Lighting System Data List / Active Test

Vehicle Exterior. Land Cruiser. Urj200, 202 Grj200 Vdj200
Lighting (Ext). Land Cruiser. Urj200, 202 Grj200 Vdj200

  1. DATA LIST

  1. ACTIVE TEST

Lighting System -- Data List / Active Test



DATA LIST
HINT:
Using the intelligent tester to read the Data List allows values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

  1. Connect the intelligent tester to the DLC3.

  2. Turn the ignition switch to ON.

  3. Turn the intelligent tester on.

  4. Enter the following menus: Body / (desired system) / Data List.

  5. According to the display on the intelligent tester, read the Data List.

    Main Body
    Tester Display
    		Measurement Item/Range
    		Normal Condition
    		Diagnostic Note
    ACC SW
    		Ignition switch / ACC or OFF
    		ON: Ignition switch ACC
    OFF: Ignition switch off
    		"ON" is also displayed for this item when the ignition switch is ON.
    IG SW
    		Ignition switch / ON or OFF
    		ON: Ignition switch ON
    OFF: Ignition switch off
    		"OFF" is also displayed for this item when the ignition switch is ACC.
    Stop Light SW
    		Stop light switch / ON or OFF
    		ON: Brake pedal depressed
    OFF: Brake pedal released
    		-
    D Door Courtesy SW
    		Front door courtesy light switch LH signal / ON or OFF
    		ON: Front door courtesy light switch LH on
    OFF: Front door courtesy light switch LH off
    		-
    P Door Courtesy SW
    		Front door courtesy light switch RH signal / ON or OFF
    		ON: Front door courtesy light switch RH on
    OFF: Front door courtesy light switch RH off
    		-
    RR Door Courtesy SW
    		Rear door courtesy light switch RH signal / ON or OFF
    		ON: Rear door courtesy light switch RH on
    OFF: Rear door courtesy light switch RH off
    		-
    RL Door Courtesy SW
    		Rear door courtesy light switch LH signal / ON or OFF
    		ON: Rear door courtesy light switch LH on
    OFF: Rear door courtesy light switch LH off
    		-
    Back Door Courtesy SW
    		Back door courtesy light switch signal / ON or OFF
    		ON: Back door courtesy light switch on
    OFF: Back door courtesy light switch off
    		-
    Dimmer SW
    		Dimmer switch signal / ON or OFF
    		ON: Dimmer switch high
    OFF: Dimmer switch except high
    		-
    Passing Light SW
    		Passing light switch signal / ON or OFF
    		ON: Passing light switch on
    OFF: Passing light switch off
    		-
    Front Fog Light SW*1
    		Front fog light switch signal / ON or OFF
    		ON: Front fog light switch on
    OFF: Front fog light switch off
    		-
    Auto Light SW*2
    		Auto light switch signal / ON or OFF
    		ON: Auto light switch on
    OFF: Auto light switch off
    		-
    Head Light SW (Head)
    		Headlight switch signal / ON or OFF
    		ON: Light control switch head
    OFF: Light control switch except head
    		-
    Head Light SW (Tail)
    		Taillight switch signal / ON or OFF
    		ON: Light control switch tail
    OFF: Light control switch neither tail nor head
    		-
    Illumination Rate lnfo
    		Illumination rate / min.: 0, max.: 99.99
    		Actual illumination rate displayed
    		-
    I/L ON W/Door Key Unlock
    		Interior light ON with unlock / ON or OFF
    		Customize setting displayed.
    		-
    Lighting Time
    		Lighting Time / 7.5s or 15s or 30s
    		Customize setting displayed.
    		-
    I/L when ACC OFF
    		I/L ON/ACC OFF Light the I/L when ACC OFF / ON or OFF
    		Customize setting displayed.
    		-
    Light Control
    		Function which controls interior lights / ON or OFF
    		Customize setting displayed.
    		-
    Sensitivity
    		Turn on luminous intensity / DARK1, DARK2, NORMAL, LIGHT1, LIGHT2
    		Customize setting displayed.
    		-
    Disp Ex ON Sen
    		Display extinction luminous intensity / DARK1, DARK2, NORMAL, LIGHT1, LIGHT2
    		Customize setting displayed.
    		-
    Disp Ex OFF Sen
    		Display extinction release luminous intensity / DARK1, DARK2, NORMAL, LIGHT1, LIGHT2
    		Customize setting displayed.
    		-

    1. *1: w/ Front Fog Light
    2. *2: w/ Automatic Light Control System

    HL Auto Leveling (w/ Static Headlight Auto Leveling)
    Tester Display
    		Measurement Item/Range
    		Normal Condition
    		Diagnostic Note
    Headlight Low Beam State
    		Low beam headlight state / ON or OFF
    		ON: Low beam headlights on
    OFF: Low beam headlights off
    		-
    +B
    		Ignition power supply voltage value / 0 to 19.75 V
    		11 to 14 V
    		-
    Height Sens Pw Supply Val
    		Rear height control sensor power supply value / 0 to 5 V
    		Approximately 5 V
    		-
    Rr Height Sens Signal Val
    		Rear height control sensor signal value / 0 to 5 V
    		Approximately 2.5 V (When vehicle level)
    		The value changes according to the vehicle height.
    Vehicle Speed
    		Vehicle speed / 0 to 327.67 km/h
    		Actual vehicle speed
    		-
    Rear Height Adjust Valid Flag
    		Result of rear vehicle height calibration / Valid or Inval
    		Valid: Rear vehicle height calibration completed
    Inval: Rear vehicle height calibration not completed
    		-
    Init Writing Count
    		Number of times initialization performed / 0 to 255
    		Current condition displayed
    		-
    Sensor Initialization Hist
    		Sensor initialization history / not comp, 10%, 25%, 50%, 75%, 100% or complied
    		Current condition displayed
    		-
    Number Of Trouble Codes
    		Number of trouble codes / 0 to 255
    		Condition can be displayed
    		-

