Vane Pump (For 1Ur-Fe) Removal

Steering. Land Cruiser. Urj200, 202 Grj200 Vdj200
Power Assist Systems. Land Cruiser. Urj200, 202 Grj200 Vdj200

  1. PRECAUTION

  2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

  3. REMOVE FRONT WHEEL RH

  4. REMOVE FRONT FENDER APRON TRIM PACKING A

  5. REMOVE V-BANK COVER SUB-ASSEMBLY

  6. REMOVE AIR CLEANER AND HOSE

  7. REMOVE FAN AND GENERATOR V BELT

  8. DRAIN POWER STEERING FLUID

  9. DISCONNECT POWER STEERING OIL PRESSURE SENSOR CONNECTOR

  10. DISCONNECT PRESSURE FEED TUBE

  11. DISCONNECT SUCTION HOSE

  12. REMOVE VANE PUMP ASSEMBLY

Vane Pump (For 1Ur-Fe) -- Removal



1. PRECAUTION
NOTICE:
After turning the engine switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).


2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


3. REMOVE FRONT WHEEL RH


4. REMOVE FRONT FENDER APRON TRIM PACKING A


    Land Cruiser. Urj200, 202 Grj200 Vdj200

  1. Remove the 3 bolts and 2 screws.

  1. Turn the clip indicated by the arrow in the illustration to remove the front fender splash shield sub-assembly RH.



5. REMOVE V-BANK COVER SUB-ASSEMBLY


    Land Cruiser. Urj200, 202 Grj200 Vdj200.Power Assist Systems.Power Steering System.Vane Pump (For 1Ur-Fe) Removal

  1. Raise the front of the V-bank cover to detach the 3 pins. Then remove the 2 V-bank cover hooks from the bracket, and remove the V-bank cover.

    Text in Illustration
    *1
    		Grommet
    *2
    		Pin
    *3
    		Hook
    *4
    		Bracket


6. REMOVE AIR CLEANER AND HOSE


    Land Cruiser. Urj200, 202 Grj200 Vdj200

  1. Disconnect the No. 2 PCV hose and No. 1 air hose.

  1. Disconnect the mass air flow meter connector and detach the clamp.

  1. Remove the 3 bolts and loosen the hose clamp, and then remove the air cleaner and hose.



7. REMOVE FAN AND GENERATOR V BELT


    Land Cruiser. Urj200, 202 Grj200 Vdj200.Power Assist Systems.Power Steering System.Vane Pump (For 1Ur-Fe) Removal

  1. While turning the belt tensioner counterclockwise, align the service hole for the belt tensioner and the belt tensioner fixing position, and then insert a bar with a diameter of 5 mm (0.197 in.) into the service hole to fix the belt tensioner in place.

    Text in Illustration
    *1
    		Bar
    *2
    		Service Hole
    *a
    		Turn
    HINT:
    The pulley bolt for the belt tensioner has a left-hand thread.

  1. Remove the fan and generator V belt.



8. DRAIN POWER STEERING FLUID


9. DISCONNECT POWER STEERING OIL PRESSURE SENSOR CONNECTOR


    Land Cruiser. Urj200, 202 Grj200 Vdj200

  1. Detach the wire harness clamp and disconnect the connector.



10. DISCONNECT PRESSURE FEED TUBE


    Land Cruiser. Urj200, 202 Grj200 Vdj200.Power Assist Systems.Power Steering System.Vane Pump (For 1Ur-Fe) Removal

  1. Remove the bolt and disconnect the pressure feed tube.

    Text in Illustration
    *1
    		Pressure Feed Tube

  1. Remove the gasket.



11. DISCONNECT SUCTION HOSE


    Land Cruiser. Urj200, 202 Grj200 Vdj200

  1. Slide the clip and disconnect the suction hose from the vane pump.



12. REMOVE VANE PUMP ASSEMBLY


    Land Cruiser. Urj200, 202 Grj200 Vdj200

  1. Remove the 2 bolts and vane pump.