REMOVE REAR NO. 1 SEAT ASSEMBLY (for 60/40 Split Seat Type 60 Side)
REMOVE REAR NO. 1 SEAT ASSEMBLY (for 60/40 Split Seat Type 40 Side)
REMOVE REAR SEAT COVER CAP (w/ Rear No. 2 Seat, except Face to Face Seat Type)
Fuel Lid Lock Control Cable Assembly (For Lhd) -- Removal |
| 1. PRECAUTION |
- NOTICE:
- After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).
| 2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL |
- CAUTION:
- Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
- NOTICE:
- When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).
| 3. REMOVE TONNEAU COVER ASSEMBLY (w/ Tonneau Cover) |
Remove the tonneau cover assembly.
| 4. REMOVE FRONT SEAT ASSEMBLY LH |
for Manual Seat:
(Click here)
for Power Seat:
(Click here)
| 5. REMOVE FRONT SEAT ASSEMBLY RH |
for Manual Seat:
(Click here)
for Power Seat:
(Click here)
for Bench Seat Type:
(Click here)
| 6. REMOVE REAR NO. 1 SEAT ASSEMBLY (for 60/40 Split Seat Type 60 Side) |
| 7. REMOVE REAR NO. 1 SEAT ASSEMBLY (for 60/40 Split Seat Type 40 Side) |
| 8. REMOVE REAR NO. 1 SEAT ASSEMBLY (for Bench Seat Type) |
| 9. REMOVE INSTRUMENT SIDE PANEL LH |
 |
Put protective tape around the instrument side panel LH.
Text in Illustration *a Protective Tape
Using a moulding remover A, detach the 6 claws and remove the instrument side panel LH.
| 10. REMOVE INSTRUMENT SIDE PANEL RH |
 |
Put protective tape around the instrument side panel RH.
Text in Illustration *a Protective Tape
Using a moulding remover A, detach the 6 claws and remove the instrument side panel RH.
w/ Airbag Cut Off Switch:
Disconnect the connector and remove the instrument side panel RH.
| 11. REMOVE FRONT DOOR SCUFF PLATE LH |
 |
Detach the 7 claws and 4 clips, and remove the front door scuff plate LH.
| 12. REMOVE FRONT DOOR SCUFF PLATE RH |
- HINT:
- Use the same procedures described for the LH side.
| 13. REMOVE COWL SIDE TRIM BOARD LH |
 |
Remove the cap nut.
Text in Illustration *a Cap Nut
Detach the 2 clips and remove the cowl side trim board LH.
| 14. REMOVE COWL SIDE TRIM BOARD RH |
 |
Remove the cap nut.
Text in Illustration *a Cap Nut
Detach the 2 clips and remove the cowl side trim board LH.
| 15. REMOVE REAR STEP COVER |
- HINT:
- Use the same procedure for both rear step covers.
Detach the 2 claws and remove the rear step cover.
 |
| 16. REMOVE REAR DOOR SCUFF PLATE LH |
 |
Remove the screw.
Detach the 3 claws and 4 clips, and remove the rear door scuff plate LH.
| 17. REMOVE REAR DOOR SCUFF PLATE RH |
- HINT:
- Use the same procedures described for the LH side.
| 18. REMOVE NO. 2 AIR DUCT PLUG |
Detach the 4 claws and remove the 2 plugs.
- HINT:
- Use the same procedures for both sides.
 |
| 19. REMOVE AIR HEATER GUIDE LH |
Remove the 2 screws and guide.
- HINT:
- Use the same procedures for both sides.
 |
| 20. REMOVE AIR DUCT PLUG |
Detach the 2 claws and remove the plug.
- HINT:
- Use the same procedures for both sides.
 |
| 21. REMOVE AIR DUCT GUIDE |
Remove the screw.
 |
Detach the claw and remove the guide.
- HINT:
- Use the same procedures for both sides.
| 22. REMOVE REAR NO. 1 SEAT PROTECTOR |
Detach the clip and 4 claws, and remove the protector.
- HINT:
- Use the same procedures to remove the protector on the other side.
 |
| 23. REMOVE REAR NO. 2 SEAT PROTECTOR |
Detach the clip and 4 claws, and remove the protector.
- HINT:
- Use the same procedures to remove the protector on the other side.
 |
| 24. REMOVE REAR CONSOLE BOX SUB-ASSEMBLY |
w/o Console Box Lid:
(Click here)
w/ Cool Box:
(Click here)
w/o Cool Box:
(Click here)
| 25. REMOVE FRONT FLOOR CARPET ASSEMBLY |
Detach the 2 clips and 8 claws.
Remove the carpet from the floor, open the back door and tail gate, and remove the carpet from the rear of the vehicle.
 |
| 26. REMOVE REAR FLOOR MAT REAR SUPPORT PLATE |
 |
Detach the 6 clips and remove the rear floor mat support plate.
| 27. REMOVE NO. 1 TONNEAU COVER HOLDER CAP (w/ Tonneau Cover) |
 |
- HINT:
- Use the same procedure for both No. 1 tonneau cover holder caps.
Detach the 2 claws and remove the No. 1 tonneau cover holder cap.
| 28. REMOVE REAR SEAT COVER CAP (w/ Rear No. 2 Seat, except Face to Face Seat Type) |
- HINT:
- Use the same procedure for both No. 1 luggage compartment trim hooks.
Using a screwdriver, detach the 3 claws and remove the rear seat cover cap.
- HINT:
- Tape the screwdriver tip before use.
Text in Illustration *a Protective Tape
 |
| 29. REMOVE FRONT QUARTER TRIM PANEL ASSEMBLY RH |
 |
- HINT:
- When removing the front quarter trim panel assembly RH, operate the reclining adjuster release handle and move the No. 1 rear seat to the position shown in the illustration.
Detach the 3 claws and remove the outer lap belt anchor cover.
 |
Remove the bolt and rear No. 1 seat belt anchor.
 |
w/ Rear No. 2 Seat, except Face to Face Seat Type:
Detach the 3 claws and remove the outer lap belt anchor cover.
Remove the bolt and rear No. 2 seat belt anchor.
 |
w/ Rear No. 2 Seat, except Face to Face Seat Type:
Remove the clip and bolt.
Detach the 16 clips and 2 claws.
w/o Rear Air Conditioning System:
Disconnect the rear seat lock control lever cable and then remove the front quarter trim panel assembly RH.w/ Rear Air Conditioning System:
Disconnect the thermistor connector and rear seat lock control lever cable, and then remove the front quarter trim panel assembly RH.
w/o Rear No. 2 Seat or w/ Rear No. 2 Seat, for Face to Face Seat Type:
Remove the clip.
Detach the 16 clips and 2 claws, and remove the front quarter trim panel assembly RH.
w/ Tonneau Cover:
Remove the screw and clip.
Detach the 16 clips and 2 claws, and remove the front quarter trim panel assembly RH.
| 30. REMOVE FUEL FILLER OPENING LID LOCK RETAINER |
 |
Turn the cable counterclockwise and remove the cable from the retainer.
Turn the lock retainer counterclockwise and remove the lock retainer.
 |
| 31. REMOVE FUEL LID LOCK OPEN LEVER SUB-ASSEMBLY |
Detach the 2 claws.
 |
Disconnect the fuel lid lock control cable and remove the fuel lid lock open lever.
| 32. REMOVE FUEL LID LOCK CONTROL CABLE SUB-ASSEMBLY |
Using a screwdriver, disconnect the clamps shown in the illustration.
- HINT:
- Tape the screwdriver tip before use.
Remove the lock control cable.