Anti-Lock Brake System Data List / Active Test

Brake. Land Cruiser. Urj200, 202 Grj200 Vdj200
Brake Control Dynamic Control Systems. Land Cruiser. Urj200, 202 Grj200 Vdj200

  1. DATA LIST

  1. ACTIVE TEST

Anti-Lock Brake System -- Data List / Active Test



DATA LIST
HINT:
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

  1. Warm up the engine.

  2. Turn the ignition switch off.

  3. Connect the GTS to the DLC3.

  4. Turn the ignition switch to ON.

  5. Turn the GTS on.

  6. Enter the following menus: Chassis / ABS/VSC/TRC / Data List.

  7. According to the display on the GTS, read the Data List.

    ABS/VSC/TRC
    Tester Display
    		Measurement Item/Range
    		Normal Condition
    		Diagnostic Note
    ABS Warning Light
    		ABS warning light/ ON or OFF
    		ON: Warning light on
    OFF: Warning light off
    		-
    Brake Warning Light
    		Brake warning light/ ON or OFF
    		ON: Warning light on
    OFF: Warning light off
    		-
    Buzzer
    		Buzzer/ ON or OFF
    		ON: Buzzer on
    OFF: Buzzer off
    		The combination meter has a built-in buzzer.
    Stop Light SW
    		Stop light switch/ ON or OFF
    		ON: Brake pedal depressed
    OFF: Brake pedal released
    		-
    Parking Brake SW
    		Parking brake switch/ ON or OFF
    		ON: Parking brake applied
    OFF: Parking brake released
    		-
    Reservoir Warning SW
    		Brake fluid level warning switch/ ON or OFF
    		OFF
    		-
    Main Idle SW
    		Main idle switch/ ON or OFF
    		ON: Accelerator pedal released
    OFF: Accelerator pedal depressed
    		-
    Master Cylinder Sensor
    		Master cylinder pressure sensor reading/ Min.: 0.00 V, Max.: 5.00 V
    		When brake pedal released: 0.3 to 0.9 V
    		The value increases when the brake pedal is depressed.
    Zero Point of M/C
    		Memorized zero value/ Min.: -12.50 MPa, Max.: 12.40 MPa
    		-
    		-
    Accumulator Sensor
    		Accumulator pressure sensor reading/ Min.: 0.00 V, Max.: 5.00 V
    		3.58 to 5 V
    		If the value is constant regardless of the pump operation, an accumulator pressure sensor malfunction is suspected.
    Deceleration Sensor
    		Deceleration sensor reading/ Min.: -18.525 m/s2, Max.: 18.387 m/s2
    		-
    		Changes continuously during acceleration/deceleration.
    Zero Point of Decele
    		Memorized zero value/ Min.: -25.10 m/s2, Max.: 24.90 m/s2
    		-
    		-
    Forward and Rearward G
    		Forward and rearward G/ Min.: -25.10 m/s2, Max.: 24.90 m/s2
    		-
    		Changes in proportion with acceleration during acceleration/deceleration.
    Rear Diff Lock Switch
    		Rear differential lock detection switch/ ON or OFF
    		ON: Rear differential lock detection switch on
    OFF: Rear differential lock detection switch off
    		-
    L4 Switch
    		Transfer position switch status/ ON or OFF
    		ON: L4
    OFF: H4
    		-
    FR Wheel Speed
    		Front speed sensor RH reading/ Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph)
    		Actual wheel speed
    		No large fluctuations when driving at a constant speed.
    FL Wheel Speed
    		Front speed sensor LH reading/ Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph)
    		Actual wheel speed
    		No large fluctuations when driving at a constant speed.
    RR Wheel Speed
    		Rear speed sensor RH reading/ Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph)
    		Actual wheel speed
    		No large fluctuations when driving at a constant speed.
    RL Wheel Speed
    		Rear speed sensor LH reading/ Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph)
    		Actual wheel speed
    		No large fluctuations when driving at a constant speed.
    Vehicle Speed
    		Maximum wheel speed sensor reading/ Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph)
    		Actual vehicle speed
    		No large fluctuations when driving at a constant speed.
    FR Wheel Acceleration
    		Front wheel acceleration RH/ Min.: -200.84 m/s2, Max.: 199.27 m/s2
    		-
    		Changes continuously during acceleration/deceleration.
    FL Wheel Acceleration
    		Front wheel acceleration LH/ Min.: -200.84 m/s2, Max.: 199.27 m/s2
    		-
    		Changes continuously during acceleration/deceleration.
    RR Wheel Acceleration
    		Rear wheel acceleration RH/ Min.: -200.84 m/s2, Max.: 199.27 m/s2
    		-
    		Changes continuously during acceleration/deceleration.
    RL Wheel Acceleration
    		Rear wheel acceleration LH/ Min.: -200.84 m/s2, Max.: 199.27 m/s2
    		-
    		Changes continuously during acceleration/deceleration.
    FR Wheel Direction
    		Front wheel direction RH/ Forward or Back
    		Forward: Forward
    Back: Back
    		-
    FL Wheel Direction
    		Front wheel direction LH/ Forward or Back
    		Forward: Forward
    Back: Back
    		-
    RR Wheel Direction
    		Rear wheel direction RH/ Forward or Back
    		Forward: Forward
    Back: Back
    		-
    RL Wheel Direction
    		Rear wheel direction LH/ Forward or Back
    		Forward: Forward
    Back: Back
    		-
    FR Wheel ABS Ctrl Status
    		Front wheel RH ABS control status/ ON or OFF
    		ON: During control
    OFF: Not during control
    		-
    FL Wheel ABS Ctrl Status
