Power Window Regulator Motor (For Front Door) -- Installation |
- HINT:
- Use the same procedure for the RH and LH sides.
- The procedure listed below is for the LH side.
- A bolt without a torque specification is shown in the standard bolt chart (Click here).
| 1. INSTALL FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY |
Apply MP grease to the sliding and rotating areas of the regulator motor.
Using a T25 "TORX" driver, install the front power window regulator motor assembly with the 3 screws.
- Torque:
- 5.4 N*m{55 kgf*cm, 48 in.*lbf}
- HINT:
- A new front power window regulator motor assembly uses self-tapping screws to thread new installation holes when the self-tapping screws are inserted.
| 2. INSTALL FRONT DOOR WINDOW REGULATOR SUB-ASSEMBLY |
Loosen the temporary bolt.
Text in Illustration *a Temporary Bolt
 |
Remove the 5 bolts, and front door window regulator sub-assembly LH.
- HINT:
- Remove the front door window regulator sub-assembly LH through the service hole.
- NOTICE:
- Be careful when removing the bolts as the front door window regulator sub-assembly LH may fall and become damaged.
Remove the front door window regulator sub-assembly LH and the front power window regulator motor assembly LH as a unit.
Remove the temporary bolt from the front door window regulator sub-assembly LH.
| 3. INSTALL FRONT DOOR GLASS SUB-ASSEMBLY |
Driver Side:
Temporarily install the multiplex network master switch.
Passenger Side:
Temporarily install the power window regulator switch assembly.
Connect the cable to the negative (-) battery terminal.
Move the front door glass sub-assembly until the bolts appear in the service holes.
Disconnect the cable from the negative (-) battery terminal.
Remove the 2 bolts.
- NOTICE:
- Be careful when removing the bolts as the glass may fall and become damaged.
 |
Remove the front door glass sub-assembly in the direction indicated by the arrows in the illustration.
- HINT:
- Remove the front door glass sub-assembly upward.
- NOTICE:
- Be careful not to damage the glass.
 |
Driver Side:
Remove the multiplex network master switch.
Passenger Side:
Remove the power window regulator switch assembly.
| 4. INSTALL FRONT DOOR SERVICE HOLE COVER |
Using a clip remover, detach the 9 clamps.
 |
Remove the bolt and disconnect the 2 connectors.
Remove the front door service hole cover LH.
- HINT:
- Remove the remaining tape on the door.
| 5. INSTALL FRONT NO. 1 SPEAKER ASSEMBLY |
Connect the speaker connector.
 |
Install the speaker with the 4 screws.
- NOTICE:
- Do not touch the cone part of the speaker.
| 6. INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY |
Connect the connector.
 |
Connect the front door lock remote control cable assembly LH and front door inside locking cable assembly LH to the front door inside handle sub-assembly LH.
Attach the 4 claws and 13 clips to install the front door trim board sub-assembly LH.
 |
Install the 3 screws.
| 7. INSTALL DOOR ASSIST GRIP COVER |
Attach the 8 claws to install the door assist grip cover LH to the front door trim board sub-assembly LH.
| 8. INSTALL FRONT DOOR ARMREST BASE PANEL ASSEMBLY |
 |
Using a moulding remover, detach the 5 claws.
Disconnect the connector and remove the armrest base panel.
| 9. INSTALL FRONT DOOR INSIDE HANDLE BEZEL |
Attach the 4 claws to install the front door inside handle bezel LH.
 |
| 10. INSTALL FRONT LOWER DOOR FRAME BRACKET GARNISH |
Attach the clip and claw, and install the front door lower frame bracket garnish LH.
| 11. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
- NOTICE:
- When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).