    AFS (w/ Dynamic Headlight Auto Leveling)
    Tester Display
    		Measurement Item/Range
    		Normal Condition
    		Diagnostic Note
    Headlight Low Beam State
    		Low beam headlight state / ON or OFF
    		ON: Low beam headlights on
    OFF: Low beam headlights off
    		-
    Headlight High Beam State
    		High beam headlight state / ON or OFF
    		ON: High beam headlights on
    OFF: High beam headlights off
    		-
    Engine
    		Engine condition / Run or Stop
    		Run: Engine running
    Stop: Engine stopped
    		-
    +B
    		Ignition power supply voltage value / 0 to 19.75 V
    		11 to 14 V
    		-
    Height Sens Pw Supply Val
    		Height control sensor power supply value / 0 to 6.25 V
    		4.7 to 5.2 V
    		-
    Fr Height Sens Signal Val*
    		Front height control sensor signal value / 0 to 5 V
    		Approximately 2.5 V (When vehicle level)
    		The value changes according to the vehicle height.
    Rr Height Sens Signal Val
    		Rear height control sensor signal value / 0 to 5 V
    		Approximately 2.5 V (When vehicle level)
    		The value changes according to the vehicle height.
    FR Wheel Speed
    		Front right wheel speed / 0 to 327.67 km/h
    		Condition can be displayed
    		-
    FL Wheel Speed
    		Front left wheel speed / 0 to 327.67 km/h
    		Condition can be displayed
    		-
    Vehicle Speed
    		Vehicle speed / 0 to 327.67 km/h
    		Condition can be displayed
    		-
    Rear Height Adjust Valid Flag
    		Rear height adjustment range / Valid or Inval
    		Condition can be displayed
    		-
    Init Writing Count
    		Number of times for initialization / 0 to 255
    		Condition can be displayed
    		-
    Sensor Initialization Hist
    		Sensor initialization history / not comp, 10%, 25%, 50%, 75%, 100% or complied
    		Condition can be displayed
    		-
    Number Of Trouble Codes
    		Number of trouble codes / 0 to 255
    		Condition can be displayed
    		-
    1. *: w/ Active Height Control Suspension

ACTIVE TEST
HINT:
Using the intelligent tester to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

  1. Connect the intelligent tester to the DLC3.

  2. Turn the Ignition switch to ON.

  3. Turn the intelligent tester on.

  4. Enter the following menus: Body / (desired system) / Active Test.

  5. According to the display on the intelligent tester, perform the Active Test.

    Main Body
    Tester Display
    		Test Part
    		Control Range
    		Diagnostic Note
    Hazard
    		Hazard warning signal
    		ON/OFF
    		-
    Illuminated Entry System
    		Illumination light
    		ON/OFF
    		-
    Indicator for Lighting
    		Illumination of switch indicator operation
    		ON/OFF
    		-
    Taillight Relay
    		Taillight
    		ON/OFF
    		-
    Headlight Relay
    		Headlight
    		ON/OFF
    		-
    Head Light Hi
    		Headlight (Hi)
    		ON/OFF
    		-
    Front Fog Light Relay*1
    		Front fog light
    		ON/OFF
    		-
    Rear Fog Light Relay*2
    		Rear fog light
    		ON/OFF
    		-
    Relay for Interior Light Auto Cut Function*3
    		DOME CUT relay
    		ON/OFF
    		Perform the Active test of the DOME CUT relay when the ignition switch is off
    Dimmer Signal
    		Illumination dimming operation
    		ON/OFF
    		-

    1. *1: w/ Front Fog Light
    2. *2: w/ Rear Fog Light
    3. *3: w/ Dome Cut Relay

    Body No. 4 (w/ Side Step Light)
    Tester Display
    		Test Part
    		Control Range
    		Diagnostic Note
    Rear Step Light
    		Step light operation
    		OFF/ON
    		-

    HL Auto Leveling (w/ Static Headlight Auto Leveling)
    Tester Display
    		Test Part
    		Control Range
    		Diagnostic Note
    Drive The Leveling Motor UP*
    		Headlight leveling motor upward operation
    		ON/OFF
    		ON: Move up
    OFF: Stop
    Drive The Leveling Motor DOWN*
    		Headlight leveling motor downward operation
    		ON/OFF
    		ON: Move down
    OFF: Stop
    1. *: Perform the Active Test with the engine running and vehicle stopped.

    AFS (w/ Dynamic Headlight Auto Leveling)
    Tester Display
    		Test Part
    		Control Range
    		Diagnostic Note
    Drive The Leveling Motor UP1
    		Headlight leveling motor upward operation
    		ON/OFF
    		ON: Move up
    OFF: Stop
    Drive The Leveling Motor DOWN*1
    		Headlight leveling motor downward operation
    		ON/OFF
    		ON: Move down
    OFF: Stop
    AFS OFF Indicator
    		Headlight beam level control system warning light
    		ON/OFF
    		-
    Automatic High Beam Operation*2
    		Automatic high beam system operation
    		ON/OFF
    		-
    1. *1: Perform the Active Test with the engine running and vehicle stopped.
    2. *2: w/ Automatic High Beam System