Power Mirror Control System (W/ Retract Mirror) Data List / Active Test

Vehicle Exterior. Land Cruiser. Urj200, 202 Grj200 Vdj200
Mirror (Ext). Land Cruiser. Urj200, 202 Grj200 Vdj200

  1. READ DATA LIST

  1. PERFORM ACTIVE TEST

Power Mirror Control System (W/ Retract Mirror) -- Data List / Active Test



READ DATA LIST
HINT:
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

  1. Connect the GTS to the DLC3.

  2. Turn the engine switch on (IG).

  3. Turn the GTS on.

  4. Enter the following menus: Body Electrical / (desired system) / Data List.

  5. According to the display on the GTS, read the Data List.

    Main Body
    Tester Display
    		Measurement Item/Range
    		Normal Condition
    		Diagnostic Note
    Mirror Selection SW (R)
    		Mirror select switch signal for RH mirror / ON or OFF
    		ON: Mirror select switch is R position
    OFF: Mirror select switch is except R position
    		-
    Mirror Selection SW (L)
    		Mirror select switch signal for LH mirror / ON or OFF
    		ON: Mirror select switch is L position
    OFF: Mirror select switch is except L position
    		-
    Mirror Position SW (R)
    		Mirror surface adjust switch signal (Right) / ON or OFF
    		ON: Right switch on
    OFF: Any switch except right on or all switches off
    		-
    Mirror Position SW (L)
    		Mirror surface adjust switch signal (Left) / ON or OFF
    		ON: Left switch on
    OFF: Any switch except left on or all switches off
    		-
    Mirror Position SW (Up)
    		Mirror surface adjust switch signal (Up) / ON or OFF
    		ON: Up switch on
    OFF: Any switch except up on or all switches off
    		-
    Mirror Position SW (Dwn)
    		Mirror surface adjust switch signal (Down) / ON or OFF
    		ON: Down switch on
    OFF: Any switch except down on or all switches off
    		-
    Outer Mirror Fold SW
    		Mirror retract switch signal / ON or OFF
    		ON: Mirror retract switch on (retracting)
    OFF: Mirror retract switch off
    		-
    Reverse Coupled Actuation Mirror Angle
    		Revers shift-linked mirror position memorization function setting / Default Setting or User Setting
    		Customized value displayed
    		-
    Mem SW NO. w/KeyID1
    		Switch linked with key ID1 / NONE, MEM, SW1, MEM SW2 or MEM SW3
    		NONE: No switches linked with key ID1
    MEM SW1: M1 linked with key ID1
    MEM SW2: M2 linked with key ID1
    MEM SW3: M3 linked with key ID1
    		-
    Mem SW NO. w/KeyID2
    		Switch linked with key ID2 / NONE, MEM, SW1, MEM SW2 or MEM SW3
    		NONE: No switches linked with key ID2
    MEM SW1: M1 linked with key ID2
    MEM SW2: M2 linked with key ID2
    MEM SW3: M3 linked with key ID2
    		-
    Mem SW NO. w/KeyID3
    		Switch linked with key ID3 / NONE, MEM, SW1, MEM SW2 or MEM SW3
    		NONE: No switches linked with key ID3
    MEM SW1: M1 linked with key ID3
    MEM SW2: M2 linked with key ID3
    MEM SW3: M3 linked with key ID3
    		-
    Mem SW NO. w/KeyID4
    		Switch linked with key ID4 / NONE, MEM, SW1, MEM SW2 or MEM SW3
    		NONE: No switches linked with key ID4
    MEM SW1: M1 linked with key ID4
    MEM SW2: M2 linked with key ID4
    MEM SW3: M3 linked with key ID4
    		-
    Mem SW NO. w/KeyID5
    		Switch linked with key ID5 / NONE, MEM, SW1, MEM SW2 or MEM SW3
    		NONE: No switches linked with key ID5
    MEM SW1: M1 linked with key ID5
    MEM SW2: M2 linked with key ID5
    MEM SW3: M3 linked with key ID5
    		-
    Mem SW NO. w/KeyID6
    		Switch linked with key ID6 / NONE, MEM, SW1, MEM SW2 or MEM SW3
    		NONE: No switches linked with key ID6
    MEM SW1: M1 linked with key ID6
    MEM SW2: M2 linked with key ID6
    MEM SW3: M3 linked with key ID6
    		-
    Mem SW NO. w/KeyID7
    		Switch linked with key ID7 / NONE, MEM, SW1, MEM SW2 or MEM SW3
    		NONE: No switches linked with key ID7
    MEM SW1: M1 linked with key ID7
    MEM SW2: M2 linked with key ID7
    MEM SW3: M3 linked with key ID7
    		-

