Vehicle Stability Control System Check For Intermittent Problems

Brake. Land Cruiser. Urj200, 202 Grj200 Vdj200
Brake Control Dynamic Control Systems. Land Cruiser. Urj200, 202 Grj200 Vdj200

  1. DESCRIPTION

Vehicle Stability Control System -- Check For Intermittent Problems



DESCRIPTION
HINT:
A momentary interruption (open circuit) in the connectors and/or wire harness between the sensors and ECUs can be detected through the ECU data monitor function of the GTS.

  1. Turn the ignition switch off.

  2. Connect the GTS to the DLC3.

  3. Turn the ignition switch to ON.

  4. Turn the GTS on.

  5. Enter the following menus: Chassis / ABS/VSC/TRC / Data List.

  6. Select areas where momentary interruptions should be monitored.

    HINT:
    1. A momentary interruption (open circuit) cannot be detected for 3 seconds after the ignition switch is turned to ON (initial check).
    2. If Error is displayed, check for continuity between the ECUs and the sensors or between ECUs.
    3. Error remains displayed on the GTS for 1 second after the harness signal changes from a momentary interruption (open circuit) to normal.

    ABS/VSC/TRC
    Tester Display
    		Measurement Item/Range
    		Normal Condition
    		Diagnostic Note
    FR Speed Open
    		Front speed sensor RH open circuit detection/
    Error or Normal
    		Normal
    		-
    FL Speed Open
    		Front speed sensor LH open circuit detection/
    Error or Normal
    		Normal
    		-
    RR Speed Open
    		Rear speed sensor RH open circuit detection/
    Error or Normal
    		Normal
    		-
    RL Speed Open
    		Rear speed sensor LH open circuit detection/
    Error or Normal
    		Normal
    		-
    EFI Communication Open
    		ECM communication open circuit detection/
    Error or Normal
    		Normal
    		-
    Yaw Rate Open
    		Yaw rate sensor open circuit detection/
    Error or Normal
    		Normal
    		-
    Deceleration Open
    		Acceleration sensor open circuit detection/
    Error or Normal
    		Normal
    		-
    Steering Open
    		Steering sensor open circuit detection/
    Error or Normal
    		Normal
    		-
    Master Cylinder Open
    		Master cylinder pressure sensor open circuit detection/
    Error or Normal
    		Normal
    		-
    IG Voltage Value Decreased
    		IG voltage value decreased detection/
    Error or Normal
    		Normal
    		-
    IG Voltage Value Increased
    		IG voltage value increased detection/
    Error or Normal
    		Normal
    		-
    FR Speed Sensor Voltage Open
    		Front speed sensor RH voltage open circuit detection/
    Error or Normal
    		Normal
    		-
    FL Speed Sensor Voltage Open
    		Front speed sensor LH voltage open circuit detection/
    Error or Normal
    		Normal
    		-
    RR Speed Sensor Voltage Open
    		Rear speed sensor RH voltage open circuit detection/
    Error or Normal
    		Normal
    		-
    RL Speed Sensor Voltage Open
    		Rear speed sensor LH voltage open circuit detection/
    Error or Normal
    		Normal
    		-
    M/C Pressure Sensor Noise
    		Master cylinder pressure sensor noise detection/
    Error or Normal
    		Normal
    		-
    Yaw Rate Sensor Voltage Open
    		Yaw rate sensor voltage open circuit detection/
    Error or Normal
    		Normal
    		-
    EFI Communication Invalid
    		ECM communication invalid detection/
    Error or Normal
    		Normal
    		-

  7. While observing the screen, gently jiggle the connectors or wire harnesses between the ECUs and sensors or between ECUs.

    OK:
    Normal display appears.
    NOTICE:
    The connector and/or wire harness has a momentary interruption (open circuit) if the display changes. Repair or replace the connectors and/or wire harnesses as one of them is faulty.