Dtc P0299 Turbocharger / Supercharger Underboost

Engine Hybrid System. Land Cruiser. Urj200, 202 Grj200 Vdj200
1Vd-Ftv Engine Control. Land Cruiser. Urj200, 202 Grj200 Vdj200

DESCRIPTION

INSPECTION PROCEDURE

CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0299)

CHECK INTAKE AND EXHAUST SYSTEM

INSPECT TURBOCHARGER SUB-ASSEMBLY (for Bank 1 or Bank 2)

CHECK CONNECTION OF VACUUM HOSE

READ VALUE USING INTELLIGENT TESTER (MAP)

READ VALUE USING INTELLIGENT TESTER (ACTUAL THROTTLE POSITION)

READ VALUE USING INTELLIGENT TESTER (ACTUAL EGR VALVE POS.)

READ VALUE USING INTELLIGENT TESTER (INJECTION FEEDBACK VAL #1 TO #8)

CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED

DTC P0299 Turbocharger / Supercharger Underboost


DESCRIPTION

HINT:
Refer to DTC P0046 (Click here).
Refer to DTC P00AF (Click here).

P0299
DTC Detection Drive Pattern
DTC Detection Condition
Trouble Area
Accelerate vehicle with accelerator halfway open or more starting from a speed of 120 km/h (192 mph) or more for 2 minutes (make sure gear is fixed and does not change)
The pressure is 55 kPa below the Target Boost Pressure for 40 seconds at an engine speed of 2800 to 4400 rpm (2 trip detection logic).
  1. Turbocharger sub-assembly
  2. Turbo motor driver
  3. Turbo motor driver power source
  4. Extremely low battery voltage (P0560 output simultaneously)
  5. Disconnected pipe between turbo and intake manifold
  6. Disconnected MAP sensor hose
  7. Throttle valve stuck closed
  8. EGR does not close
  9. Exhaust system or intake system modified (leading to increased pressure loss, etc.)
  10. Manifold absolute pressure sensor
  11. Injection system (reduction in fuel injection volume)
  12. ECM

Related Data List
DTC No.
Data List
P0299
  1. Target Booster Pressure
  2. MAP
HINT:
If DTC P0299 is stored, the following symptoms may appear:
  1. Variable nozzle stuck open malfunction
    1. Lack of power
    2. Vehicle surge or hesitation under light or medium load
    3. White smoke

INSPECTION PROCEDURE

HINT:
Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
NOTICE:
After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).
HINT:
Comparison of the Data List items MAP and Target Booster Pressure during acceleration under medium to high engine speeds can be used to determine the state of the problem.
1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0299)

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester on.

  1. Enter the following menus: Powertrain / Engine / DTC.

  1. Read the DTCs.

    Result:

    Display (DTC Output)
    		Proceed to
    P0299 is output
    		A
    P0299 and other DTCs are output
    		B


B
GO TO DTC CHART (Click here)
A


2.CHECK INTAKE AND EXHAUST SYSTEM

  1. Check the intake and exhaust system modifications.

    OK:
    No modifications.


NG
REPAIR OR REPLACE INTAKE AND EXHAUST SYSTEM
OK


3.INSPECT TURBOCHARGER SUB-ASSEMBLY (for Bank 1 or Bank 2)

  1. Check the turbocharger sub-assembly (for Bank 1 or Bank 2) (Click here).

    HINT:
    Check if the VN is stuck, if there are abnormal noises from the turbo (impeller is damaged), if there is turbo shaft rattle, and if the turbo shaft rotates smoothly.


NG
REPLACE TURBOCHARGER SUB-ASSEMBLY (for Bank 1 or Bank 2) (Click here)
OK


4.CHECK CONNECTION OF VACUUM HOSE

  1. Check the vacuum hoses of manifold absolute pressure sensor connections.



NG
REPAIR OR REPLACE VACUUM HOSE
OK


5.READ VALUE USING INTELLIGENT TESTER (MAP)

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester on.

  1. Enter the following menus: Powertrain / Engine / Data List / MAP.

  1. Read the value.

    Standard Value:

    Condition
    		Standard Value
    Idling
    		90 to 102 kPa
    3000 rpm
    		100 to 150 kPa


NG
REPLACE MANIFOLD ABSOLUTE PRESSURE SENSOR
OK


6.READ VALUE USING INTELLIGENT TESTER (ACTUAL THROTTLE POSITION)

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester on.

  1. Enter the following menus: Powertrain / Engine / Data List / Actual Throttle Position, Actual Throttle Position #2.

  1. Read the value.

    Standard Value:

    Condition
    		Standard Value
    Ignition switch ON
    		-5 to 5%
    Idling
    		0 to 90%


NG
REPLACE DIESEL THROTTLE BODY ASSEMBLY (for Bank 1 or Bank 2)
OK


7.READ VALUE USING INTELLIGENT TESTER (ACTUAL EGR VALVE POS.)
HINT:
For vehicles without EGR valve, perform troubleshooting from the next step.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester on.

  1. Enter the following menus: Powertrain / Engine / Active Test / Control the EGR Step Position or Control the EGR Step Position #2 / Data List / Actual EGR Valve Pos. or Actual EGR Valve Pos. #2.

  1. When changing the Active Test value from 0 to 100%, check that Actual EGR Valve Pos. or Actual EGR Valve Pos. #2 smoothly changes to the set opening angle.

    Standard Value:
    Value smoothly changes to within +/-10% of set opening angle.
    HINT:
    1. EGR valve closed: Actual EGR Valve Pos. is 0%.
    2. EGR valve open: Actual EGR Valve Pos. is 94.9%.

  1. Next, after the engine is warmed up, stop the engine and wait for 15 seconds. After that, start the engine again and idle it for 30 seconds. Then stop the engine and wait for 15 seconds. After starting the engine again, read the Data List values while idling.

    Standard Value:

    Tester Display
    		Standard Value
    EGR Close Learn Val.
    		3.5 to 4.5 V
    EGR Close Lrn. Val. #2
    		3.5 to 4.5 V
    EGR Close Lrn. Status
    		ON


NG
REPLACE EGR VALVE ASSEMBLY (No. 1 or No. 2)
OK


8.READ VALUE USING INTELLIGENT TESTER (INJECTION FEEDBACK VAL #1 TO #8)

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester on.

  1. Start the engine and warm it up.

  1. Enter the following menus: Powertrain / Engine / Data List / Injection Feedback Val #1 to #8.

  1. Read the values.

    Standard Value:

    Item
    		Engine Speed*
    		Reference Value
    Injection Feedback Val #1 to #8
    		Idling
    		-3.0 to 3.0 mm3/st
    HINT:
    1. *: The A/C switch and all accessory switches should be OFF, and the engine should be fully warmed up.
    2. When the values are outside the standard range, deposits inside the fuel injector may be causing the problem.
      OK:
      Values are within the standard range.


NG
REPLACE FUEL INJECTOR OF MALFUNCTIONING CYLINDER
OK


9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED

  1. Connect the intelligent tester to the DLC3.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Start the engine and warm it up.

  1. Accelerate the vehicle with the accelerator halfway open or more starting from a speed of 120 km/h (192 mph) or more for 2 minutes (make sure the gear is fixed and does not change).

  1. Enter the following menus: Powertrain / Engine / DTC / Pending.

  1. Read the DTC.

    Result
    Display (DTC Output)
    		Proceed to
    No output
    		A
    P0299
    		B



B
REPLACE ECM (Click here)
A

CHECK FOR INTERMITTENT PROBLEMS (Click here)