    Mirror L
    Tester Display
    		Measurement Item/Range
    		Normal Condition
    		Diagnostic Note
    Seat Memory Switch1
    		Seat memory switch M1 switch signal / ON or OFF
    		ON: Seat memory switch M1 switch on
    OFF: Seat memory switch M1 switch off
    		-
    Seat Memory Switch2
    		Seat memory switch M2 switch signal / ON or OFF
    		ON: Seat memory switch M2 switch on
    OFF: Seat memory switch M2 switch off
    		-
    Seat Memory Switch3
    		Seat memory switch M3 switch signal / ON or OFF
    		ON: Seat memory switch M3 switch on
    OFF: Seat memory switch M3 switch off
    		-
    Seat Memory Set SW
    		Seat memory switch SET switch signal / ON or OFF
    		ON: Seat memory switch SET switch on
    OFF: Seat memory switch SET switch off
    		-
    Mirror Memory No.1
    		Mirror position memorized in seat memory switch 1 / ON or OFF
    		ON: Memorized
    OFF: Not memorized
    		-
    Mirror Memory No.2
    		Mirror position memorized in seat memory switch 2 / ON or OFF
    		ON: Memorized
    OFF: Not memorized
    		-
    Mirror Memory No.3
    		Mirror position memorized in seat memory switch 3 / ON or OFF
    		ON: Memorized
    OFF: Not memorized
    		-
    Mirror Memory No.4
    		Mirror position memorized in seat memory switch 4 / ON or OFF
    		ON: Memorized
    OFF: Not memorized
    		Only item displayed (not supported)
    Mirror Memory No.5
    		Mirror position memorized in seat memory switch 5 / ON or OFF
    		ON: Memorized
    OFF: Not memorized
    		Only item displayed (not supported)
    Mirror Memory No.6
    		Mirror position memorized in seat memory switch 6 / ON or OFF
    		ON: Memorized
    OFF: Not memorized
    		Only item displayed (not supported)
    Mirror Memory (Rev) No.1
    		Reverse shift-linked mirror position memorized in seat memory switch 1 / ON or OFF
    		ON: Memorized
    OFF: Not memorized
    		-
    Mirror Memory (Rev) No.2
    		Reverse shift-linked mirror position memorized in seat memory switch 2 / ON or OFF
    		ON: Memorized
    OFF: Not memorized
    		-
    Mirror Memory (Rev) No.3
    		Reverse shift-linked mirror position memorized in seat memory switch 3 / ON or OFF
    		ON: Memorized
    OFF: Not memorized
    		-
    Mirror Vertical Sensor Vol
    		Vertical mirror position / 0 to 5 V
    		Within range from 0 to 5 V
    		-
    Mirror Horizontal Sensor Vol
    		Horizontal mirror position / 0 to 5 V
    		Within range from 0 to 5 V
    		-
    Mirror Fold Detect
    		Condition of retractable outer mirror / Error or Normal
    		Error: Retractable outer mirror is malfunctioning
    Normal: Retractable outer mirror is normal
    		Only item displayed (not supported)
    +B Voltage Input Value
    		Power supply for outer mirror control ECU assembly / 0 to 25.5 V
    		0 to 25.5 (V)
    		-
    # Codes
    		Number of trouble codes / 0 to 255
    		Number of stored DTCs displayed
    		-

