Using a T40 "TORX" socket, tighten the 2 bolts.
- Torque:
- 42 N*m{428 kgf*cm, 31 ft.*lbf}
Tighten the bolt.
- Torque:
- 15 N*m{153 kgf*cm, 11 ft.*lbf}
| 28. INSTALL REAR CENTER SEAT HEADREST ASSEMBLY (w/ Center Armrest) |
| 29. INSTALL REAR SEATBACK HEATER ASSEMBLY (w/ Seat Heater System) |
Set the rear seatback heater assembly onto the rear separate type seatback cover so that the name stamp is facing the rear seatback pad LH.
 |
Install the seatback heater with new tack pins.
| 30. INSTALL REAR SEPARATE TYPE SEATBACK COVER |
w/ Center Armrest:
Using hog ring pliers, install the seatback cover with new hog rings.- NOTICE:
- Be careful not to damage the cover.
- When installing the hog rings, avoid wrinkling the cover.
 |
w/o Center Armrest:
Using hog ring pliers, install the seatback cover with new hog rings.- NOTICE:
- Be careful not to damage the cover.
- When installing the hog rings, avoid wrinkling the cover.
 |
w/ Rear Seat Side Airbag:
Connect the seatback cover bracket to the seatback pad.
 |
| 31. INSTALL SEATBACK COVER WITH PAD |
Install the seatback cover with pad.
w/ Center Armrest:
Pull out the seat belt.
 |
w/o Center Armrest:
Pull out the seat belt.
 |
w/ Rear Seat Side Airbag:
Pass the side airbag wire harness through the hole in the seatback.
w/ Seat Heater System:
Pass the seatback heater wire harness through the hole in the seatback.
Connect the seatback heater wire harness and install a new cable tie.
w/ Rear Seat Side Airbag:
Install the seatback cover bracket to the seat frame with the cap nut.- Torque:
- 5.5 N*m{56 kgf*cm, 49 in.*lbf}
- NOTICE:
- After the seatback trim cover is assembled, make sure the side airbag strap is not twisted.
 |
w/ Center Armrest:
Using hog ring pliers, install new hog rings to the seatback frame.
 |
w/o Center Armrest:
Using hog ring pliers, install new hog rings to the seatback frame.
 |
| 32. INSTALL REAR SEAT BELT HOLE COVER LH |
 |
Attach the 4 claws to install the cover.
Install the screw.
| 33. INSTALL SHOULDER BELT ANCHOR COVER |
 |
Attach the 2 claws to install the cover.
| 34. INSTALL REAR NO. 1 SEAT HEADREST SUPPORT ASSEMBLY |
w/ Center Armrest:
Attach the 4 claws to install the 2 supports.
 |
w/o Center Armrest:
Attach the 8 claws to install the 4 supports.
 |
| 35. INSTALL REAR SEAT HEADREST ASSEMBLY |
| 36. INSTALL REAR SEATBACK BOARD SUB-ASSEMBLY LH |
w/ Center Armrest:
Push the board down to attach the 2 claws on the bottom.
Attach the 2 claws on the top of the board to install it.
 |
w/o Center Armrest:
Push the board down to attach the 3 claws on the bottom.
Attach the 3 claws on the top of the board to install it.
 |
| 37. INSTALL REAR SEATBACK COVER |
 |
Attach the 4 claws to install the cover.
| 38. INSTALL REAR SEAT CUSHION HEATER ASSEMBLY (w/ Seat Heater System) |
Set the rear seat cushion heater assembly onto the rear separate type seat cushion cover so that the name stamp is facing the rear seat cushion pad LH.
 |
Install the seat cushion heater with new tack pins.
| 39. INSTALL REAR SEPARATE TYPE SEAT CUSHION COVER |
 |
Using hog ring pliers, install the seat cushion cover to the seat cushion pad with new hog rings.
- NOTICE:
- Be careful not to damage the cover.
- When installing the hog rings, avoid wrinkling the cover.
Attach the 3 pieces of fastening tape.
 |
| 40. INSTALL SEAT CUSHION COVER WITH PAD |
Install the seat cushion cover with pad.
w/ Rear Seat Side Airbag:
Pass the side airbag wire harness through the hole in the seat cushion.
w/ Seat Heater System:
Pass the seatback heater wire harness through the hole in the seat cushion.
Connect the 2 seat heater connectors.
w/ Rear Seat Side Airbag:
Attach the side airbag wire harness clamps.
| 41. CONNECT NO. 1 SEAT 3 POINT TYPE BELT ASSEMBLY LH |
 |
Connect the belt anchor.