    		Front wheel LH ABS control status/ ON or OFF
    		ON: During control
    OFF: Not during control
    		-
    RR Wheel ABS Ctrl Status
    		Rear wheel RH ABS control status/ ON or OFF
    		ON: During control
    OFF: Not during control
    		-
    RL Wheel ABS Ctrl Status
    		Rear wheel LH ABS control status/ ON or OFF
    		ON: During control
    OFF: Not during control
    		-
    RR Wheel EBD Ctrl Status
    		Rear wheel RH EBD control status/ ON or OFF
    		ON: During control
    OFF: Not during control
    		-
    RL Wheel EBD Ctrl Status
    		Rear wheel LH EBD control status/ ON or OFF
    		ON: During control
    OFF: Not during control
    		-
    BA Ctrl Status
    		BA control status/ ON or OFF
    		ON: During control
    OFF: Not during control
    		-
    Engine Revolutions
    		Engine speed/ Min.: 0 rpm, Max.: 65535 rpm
    		Actual engine speed
    		-
    Real Engine Torque
    		Actual engine torque/ Min.: -1024.0 Nm, Max.: 1023.0 Nm
    		-
    		-
    Accelerator Opening Angle %
    		Percentage of accelerator pedal opening angle/ Min.: 0.0%, Max.: 128.0%
    		When accelerator pedal released: 0%
    		Changes in proportion with the movement of the pedal during accelerator pedal operation.
    Solenoid Relay
    		Solenoid relay/ ON or OFF
    		ON: Solenoid relay on
    OFF: Solenoid relay off
    		-
    ECB* Motor Relay
    		Motor relay/ ON or OFF
    		ON: Motor relay on
    OFF: Motor relay off
    		-
    TR(A)C/VSC Solenoid (SRM2)
    		TRC/VSC solenoid (SRM2)/ ON or OFF
    		ON: Operating
    OFF: Not operating
    		-
    TR(A)C/VSC Solenoid (SRM1)
    		TRC/VSC solenoid (SRM1)/ ON or OFF
    		ON: Operating
    OFF: Not operating
    		-
    TR(A)C/VSC Solenoid (SRC2)
    		TRC/VSC solenoid (SRC2)/ ON or OFF
    		ON: Operating
    OFF: Not operating
    		-
    TR(A)C/VSC Solenoid (SRC1)
    		TRC/VSC solenoid (SRC1)/ ON or OFF
    		ON: Operating
    OFF: Not operating
    		-
    ABS Solenoid (SFRH)
    		ABS solenoid (SFRH)/ ON or OFF
    		ON: Operating
    OFF: Not operating
    		-
    ABS Solenoid (SFRR)
    		ABS solenoid (SFRR)/ ON or OFF
    		ON: Operating
    OFF: Not operating
    		-
    ABS Solenoid (SFLH)
    		ABS solenoid (SFLH)/ ON or OFF
    		ON: Operating
    OFF: Not operating
    		-
    ABS Solenoid (SFLR)
    		ABS solenoid (SFLR)/ ON or OFF
    		ON: Operating
    OFF: Not operating
    		-
    ABS Solenoid (SRRH)
    		ABS solenoid (SRRH)/ ON or OFF
    		ON: Operating
    OFF: Not operating
    		-
    ABS Solenoid (SRRR)
    		ABS solenoid (SRRR)/ ON or OFF
    		ON: Operating
    OFF: Not operating
    		-
    ABS Solenoid (SRLH)
    		ABS solenoid (SRLH)/ ON or OFF
    		ON: Operating
    OFF: Not operating
    		-
    ABS Solenoid (SRLR)
    		ABS solenoid (SRLR)/ ON or OFF
    		ON: Operating
    OFF: Not operating
    		-
    FR Speed Open
    		Front speed sensor RH open circuit detection/ Error or Normal
    		Normal
    		-
    FL Speed Open
    		Front speed sensor LH open circuit detection/ Error or Normal
    		Normal
    		-
    RR Speed Open
    		Rear speed sensor RH open circuit detection/ Error or Normal
    		Normal
    		-
    RL Speed Open
    		Rear speed sensor LH open circuit detection/ Error or Normal
    		Normal
    		-
    EFI Communication Open
    		ECM communication open circuit detection/ Error or Normal
    		Normal
    		-
    Deceleration Open
    		Deceleration sensor open circuit detection/ Error or Normal
    		Normal
    		-
    Master Cylinder Open
    		Master cylinder pressure sensor open circuit detection/ Error or Normal
    		Normal
    		-
    IG1 Voltage Value
    		IG1 voltage value/ Min.: 0.00 V, Max.: 20.00 V
    		Ignition switch ON: 11 to 14 V
    		-
    IG2 Voltage Value
    		IG2 voltage value/ Min.: 0.00 V, Max.: 20.00 V
    		Ignition switch ON: 11 to 14 V
    		-
    Number of DTC
    		Number of DTCs/ Min.: 0, Max.: 255
    		0
    		-
    IG Voltage Value Decreased
    		IG voltage value decreased detection/ Error or Normal
    		Normal
    		-
    IG Voltage Value Increased
    		IG voltage value increased detection/ Error or Normal
    		Normal
    		-
    FR Speed Sensor Voltage Open
    		Front speed sensor RH voltage open circuit detection/ Error or Normal
    		Normal
    		-
    FL Speed Sensor Voltage Open
    		Front speed sensor LH voltage open circuit detection/ Error or Normal
    		Normal
    		-
    RR Speed Sensor Voltage Open
    		Rear speed sensor RH voltage open circuit detection/ Error or Normal
    		Normal
    		-
    RL Speed Sensor Voltage Open
    		Rear speed sensor LH voltage open circuit detection/ Error or Normal
    		Normal
    		-
    M/C Pressure Sensor Noise
    		Master cylinder pressure sensor noise detection/ Error or Normal
    		Normal
    		-
    EFI Communication Invalid
    		ECM communication invalid detection/ Error or Normal
    		Normal
    		-
    Operation History of IG OFF while Vehicle is moving
    		History of ignition switch turned off when vehicle is in motion/ ON or OFF
    		ON: History of ignition switch turned off with vehicle speed 3 km/h (2 mph) or higher
    OFF: No history
    		-

