Spiral Cable Inspection

Vehicle Interior. Land Cruiser. Urj200, 202 Grj200 Vdj200
Supplemental Restraint Systems. Land Cruiser. Urj200, 202 Grj200 Vdj200

  1. INSPECT SPIRAL CABLE

Spiral Cable -- Inspection



1. INSPECT SPIRAL CABLE

  1. If there are any defects as mentioned below, replace the spiral cable with a new one:
    Scratches, cracks, dents or chips on the connector or the spiral cable.



    Land Cruiser. Urj200, 202 Grj200 Vdj200.Supplemental Restraint Systems.Airbag System.Spiral Cable Inspection

  1. Check the spiral cable.

    1. Set the spiral cable to the center position (Click here).

    2. Measure the resistance between each terminal of the spiral cable according to the table below.

    3. After setting the spiral cable to the center position, rotate the spiral cable 2.5 times clockwise, and measure the resistance as shown. Then rotate the spiral cable 5 times counterclockwise, and measure the resistance as shown.

      Standard Resistance:
      Tester Connection
      		Condition
      		Specified Condition
      E13-1 - B2
      		Always
      		Below 1 Ω
      E13-2 - B1
      		Always
      		Below 1 Ω
      E13-3 - A1
      		Always
      		Below 1 Ω
      E13-4 - A2
      		Always
      		Below 1 Ω
      E12-6 - z36-10
      		Always
      		Below 1 Ω
      E12-5 - z36-9
      		Always
      		Below 1 Ω
      E12-4 - z36-8
      		Always
      		Below 1 Ω
      E12-3 - z36-7
      		Always
      		Below 1 Ω
      E12-2 - z36-6
      		Always
      		Below 1 Ω
      E12-2 - z37-4
      		Always
      		Below 1 Ω
      E12-1 - z37-3
      		Always
      		Below 1 Ω
      E12-12 - z36-5
      		Always
      		Below 1 Ω
      E12-11 - z36-4
      		Always
      		Below 1 Ω
      E12-10 - z36-3
      		Always
      		Below 1 Ω
      E12-9 - z36-2
      		Always
      		Below 1 Ω
      E12-8 - z36-1
      		Always
      		Below 1 Ω
      E12-8 - z37-2
      		Always
      		Below 1 Ω
      E12-7 - z37-1
      		Always
      		Below 1 Ω

    4. After setting the spiral cable to the center position, rotate the spiral cable 2.5 times clockwise. Then while rotating the spiral cable 5 times counterclockwise, measure the resistance as shown.

      Standard Resistance:
      Tester Connection
      		Condition
      		Specified Condition
      E13-1 - B2
      		Always
      		Below 1 Ω
      E13-2 - B1
      		Always
      		Below 1 Ω
      E13-3 - A1
      		Always
      		Below 1 Ω
      E13-4 - A2
      		Always
      		Below 1 Ω
      E12-6 - z36-10
      		Always
      		Below 1 Ω
      E12-5 - z36-9
      		Always
      		Below 1 Ω
      E12-4 - z36-8
      		Always
      		Below 1 Ω
      E12-3 - z36-7
      		Always
      		Below 1 Ω
      E12-2 - z36-6
      		Always
      		Below 1 Ω
      E12-2 - z37-4
      		Always
      		Below 1 Ω
      E12-1 - z37-3
      		Always
      		Below 1 Ω
      E12-12 - z36-5
      		Always
      		Below 1 Ω
      E12-11 - z36-4
      		Always
      		Below 1 Ω
      E12-10 - z36-3
      		Always
      		Below 1 Ω
      E12-9 - z36-2
      		Always
      		Below 1 Ω
      E12-8 - z36-1
      		Always
      		Below 1 Ω
      E12-8 - z37-2
      		Always
      		Below 1 Ω
      E12-7 - z37-1
      		Always
      		Below 1 Ω
      NOTICE:
      As the spiral cable may break, do not rotate the spiral cable more than the specified amount.