- NOTICE:
- Do not overlap the anchor part of the seat belt and protruding parts of the vehicle body.
| 42. INSTALL REAR NO. 1 SEAT INNER BELT ASSEMBLY LH |
 |
Install the belt with the bolt.
- Torque:
- 42 N*m{428 kgf*cm, 31 ft.*lbf}
- NOTICE:
- Do not overlap the anchor part of the seat belt and protruding parts of the vehicle body.
- HINT:
- The No. 1 seat 3 point type belt anchor is fixed with the same bolt as the rear No. 1 seat inner belt LH. Therefore, connect it when installing the rear No. 1 seat inner belt LH.
| 43. INSTALL FOLD SEAT LOCK CONTROL CABLE SUB-ASSEMBLY |
| 44. INSTALL REAR SEAT TRACK HANDLE SUB-ASSEMBLY |
Attach the cable clamp to connect the cable.
 |
Attach the 2 cable clamps to connect the 2 cables.
 |
Install the seat track handle with the 2 screws.
 |
| 45. INSTALL REAR SEAT UNDER TRAY COVER LH |
 |
Attach the 4 claws to install the cover.
Install the 2 screws.
| 46. INSTALL REAR SEAT CUSHION COVER RH |
 |
Attach the 2 claws to install the cover.
Install the 4 screws.
| 47. INSTALL NO. 1 SEAT CUSHION PLATE |
 |
Attach the 3 claws to install the seat cushion plate.
| 48. INSTALL REAR UNDER SIDE COVER LH |
 |
Attach the 2 claws and 2 clips to install the cover.
Install the 5 screws.
Attach the 10 claws.
 |
| 49. INSTALL REAR SEATBACK STAY COVER LH |
 |
Attach the 2 claws to install the cover.
Install the screw.
| 50. INSTALL SEAT BELT ANCHOR COVER CAP |
Install the anchor cover cap with the screw.
 |
Attach the claw to close the cap.
 |
| 51. INSTALL REAR NO. 1 SEAT HINGE SUB-ASSEMBLY RH |
 |
Install the hinge with the 2 nuts.
- Torque:
- 42 N*m{428 kgf*cm, 31 ft.*lbf}
| 52. INSTALL REAR NO. 1 SEAT HINGE SUB-ASSEMBLY LH |
Attach the cable clamp to connect the cable.
 |
Install the hinge with the 2 nuts.
- Torque:
- 42 N*m{428 kgf*cm, 31 ft.*lbf}
 |
w/ Rear Seat Side Airbag:
Attach the wire harness clamp.
w/ Seat Heater System:
Attach the wire harness clamp.
| 53. INSTALL REAR NO. 2 SEAT PROTECTOR |
Install the wire harness, and attach 2 claws to close the protector.
Attach the claw to install the protector to the seat hinge.
 |
Install the clip.
w/ Rear Seat Side Airbag:
Attach the claw to install the wire harness connector.
 |
w/ Seat Heater System:
Attach the claw to install the wire harness connector.
| 54. INSTALL REAR SEAT SIDE HINGE MALE COVER RH |
Attach the clip to install the cover.
 |
| 55. INSTALL REAR SEAT SIDE HINGE MALE COVER LH |
Attach the clip to install the cover.
| 56. INSTALL REAR SEAT SIDE HINGE FEMALE COVER |
Attach the 6 claws to install the 2 covers.
 |
| 57. INSTALL FOLD SEAT STOPPER BAND ASSEMBLY |
Install the fold seat stopper band to the seat leg side cover.
| 58. INSTALL REAR NO. 2 SEAT LEG SIDE COVER |
Pass the fold seat stopper band through the seat leg side cover and attach it to the seat cushion frame with the bolt.
 |
Attach the 4 claws to install the seat leg side cover.
 |
Install the 4 screws.
| 59. INSTALL NO. 1 SEAT CUSHION COVER |
 |
Attach the 4 claws to install the 2 covers.
| 60. INSTALL UPPER SEAT TRACK RAIL COVER RH |
 |
Attach the 2 claws to install the cover.
| 61. INSTALL UPPER SEAT TRACK RAIL COVER LH |
 |
Attach the 2 claws to install the cover.
| 62. INSTALL REAR NO. 1 SEAT RECLINING COVER RH |
 |
Attach the 4 claws to install the cover.
Install the 2 screws.
| 63. INSTALL REAR NO. 1 SEAT RECLINING COVER LH |
 |
Attach the 3 claws in the order shown in the illustration to install the cover.
Install the 2 screws.
| 64. INSTALL RECLINING ADJUSTER RELEASE HANDLE LH |
 |
Install the release handle with the screw.
| 65. INSTALL SEAT ADJUSTER BOLT COVER |
 |
Attach the 2 claws to install the cover.