    Mirror R
    Tester Display
    		Measurement Item/Range
    		Normal Condition
    		Diagnostic Note
    Seat Memory Switch1
    		Seat memory switch M1 switch signal / ON or OFF
    		ON: Seat memory switch M1 switch on
    OFF: Seat memory switch M1 switch off
    		Only item displayed (not supported)
    Seat Memory Switch2
    		Seat memory switch M2 switch signal / ON or OFF
    		ON: Seat memory switch M2 switch on
    OFF: Seat memory switch M2 switch off
    		Only item displayed (not supported)
    Seat Memory Switch3
    		Seat memory switch M3 switch signal / ON or OFF
    		ON: Seat memory switch M3 switch on
    OFF: Seat memory switch M3 switch off
    		Only item displayed (not supported)
    Seat Memory Set SW
    		Seat memory switch SET switch signal / ON or OFF
    		ON: Seat memory switch SET switch on
    OFF: Seat memory switch SET switch off
    		Only item displayed (not supported)
    Mirror Memory No.1
    		Mirror position memorized in seat memory switch 1 / ON or OFF
    		ON: Memorized
    OFF: Not memorized
    		-
    Mirror Memory No.2
    		Mirror position memorized in seat memory switch 2 / ON or OFF
    		ON: Memorized
    OFF: Not memorized
    		-
    Mirror Memory No.3
    		Mirror position memorized in seat memory switch 3 / ON or OFF
    		ON: Memorized
    OFF: Not memorized
    		-
    Mirror Memory No.4
    		Mirror position memorized in seat memory switch 4 / ON or OFF
    		ON: Memorized
    OFF: Not memorized
    		Only item displayed (not supported)
    Mirror Memory No.5
    		Mirror position memorized in seat memory switch 5 / ON or OFF
    		ON: Memorized
    OFF: Not memorized
    		Only item displayed (not supported)
    Mirror Memory No.6
    		Mirror position memorized in seat memory switch 6 / ON or OFF
    		ON: Memorized
    OFF: Not memorized
    		Only item displayed (not supported)
    Mirror Memory (Rev) No.1
    		Reverse shift-linked mirror position memorized in seat memory switch 1 / ON or OFF
    		ON: Memorized
    OFF: Not memorized
    		-
    Mirror Memory (Rev) No.2
    		Reverse shift-linked mirror position memorized in seat memory switch 2 / ON or OFF
    		ON: Memorized
    OFF: Not memorized
    		-
    Mirror Memory (Rev) No.3
    		Reverse shift-linked mirror position memorized in seat memory switch 3 / ON or OFF
    		ON: Memorized
    OFF: Not memorized
    		-
    Mirror Vertical Sensor Vol
    		Vertical mirror position / 0 to 5 V
    		Within range from 0 to 5 V
    		-
    Mirror Horizontal Sensor Vol
    		Horizontal mirror position / 0 to 5 V
    		Within range from 0 to 5 V
    		-
    Mirror Fold Detect
    		Condition of retractable outer mirror / Error or Normal
    		Error: Retractable outer mirror is malfunctioning
    Normal: Retractable outer mirror is normal
    		Only item displayed (not supported)
    +B Voltage Input Value
    		Power supply for outer mirror control ECU assembly / 0 to 25.5 V
    		0 to 25.5 (V)
    		-
    # Codes
    		Number of trouble codes / 0 to 255
    		Number of stored DTCs displayed
    		-


PERFORM ACTIVE TEST
HINT:
Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

  1. Connect the GTS to the DLC3.

  2. Turn the engine switch on (IG).

  3. Turn the GTS on.

  4. Enter the following menus: Body Electrical / Mirror / Active Test.

  5. According to the display on the GTS, perform the Active Test.

    Mirror
    Tester Display
    		Test Part
    		Control Range
    		Diagnostic Note
    RH Mirror Up/Down
    		Mirror vertical operation
    		Up / OFF / Down
    		-
    RH Mirror Right/Left
    		Mirror horizontal operation
    		Right / OFF / Left
    		-
    LH Mirror Up/Down
    		Mirror vertical operation
    		Up / OFF / Down
    		-
    LH Mirror Right/Left
    		Mirror horizontal operation
    		Right / OFF / Left
    		-
    Mirror Fold
    		Mirror retract operation
    		ON / OFF
    		-
    Mirror Return
    		Mirror retract operation
    		ON / OFF
    		-