Steering Lock System Data List / Active Test

Steering. Land Cruiser. Urj200, 202 Grj200 Vdj200
Steering Column. Land Cruiser. Urj200, 202 Grj200 Vdj200

  1. DATA LIST

Steering Lock System -- Data List / Active Test



DATA LIST
HINT:
Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

  1. Turn the engine switch off.

  2. Connect the intelligent tester to the DLC3.

  3. Turn the engine switch on (IG).

  4. Turn the intelligent tester on.

  5. Enter the following menus: Body / Entry&Start / Data List.

  6. According to the display on the intelligent tester, read the "Data List".

    Entry&Start
    Tester Display
    		Measurement Item/Range
    		Normal Condition
    		Diagnostic Note
    #Codes
    		Number of diagnostic trouble codes
    		-
    		-
    Sensor Value
    		Sensor malfunction/NG (Past) or OK
    		NG (Past): Sensor malfunction
    OK: No malfunction
    		-
    Power Supply Short
    		Short in ECU/NG (Past) or OK
    		NG (Past): Short in ECU
    OK: No malfunction
    		-
    Power Supply Open
    		Open in ECU/NG (Past) or OK
    		NG (Past): Open in ECU
    OK: No malfunction
    		-
    Motor Driver Short
    		Short in driver ECU/NG (Past) or OK
    		NG (Past): Short in driver ECU
    OK: No malfunction
    		-
    Motor Driver Open
    		Open in driver ECU/NG (Past) or OK
    		NG (Past): Open in driver ECU
    OK: No malfunction
    		-
    Lock/Unlock Receive
    		Steering lock command reception record/YES or NO
    		YES: Steering lock/unlock signal received
    NO: Steering lock/unlock signal not received
    		-
    Lock Bar Stuck Error
    		Lock bar stuck malfunction/NG (Past) or OK
    		NG (Past): Lock bar stuck malfunction
    OK: No malfunction
    		-
    Push Start Error
    		Push button start function malfunction/NG (Past) or OK
    		NG (Past): Malfunction in push button start
    OK: No malfunction
    		-
    IG2 Status
    		IG2 voltage/ON or OFF
    		ON: 11 to 14 V
    OFF: Below 1 V
    		-
    IG(Lin)
    		LIN bus start-up status/ON or OFF
    		ON: LIN bus started-up
    OFF: LIN bus not started-up
    		-
    S Code Check
    		S code match record/NG or OK
    		NG: S code not matched
    OK: S code matched
    		-
    L Code Check
    		L code match record/NG or OK
    		NG: L code not matched
    OK: L code matched
    		-
    Unlock Request Receive
    		Steering lock unlock command reception status/NG or OK
    		NG: Unlock request not received
    OK: Unlock request received
    		-
    Lock Request Receive
    		Steering lock lock command reception status/NG or OK
    		NG: Lock request not received
    OK: Lock request received
    		-
    S Code Check(Past)
    		S code match record/NG (Past) or OK
    		NG (Past): S code not matched
    OK: S code matched
    		-
    L Code Check(Past)
    		L code match record/NG (Past) or OK
    		NG (Past): L code not matched
    OK: L code matched
    		-
    Steering Lock
    		Steering lock condition/Set or Unset
    		Set: Steering lock set
    Unset: Steering lock not set
    		This status changes depending on the state of various sensors.
    Steering Unlock
    		Steering unlock condition/Set or Unset
    		Set: Steering unlock set
    Unset: Steering unlock not set
    		This status changes depending on the state of various sensors.