Dtc P0550 Power Steering Pressure Sensor Circuit Malfunction

Engine Hybrid System. Land Cruiser. Urj200, 202 Grj200 Vdj200
1Ur-Fe Engine Control. Land Cruiser. Urj200, 202 Grj200 Vdj200

DESCRIPTION

WIRING DIAGRAM

MONITOR DESCRIPTION

CONFIRMATION DRIVING PATTERN

INSPECTION PROCEDURE

CHECK HARNESS AND CONNECTOR (ECM - POWER STEERING OIL PRESSURE SWITCH)

REPLACE POWER STEERING OIL PRESSURE SWITCH

CONFIRM WHETHER DTC OUTPUT RECURS

DTC P0550 Power Steering Pressure Sensor Circuit Malfunction

DTC P0552 Power Steering Pressure Sensor Circuit Low Input

DTC P0553 Power Steering Pressure Sensor Circuit High Input


DESCRIPTION

The power steering oil pressure switch is turned on when a power steering wheel load is generated by turning the steering wheel. The ECM regulates the engine idling speed according to the voltage output of the sensor.

DTC No.
DTC Detection Condition
Trouble Area
P0550
Power steering oil pressure switch voltage is below 0.28 V, or higher than 4.9 V for 0.5 seconds while the engine is running (1 trip detection logic).
  1. Open or short in power steering oil pressure switch circuit
  2. Power steering oil pressure switch
  3. ECM
P0552
Power steering oil pressure switch voltage is below 0.28 V for 0.5 seconds while the engine is running (1 trip detection logic).
  1. Open or short in power steering oil pressure switch circuit
  2. Power steering oil pressure switch
  3. ECM
P0553
Power steering oil pressure switch voltage is higher than 4.9 V for 0.5 seconds while the engine is running (1 trip detection logic).
  1. Open or short in power steering oil pressure switch circuit
  2. Power steering oil pressure switch
  3. ECM

WIRING DIAGRAM


Land Cruiser. Urj200, 202 Grj200 Vdj200.1Ur-Fe Engine Control.Sfi System. Dtc P0550 Power Steering Pressure Sensor Circuit Malfunction


MONITOR DESCRIPTION

The ECM monitors the switch voltage and uses this value to regulate the engine idling speed. When the sensor output voltage deviates from the normal operating range, the ECM determines that there is a malfunction in the power steering oil pressure switch and stores a DTC.

CONFIRMATION DRIVING PATTERN

  1. Idle the engine for 5 seconds or more.

INSPECTION PROCEDURE

HINT:
  1. If other DTCs related to different systems that have terminal E2 as the ground terminal are stored simultaneously, there may be an open circuit between terminal E2 and body ground.
  2. Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.
  3. Refer to "Data List / Active Test" [Power Steering Signal] (Click here).
1.CHECK HARNESS AND CONNECTOR (ECM - POWER STEERING OIL PRESSURE SWITCH)

  1. Disconnect the ECM connector.

  1. Disconnect the power steering oil pressure switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    for RHD
    Tester Connection
    		Condition
    		Specified Condition
    C59-2 (PSP) - C46-72 (PSP)
    		Always
    		Below 1 Ω
    C59-1 (VC) - C46-67 (VCV1)
    		Always
    		Below 1 Ω
    C59-3 (E2) - C46-98 (E2)
    		Always
    		Below 1 Ω
    C59-2 (PSP) or C46-72 (PSP) - Body ground
    		Always
    		10 kΩ or higher
    C59-1 (VC) or C46-67 (VCV1) - Body ground
    		Always
    		10 kΩ or higher

    for LHD
    Tester Connection
    		Condition
    		Specified Condition
    C59-2 (PSP) - C45-72 (PSP)
    		Always
    		Below 1 Ω
    C59-1 (VC) - C45-67 (VCV1)
    		Always
    		Below 1 Ω
    C59-3 (E2) - C45-98 (E2)
    		Always
    		Below 1 Ω
    C59-2 (PSP) or C45-72 (PSP) - Body ground
    		Always
    		10 kΩ or higher
    C59-1 (VC) or C45-67 (VCV1) - Body ground
    		Always
    		10 kΩ or higher


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2.REPLACE POWER STEERING OIL PRESSURE SWITCH

  1. Replace the power steering oil pressure switch (Click here).


NEXT


3.CONFIRM WHETHER DTC OUTPUT RECURS

  1. Connect the GTS to the DLC3.

  1. Turn the engine switch on (IG).

  1. Turn the GTS on.

  1. Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.

  1. Read the DTCs.

    Result
    Result
    		Proceed to
    P0550, P0552 and/or P0553 is output
    		A
    No DTC is output
    		B


B
END
A

REPLACE ECM (Click here)