    1. *: Electronically Controlled Brake

ACTIVE TEST
HINT:
Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

  1. Warm up the engine.

  2. Turn the ignition switch off.

  3. Connect the GTS to the DLC3.

  4. Turn the ignition switch to ON.

  5. Turn the GTS on.

  6. Enter the following menus: Chassis / ABS/VSC/TRC / Active Test.

  7. According to the display on the GTS, perform the Active Test.


ABS/VSC/TRC
Tester Display
Test Part
Control Range
Diagnostic Note
ABS Warning Light
ABS warning light
Warning light ON/OFF
Observe the combination meter.
Brake Warning Light
Brake warning light
Warning light ON/OFF
Observe the combination meter.
Buzzer
Buzzer
Buzzer ON/OFF
The buzzer can be heard.
Solenoid Relay
Solenoid relay
Relay ON/OFF
An operating sound of the solenoid (clicking sound) can be heard.
Motor Relay
Motor relay
Relay ON/OFF
An operating sound of the solenoid of the motor can be heard.
ABS Solenoid (SRLR)
ABS solenoid (SRLR)
Solenoid ON/OFF
An operating sound of the solenoid (clicking sound) can be heard.
ABS Solenoid (SRLH)
ABS solenoid (SRLH)
Solenoid ON/OFF
An operating sound of the solenoid (clicking sound) can be heard.
ABS Solenoid (SRRR)
ABS solenoid (SRRR)
Solenoid ON/OFF
An operating sound of the solenoid (clicking sound) can be heard.
ABS Solenoid (SRRH)
ABS solenoid (SRRH)
Solenoid ON/OFF
An operating sound of the solenoid (clicking sound) can be heard.
ABS Solenoid (SFLR)
ABS solenoid (SFLR)
Solenoid ON/OFF
An operating sound of the solenoid (clicking sound) can be heard.
ABS Solenoid (SFLH)
ABS solenoid (SFLH)
Solenoid ON/OFF
An operating sound of the solenoid (clicking sound) can be heard.
ABS Solenoid (SFRR)
ABS solenoid (SFRR)
Solenoid ON/OFF
An operating sound of the solenoid (clicking sound) can be heard.
ABS Solenoid (SFRH)
ABS solenoid (SFRH)
Solenoid ON/OFF
An operating sound of the solenoid (clicking sound) can be heard.
VSC/TRC Solenoid (SRMR)
VSC/TRC solenoid (SRM2)
Solenoid ON/OFF
An operating sound of the solenoid (clicking sound) can be heard.
VSC/TRC Solenoid (SRMF)
VSC/TRC solenoid (SRM1)
Solenoid ON/OFF
An operating sound of the solenoid (clicking sound) can be heard.
VSC/TRC Solenoid (SRCR)
VSC/TRC solenoid (SRC2)
Solenoid ON/OFF
An operating sound of the solenoid (clicking sound) can be heard.
VSC/TRC Solenoid (SRCF)
VSC/TRC solenoid (SRC1)
Solenoid ON/OFF
An operating sound of the solenoid (clicking sound) can be heard.
ABS Solenoid
Selection of multiple holding solenoids (SFRH, SFLH, SRRH and SRLH) and pressure reduction solenoids (SFRR, SFLR, SRRR and SRLR) possible
Start/Stop
-
VSC/TRC Solenoid
Selection of multiple VSC/TRC solenoids [SRMR (SRM2), SRMF (SRM1), SRCR (SRC2) and SRCF (SRC1)] possible
Start/Stop
-